Toshiba IK - TF1 User manual

TOSHIBA
INSTRUCTION MANUAL
3CCD CAMERA
IK-TF1
For Customer Use
Enter below the Serial No.
which is located on the
bottom of the cabinet. Retain
this information for future ref¬
erence.
Model No.: IK-TF1 _
Serial No.:
WARNING
This is a Class A of EN55022 product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A digital device, pursu¬
ant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
USER-INSTALLER CAUTION: Your authority to operate this FCC verified equipment could be voided if
P°rt'i* k < f a l modlficatlons not expressly approved by the party responsible for compliance to
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numerique de la classe A est comforme a la norme NMB-003 du Canada.

Read the following safety precautions carefully before using the product. These instructions
contain valuable information on safe and proper use that will prevent harm and damage to the
operator and other persons. Make sure that you fully understand the following details (indications,
graphic symbols) before proceeding to the main descriptions in this manual.
Indication definitions
Indication
Meaning
A
Warning
This indicates that ignoring this la¬
bel and/or misoperation of the prod¬
uct may cause serious personal in¬
jury or even death.
Graphic symbol definitions
a This indicates that ignoring this la-
/f\ bel and/or misoperation of the prod-
uct ma y cause personal injury* 1 and/
Cautlon | or material damaged |
*1: Bodily injury means injuries, burns and elec¬
tric shock which does not require hospitaliza- _
tion or prolonged treatment.
*2: Physical damage means extended harm to home
Symbol
Meaning
<s>
Indicates a prohibited action that
must not be carried out. The actual
prohibited action is indicated in the
symbol or nearby graphically or de¬
scribed in text.
Indicates a mandatory action that
O m u s t be carried out. The actual
mandatory action is indicated in the
symbol or nearby graphically or de¬
scribed in text.
household effects.
Do not use the product when abnormality occurs.
Use in the abnormal state such as smoke emitting from the product, burning smell, being
damaged by drop, invasion of foreign objects inside the product, etc., may cause fire and/
or electric shock. Always be sure to disconnect the power plug from the electrical outlet
(socket) at once and contact your dealer.
Do not install the product where splashing of water may occur, such as outdoor, a
bathroom, etc.
This may cause fire and/or electric shock.
Do not repair, disassemble and/or modify by yourself.
This may cause fire and/or electric shock. Always be sure to contact your dealer for internal
repair, check and cleaning of the product.
Keep the rated voltage for the product.
The use of power supply voltage outside the rated voltage may cause fire and/or electrical
shock. Please refer to "5.CONNECTIONS”.
Do not put a vessel(s) filled with a liquid (flower vase, etc.).
If a liquid enters the product, a fire and/or electric shock may occur.
Do not put the product in an unstable, slanting and/or vibrating place.
Drop and/or fall of the product may cause injury.
Do not touch power or TV antenna cords during a thunderstorm.
This might cause electric shock.

A
Follow these cautions when installing.
• Do not put the product on a Inflammable material such as carpet or blanket.
• Do not put the product in a narrow space, since the heat generated by the product may
cause fine.
• Do not put a inflammable material on the product.
If you do not keep above, the heat generated by the product may cause fire.
0
0
0
0
0
©
Do not put the product in direct sunshine and/or high temperature.
The temperature rise inside the product may cause fire.
Do not put the product In a moist or dusty place such as a bathroom, a place close to
a humidifier, etc.
This may cause fire and/or electric shock.
Do not put the product in a moist, soot/and/or dusty place such as a kitchen, etc.
Do not put the product where soot and steam may occur, such as a kitchen, etc., or in a
dusty place. This may cause fire and/or electric shock.
Do not shoot the sun with the lens and do not put the lens in the place exposed to an
intensive light, such as sunshine, etc.
Focusing of the light may cause injury of eye and/or fire.
Do not put the product in your mouth and do not swallow it.
This may cause suffocation and/or injury.
Ask your dealer to perform a periodical check and internal cleaning.
Dust inside the product may cause fire and/or trouble. For check and cleaning cost, please
consult your dealer.
3

TABLE OF CONTENTS
1. CAUTIONS ON USE AND INSTALLATION. 6
2. COMPONENTS. 6
3. ITEMS CONTROLLED BY USING ON SCREEN DISPLAY. 7
4. NAMES AND FUNCTIONS. 8
5. CONNECTION. 9
5.1 Standard Connection. g
5.2 Cautions on Connection. g
5.3 Connector Pin Assignments. g
6. OPERATION.10
6.1 White Balance. 10
6.2 Gain. 12
6.3 Shading Correction. 12
7. MODE SETTING BY ON SCREEN DISPLAY.13
7.1 Using the Menus. 13
7.2 Menus. 14
(1) SHUTTER (Electronic shutter). 14
(1.1) Changing each setting in MANUAL mode. 14
(1.2) Changing each setting in SS(synchro. scan) mode. 15
(1.3) Changing each setting in EXT TRIG mode. 16
(1.3.1) Changing each setting in 1 PULSE SNR mode. 16
(1.3.2) Changing each setting in 1 PULSE SR mode. 17
(1.3.3) Changing each setting in 2 PULSE mode. 18
(2) GAIN (Video gain). 19
(2.1) Changing each setting in GAIN. 19
(3) WHT BAL (White balance). 20
(3.1) Changing each setting in AWB (Automatic White Balance)mode. 20
(3.2) Changing each setting in MANUAL mode. 20
(4) PROCESS. 21
(4.1) Changing master pedestal.21
(4.2) Changing R pedestal. 21
(4.3) Changing B pedestal.21
(4.4) Changing White clip.21
(4.5) Changing shading correction mode. 21
(4.6) Changing manual shading correction . 21
(5) SYNC. 22
(5.1) Adjusting horizontal phase. 22
(5.2) Changing RGB SYNC. 22
4 |

(6) OPTION. 22
(6.1) Changing RS232C communication baud rate. 22
(7) Setting to factory setting status. 23
7.3 External Sync. 23
(1) External sync signal input conditions. 23
(2) External sync frequency range. 23
(3) Using the unit with external sync signal. 23
(3.1) H (horizontal) phase adjustment. 23
(4) Changing HD/VD input/output. 24
7.4 Synchro. Scan Operation. 24
(1) Setting by 1H. 24
(2) Setting by the frame. 24
7.5 EXT TRIG(Extemal trigger). 25
(1) 1 PULSE SNR (1 Pulse Sync Non Reset). 25
(2) 1 PULSE SR (1 Pulse Sync Reset). 27
(3) 2 PULSE. 28
8. BEFORE MAKING A SERVICE CALL.30
9. SPECIFICATIONS.30
10. EXTERNAL APPEARANCE DIAGRAM.31

1. CAUTIONS ON USE AND INSTALLATION
•Carefully handle the units.
Do not drop, or give a strong shock or vibration
to the camera. This may cause problems.
Treat the camera cables carefully to prevent
cable problems, such as cable breakdown and
loosened connections.
•Do not shoot intense light.
If there is an intense light at a location on the
screen such as a spot light, a blooming and
smearing may occur.
When intense light enters, vertical stripes may
appear on the screen. This is not a malfunction.
Ghosts may occur when there is an intense light
near the object. In this case, change the
shooting angle.
•Install the camera in a location free
from noise.
If the camera or the cables are located near
power utility lines or a TV, etc. undesirable
noise may appear on the screen. In such a
case, try to change the location of the camera
or the cable wiring.
•Moire
When thin stripe patterns are shooted, stripe
patterns that are not actually there (moire) may
appears as interference stripes. This is not a
malfunction.
•Operating ambient temperature and humidity.
Do not use the camera in places where temperature
and humidity exceed the specifications. Picture
quality will lower and internal parts may be
damaged.
Be particularly careful when using in places
exposed to direct sunlight. When shooting in hot
places, depending on the conditions of the object
and the camera (for example when the gain is
increased), noise in the form of vertical strips or
white dots may occur. This is not a malfunction.
•Handling of the protection cap.
Keep the protection cap away from children.
Children may put them into mouth or swallow them
accidentally. The protection cap protects the image
sensing plane when the lens is removed from the
camera, do not throw away.
•When not using the camera for a longtime.
Stop supplying power.
•When cleaning the camera
Always turn off the power and clean with a piece of
dry cloth. If necessary, gently wipe with a cloth
dampened with thinned detergent. Do not use
benzine, alcohol, thinner, etc. If used, coating and
printed letters may be discolored. When cleaning
the lens, use a lens cleaning paper, etc.
2. COMPONENTS
(1) Camera Control Unit.1
(2) Accessories
(a) Instruction manual.1
6

Electronic
shutter
Gain
White
balance
Process
Sync
Option
3. ITEMS CONTROLLED BY USING ON SCREEN DISPLAY
Available selections
MODE
MANUAL, SS, EXT TRIG
MANUAL
EXT TRIG
1 PULSE SNR, 1PULSESR, 2PULSE
1 PULSE SNR
MANUAL speed
OFF, 1/IOOs, 1/250s, 1/500s, 1/IOOOs, 1/2000S,
1/4000s, 1/10000s, 1/25000s, I/50000S
OFF
Syncro.
FLD
1/525H-260/525H, OFF, 1FRM-255FRM
OFF
scan.
FRM
1/525H-260/525H, OFF, 2FRM-256FRM
Storage mode
FLD, FRM
FLD
Trigger
(1 PULSE SNR/SR)
il v _r— l_ "i-r
jf L
T rigger(2PULSE)
1 PULSE exposure time
ji_n_ j .rir
0.02ms — 16ms
MODE
MANUAL, OFF
OFF
MANUAL
-3dB - 18dB OdB
MODE
AWB, MANUAL AWB
Color temperature
3200K, 5600K
3200K
MANUAL R GAIN
8
/
o
l
o o
0
MANUAL B GAIN
-100 ~ 0 ~ 100
0
Master pedestal
-64 ~ 0 ~ 64
0
R pedestal
-64 ~ 0 ~ 64
0
B pedestal
-64-0-64
0
White clip
-50-0-50
0
Shading correction mode
MANUAL, OFF
MANUAL
Manual shading correction
-128 - 0 - 127
0
H phase adjustment
-100 - 0 - 100
0
RGB SYNC
G, ALL ON, ALL OFF
G
Baud rate
9600bps, 19200bps
9600bps

4. NAMES AND FUNCTIONS
©DC IN 12V terminal
(DDISP button
©MENU UP button
©DATA UP(AWB) button
©DATA DOWN button
©MENU DOWN button
©RGB terminal
© Prism faceplate
(©DISP button
©PAGE button
©MENU UP button
©MENU DOWN button
©DATA UP (AWB) button
©DATA DOWN button
©DC IN 12V terminal
© RGB terminal
The protection cap is attached on the lens mount portion. After removing the
cap, mount the lens. Be careful not to scratch or touch the optical area.
Used when switching the display.
Used when switching to the menu and when selecting the menus.
Select the function to be confirmed or changed on the menu.
Select the function to be confirmed or changed on the menu.
Changes the value of the function selected by the MENU (UP/DOWN) button.
(Also used when using AWB.)
Changes the value of the function selected by the MENU (UP/DOWN) button.
Accept a DC power input (12V).
Used as the connector terminal for RGB output, and SYNC output.
HD and VD signals are input/output. When the random trigger operation is
used, the trigger signal is input and the index signal is output. This terminal
also includes an RS232C format control.

5. CONNECTION
5. 1 Standard Connection
5. 2 Cautions on Connection
When connecting the camera cables, be sure to turn off the camera and the other equipment
connected.
We suggest using a C mount lens made for a 3CCD camera.
When using another lens, the best camera performance of this camera may not be obtained.
(For example, low resolution may occur, focus may be lost through the range of a zoom lens, and
flare, ghost or shading may occur)
Furthermore, in order to avoid damaging the mounting portion of the camera head, use a lens
which has projection dimension from the mounting base of less than 0.157"(4mm).
For DC power supply connecting to DC IN 12V terminal, use UL listed and/or CSA
approved ungrounding type AC adaptor with the specifications described below.
Power supply voltage
Current rating
Ripple voltage
Connector
DC12V±10%
More than 830mA, Less than2.5A
Less than 50mV(p—p)
HR10A—7P—4S by HI ROSE electronics Co. Ltd
Pins 1,2 : 12V
Pins 3, 4 : GND
5. 3 Connector Pin Assignments
DC IN 12V
1
+12V
2
+12V
3 GND
4
GND
RGB
1
R
2
G
3
B
4
TXD
5 GND
6 GND
7
GND
8
SYNC
9
12V
10
GND
11
RXD
12
TRIG
13
HD IN/OUT
14
VD IN/OUT
15
INDEX
(f ©©©©gTI)
\\ © © © © © //
1 ^© © © © © J J

6. OPERATION
© Referring to the item “ 5. CONNECTION”, connect each equipment correctly.
(D Turn on the connected equipment and the camera.
® Pointing the lens at the object, operate the lens iris adjustment, focus adjustment, etc..
<D Referring to the item “6.1 White Balance”, operate the adjustment.
® Referring to the items “6.2 Gain, 7. MODE SETTING BY ON SCREEN DISPLAY”, select the necessary
items.
6. 1 White Balance
For the white balance adjustment for this unit, AWB (Automatic White Balance) and MANUAL (Manual
white balance) adjustments are provided. Referring to the items “7.2 (3) WHT BAL (White balance), 7.
MODE SETTING BY ON SCREEN DISPLAY”, select the desired mode.
AWB
(Automatic White Balance)
MANUAL
(Manual White Balance)
Outline
Adjust white balance by displaying the white
object inside the area set by AWB menu and
pressing the [DATA UP] button.
Adjust the white balance manually using the
WHT BAL menu while shooting the white
object.
Notes
When the shutter mode is EXT TRIG, AWB is
not available.
Adjustment is performed by confirming with a
waveform monitor.
© AWB(Automatic white balance)
• Set the MODE to AWB on the WHT BAL menu.
Perform the C.TEMP (color temperature conversion) setting, if necessary.
(Refer to the item “7.2 (3) WHT BAL (White balance)”.)
f" 3200K: Appropriate for indoor shooting.
[_ 5600K: Appropriate for outdoor shooting.
■ If the index menu/menu is displayed, press the [DISP] button to disable the color bar pattern or the
character display on the menu.
■ Shoot a known white object that fills the screen and push [DATA UP] button for approx. 1 second.
• The character AWB blinks on the screen when the AWB starts.
■ The character AWB stops blinking when the AWB finishes, and the result is displayed for approx. 1 second.
10