Toshiba FlashAir III User manual

GMAA00525010
594296-A0
03/15
If you need assistance:
❖Toshiba’s Support Web site: support.toshiba.com
❖Call Toshiba Customer Support Center
Within the United States at [phone]
Outside the United States at [phone]
Toshiba FlashAir™ III
Wireless SD™ Memory
Card
Quick Start

2
5.375 x 8.375 ver 2.3
Safety Information and Rules and
Regulations for Wireless LAN
❖Wireless LAN devices may cause interference with medical
equipment such as cardiac pacemakers. If you use personal medical
equipment, consult with your physician and medical equipment
instructions before using the Product. The Product should not be
used in environments with medical equipment such as hospitals and
medical offices, or near users of personal medical equipment.
❖Always turn off wireless functionality if the computer is near
automatic control equipment or appliances such as automatic doors
or fire detectors. Radio waves can cause malfunction of such
equipment, possibly resulting in serious injury.
❖Do not use the Wireless LAN functionality near a microwave oven or
in areas subject to radio interference or magnetic fields. Interference
from a microwave oven or other source can disrupt Wireless LAN
operation.
❖The transmission speed over the wireless LAN, and the distance over
which the wireless LAN can reach, may vary depending on
surrounding electromagnetic environment, obstacles, access point
design and configuration, client design and software/hardware
configurations. The transmission rate described is the theoretical
maximum speed as specified under the appropriate standard – the
actual transmission speed will be lower than the theoretical maximum
speed.
General Safety Instructions
❖Keep Product away from small children. This Product is not a toy and
may be hazardous to small children, for example, small detachable
parts may be a choking hazard.
❖Do not disassemble, modify, tamper with or repair your Product.
❖Dispose of Product or any components in compliance with all
applicable laws.
❖Never push a foreign object through an opening in the Product. Never
allow metal objects (such as screws, staples, or paper clips) to enter
Product. This could cause a short circuit.
❖Keep Product away from radiators, stoves, heat sources or other
equipment that produce heat.
❖Never expose your Product to excess heat, extremely low
temperatures, sudden temperature variations, or dusty environments.

3
5.375 x 8.375 ver 2.3
This could cause system malfunction, loss of data or damage to
Product.
❖Never operate your Product during a thunderstorm. An electrical
surge caused by the storm may cause system failure, loss of data or
hardware damage.
❖Turn off your Product and/or all wireless functionalities where
electronic devices are regulated or controlled or when near a person
with any medical electric devices.
❖Do not use Product in a wet location.
Regulatory Information
Federal Communications Commission
(FCC) Notice (USA)
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
❖Reorient or relocate the receiving antenna.
❖Increase the separation between the equipment and the receiver.
❖Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
❖Consult the dealer or an experienced radio or television technician for
help.
Changes or modifications made to this equipment not expressly approved by
Toshiba could void the user's authority to operate the equipment.
Declaration of Conformity of Products
Marked with the FCC Logo (USA)
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1This device may not cause harmful interference, and
2This device must accept any interference received, including
interference that may cause undesired operation.

4
5.375 x 8.375 ver 2.3
Canada Notice
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre
le fonctionnement.
To comply with the Canadian RF exposure compliance requirements, this
device and its antenna must not be co-located or operating in conjunction
with any other antenna or transmitter.
Pour être conforme aux exigences canadiennes en matière d'exposition aux
fréquences radio, l'appareil et son antenne ne doivent pas être situés au
meme endroit qu'une autre antenne ou un autre émetteur ni fonctionner en
meme temps.
The frequency band width of this equipment may operate within the same
range as industrial devices, scientific devices, medical devices, microwave
ovens, licensed radio stations and non licensed specified low-power radio
stations for mobile object identification systems (RFID) used in factory
production lines (Other Radio Station).
1Before using this equipment, ensure that it does not interfere with any
of the equipment listed above.
2If this equipment cause RF interference to other radio stations,
promptly change the frequency being used, change the location of
use, or turn off the source of emissions.
3Contact Toshiba Support if you have problems with interference
caused by this product to Other Radio Stations.
La largeur de bande de fréquences du produit peut recouper la gamme de
fréquences d’appareils industriels, scientifiques ou médicaux, de fours à
micro-ondes, de stations de radio sous licence et de stations de faible
puissance spécifiée sans licence pour les systèmes mobiles d’identification
d’objets (RFID) utilisés dans les lignes de production industrielles (autres
stations de radio).
1 Avant d’utiliser ce produit, assurez-vous qu’il n’interfère pas avec l’un
des appareils énumérés ci-dessus.
2 Si ce produit provoque des interférences RF avec d’autres stations de
radio, changez rapidement la fréquence utilisée, le lieu d’utilisation ou
désactivez la source d’émissions.

5
5.375 x 8.375 ver 2.3
3 Prenez contact avec le soutien Toshiba si vous avez des problèmes
d’interférences avec d’autres stations de radio provoqués par ce
produit.
Contact
Copyright
This manual may not be reproduced in any form without the prior written
permission of Toshiba. No liability is assumed with respect to the use of the
information contained herein.
© 2015 by Toshiba America Information Systems, Inc. All rights reserved.
Notice
The information contained in this manual, including but not limited to any
product specifications, is subject to change without notice.
TOSHIBA CORPORATION AND TOSHIBA AMERICA INFORMATION
SYSTEMS, INC. (TOSHIBA) PROVIDES NO WARRANTY WITH REGARD
TO THIS MANUAL OR ANY OTHER INFORMATION CONTAINED
HEREIN AND HEREBY EXPRESSLY DISCLAIMS ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY
PARTICULAR PURPOSE WITH REGARD TO ANY OF THE FOREGOING.
TOSHIBA ASSUMES NO LIABILITY FOR ANY DAMAGES INCURRED
DIRECTLY OR INDIRECTLY FROM ANY TECHNICAL OR
TYPOGRAPHICAL ERRORS OR OMISSIONS CONTAINED HEREIN OR
FOR DISCREPANCIES BETWEEN THE PRODUCT AND THE MANUAL.
IN NO EVENT SHALL TOSHIBA BE LIABLE FOR ANY INCIDENTAL,
CONSEQUENTIAL, SPECIAL, OR EXEMPLARY DAMAGES, WHETHER
BASED ON TORT, CONTRACT OR OTHERWISE, ARISING OUT OF OR
IN CONNECTION WITH THIS MANUAL OR ANY OTHER INFORMATION
CONTAINED HEREIN OR THE USE THEREOF.
Trademarks
FlashAir is a trademark of Toshiba America Information Systems, Inc. and/or
Toshiba Corporation.
Secure Digital, SD, and SDHC are trademarks or registered trademarks of
SD-3C, LLC in the United States, other countries or both.
All other brand and product names are trademarks or registered trademarks of
their respective companies.
Address: TOSHIBA America Information Systems, Inc.
9740 Irvine Boulevard
Irvine, California 92618-1697
Telephone: [phone]

6Check the components
5.375 x 8.375 ver 2.3
Check the components
The following items are shipped with your product:
❖FlashAir III wireless SD™ Memory Card
❖Warranty
Operation Procedure
Insert the FlashAir III wireless SD™ Memory Card into the SD™ Card
slot and double-click the FlashAirTool icon on your
device’s/computer’s desktop.
The following window appears when the software is initiated.
If the SD™ Card is not a FlashAir III wireless SD™ Memory Card or is
set to write-protected, the following message appears.
If this message appears, check that the card you inserted into the
SD™ Card slot is a FlashAir III wireless SD™ Memory Card and is
not set to write-protected, and then click Retry.

7
Main Menu window
5.375 x 8.375 ver 2.3
Main Menu window
If the software detects a FlashAir III wireless SD™ Memory Card, the
FlashAirTool Main Menu window appears.
1Drive
Shows the drive in which FlashAir III wireless SD™ Memory
Card is inserted.
2Network settings
The FlashAir III SSID, password, and other network settings
can be configured.
3Wireless LAN startup mode
The FlashAir III wireless LAN startup mode (Automatic startup
mode or Manual startup mode) can be configured.
4FlashAir drive setting
The FlashAir III Wireless SD™ Memory Card can be
configured to allow file transfer from the card to a computer
via wireless LAN connection using file management software.
5Initialize the card/change settings
Initialize the card: The card settings can be reset to the default
settings.
Change settings: The card can be configured to allow network
settings to be changed using the smartphone app.
6Help
The FlashAir III wireless SD™ Memory Card software manual
is displayed.
7Firmware version
The FlashAir III firmware version is displayed.

8Network settings
5.375 x 8.375 ver 2.3
Network settings
When Network settings is selected, the following window appears.
This window allows you to change the SSID and password. Enter a
new network name in the SSID field and a new password in the
Password field, and then click Apply.
❖SSID
The input field for the SSID.
The SSID is the network name that identifies a device for
wireless LAN communications.
The SSID can be up to thirty two (32) alphanumeric
characters.
❖Password
The input field for the password used to connect to FlashAir III
wireless SD™ Memory Card.
The password should have eight (8) to sixty three (63)
characters.
Be sure to use a secure password that is not easy to guess.
Toshiba recommends you make a note of your SSID and
password.
❖Use the same network settings, even after the card is
formatted
This option is available for FlashAir III W-02.

9
Network settings
5.375 x 8.375 ver 2.3
Wireless LAN startup mode
When Wireless LAN Startup mode is selected, the following
window appears. This window allows you to set the wireless LAN
startup mode.
There are two startup modes, Automatic startup mode and Manual
startup mode. Select a startup mode, and then click Apply.
❖Wireless LAN startup mode: Automatic startup mode
In this mode, the wireless LAN functionality of FlashAir III
wireless SD™ Memory Card runs automatically when the
device/computer the FlashAir III wireless SD™ Memory Card
is inserted into is powered on.
This option allows you to use the same network settings,
even after the card is formatted.
❖The SSID and password settings are maintained,
even if you format FlashAir III.
NOTE: The following procedure is required to reset the SSID
and password to their initial state.
❖Initialize the card using the FlashAir Tool (version
3.00 or later).
❖The “Initialize the card” feature may cause all data
stored in the FlashAir III wireless SD™ Memory
Card to be lost.
❖Back up your data to other storage media before
formatting the FlashAir III wireless SD™ Memory
Card.

10 Network settings
5.375 x 8.375 ver 2.3
❖Auto Start Timeout Setting
If there is no attempt to connect to the FlashAir III wireless
SD™ Memory Card from a device (e.g. a smartphone) within
the designated time previously set in the timeout settings, the
wireless LAN functionality automatically turns off.
To restart the wireless LAN functionality, turn off the
device/computer the FlashAir III wireless SD™ Memory Card
is inserted into, and then turn it on again.
Automatic startup mode is the default settings.
❖Wireless LAN startup mode: Manual startup mode
In this mode, you can enable/disable the wireless LAN
functionality by changing the write-protection status of the
wireless LAN startup image file.
First set your favorite photo as the wireless LAN startup
image.
When this image file is set to unprotected using the device’s
settings, the wireless LAN functionality is enabled.
When it is set to protected, the wireless LAN functionality is
disabled.
The status of the wireless LAN functionality changes only
when you change the write-protection status of the wireless
LAN startup image file.

11
Network settings
5.375 x 8.375 ver 2.3
Please note that when you power on a camera with this image
file unprotected, it is necessary to set it to protected and then
to unprotected again in order to enable the wireless LAN
functionality.
Wireless LAN startup image
You can change the wireless LAN startup image.
If you want to change the photo to another image file, choose Select
from file, click Browse, and then Open the image file.
The selected image file name is displayed in the file name field.
If you want to reset to the default image, select Default image.
Click Apply to change the “Current set Image” to the selected image
file.
❖The following image file is stored on the FlashAir III wireless
SD™ Memory Card as the default wireless LAN startup image.
/DCIM/100__TSB/FA000001.JPG
❖If you delete the image file that is set as the wireless LAN
startup image, you cannot enable the wireless LAN
functionality.
❖When not using the wireless LAN functionality, change the
Wireless LAN startup mode to Manual startup mode.
Using a digital still camera
The following is an example of the procedure used to set the wireless
LAN startup image file to protected or unprotected on a digital still
camera.
The name and the operation of the write-protection menu varies
depending on the digital still camera you are using.
For details, refer to your camera’s user’s manual.
1Set the digital still camera to play/display mode, and display
the wireless LAN startup image you have previously chosen.
2Press the digital still camera’s menu button and scroll to the
Protect menu.
3Set the wireless LAN startup image file to protected or
unprotected.

12 Format the Card
5.375 x 8.375 ver 2.3
Format the Card
If you format the FlashAir III wireless SD™ Memory Card using an
SDHC™ Memory Card compatible device (e.g. digital still camera),
initialize the card as follows to reset its wireless LAN functionality.
When Format the Card is selected, the following window appears.
This feature formats the FlashAir III wireless SD™ Memory Card and
resets it to the factory default settings.
All data stored in the FlashAir III wireless SD™ Memory Card may be
lost. Back up all data to other storage media before using this
feature.
The initial setup of the FlashAir III wireless SD™ Memory Card is
again required after formatting.
1Click Format.
2When the following message appears, make sure you have a
backup of all important data.
When you are ready, click Yes.

13
Format the Card
5.375 x 8.375 ver 2.3
The formatting process begins.
3When formatting is complete, the following message appears.
4After the “Setting a FlashAir” process is complete, the
following message appears.
Per the instructions in the following dialog box, remove
FlashAir III wireless SD™ Memory Card from the SD™ Card
slot and insert it again.
Click OK.
The FlashAir III wireless SD™ Memory Card is now reset to its
factory default settings.
When the format process is complete perform the initial setup for the
FlashAir III wireless SD™ Memory Card.

Si necesita ayuda:
❖Sitio web de asistencia técnica de Toshiba: support.toshiba.com
❖Llame al Centro de asistencia al cliente de Toshiba
Dentro de Estados Unidos al [phone]
Fuera de Estados Unidos al [phone]
Tarjeta de memoria SD™
Toshiba FlashAir™ III
inalámbrica
Inicio rápido

2
5.375 x 8.375 ver 2.3
Información de seguridad y normas y
reglamentos para LAN inalámbrica
❖Los dispositivos de LAN inalámbrica pueden causar interferencia con
dispositivos médicos, como marcapasos. Si usted utiliza equipo
médico personal, consulte a su médico y las instrucciones del equipo
médico antes de utilizar el Producto. El Producto no debe utilizarse
en entornos con equipo médico, como hospitales y consultorios
médicos, o cerca de usuarios con equipo médico personal.
❖Siempre apague la funcionalidad inalámbrica si la computadora se
encuentra cerca de equipo o aparatos de control automático, como
puertas automáticas o detectores de humo. La energía de
radiofrecuencia podría ocasionar la falla del equipo y posiblemente
provocar alguna lesión grave.
❖No utilice la funcionalidad de LAN inalámbrica cerca de un horno de
microondas o en áreas en las que haya interferencia de radio o
campos magnéticos. La interferencia de un horno de microondas u
otra fuente puede perturbar el funcionamiento de la LAN inalámbrica.
❖La velocidad de transmisión de la LAN inalámbrica y la distancia que
esta puede alcanzar pueden variar dependiendo del entorno
electromagnético, los obstáculos, el diseño y la configuración del
punto de acceso, el diseño del equipo del cliente y la configuración
de software/hardware. La velocidad de transmisión descrita es la
velocidad máxima teórica, según lo especificado bajo el estándar
correspondiente; la velocidad de transmisión real será menor que la
velocidad máxima teórica.
Instrucciones generales de seguridad
❖Mantenga el Producto fuera del alcance de los niños. Este Producto
no es un juguete y podría ser peligroso para los niños pequeños, ya
que las piezas desprendibles pequeñas pueden constituir un riesgo
de asfixia.
❖No desensamble, modifique, maneje indebidamente o repare el
Producto.
❖Deseche el Producto y cualquier componente de acuerdo con la
legislación vigente.
❖Nunca empuje un objeto extraño a través de un orificio del Producto.
Nunca permita el ingreso de objetos de metal (como tornillos, grapas
o sujetapapeles) en el Producto. Esto podría causar un cortocircuito.
❖Mantenga el Producto alejado de radiadores, estufas, fuentes de
calor u otros equipos que generen calor.

3
5.375 x 8.375 ver 2.3
❖Nunca exponga el Producto a calor excesivo, temperaturas muy
bajas, variaciones repentinas de temperatura o ambientes
polvorientos. Esto podría afectar el funcionamiento del sistema, o
causar pérdida de datos o daños al Producto.
❖Nunca opere el Producto durante una tormenta eléctrica. Una
descarga eléctrica causada por una tormenta puede causar fallos al
sistema, pérdida de datos o daños al hardware.
❖Apague el producto y/o todas las funciones inalámbricas donde el
uso de dispositivos electrónicos esté regulado o controlado, o
cuando se encuentra cerca de personas con dispositivos médicos
eléctricos.
❖No utilice el Producto en un lugar húmedo.
Información reglamentaria
Aviso de la Comisión Federal de
Comunicaciones (Federal
Communications Commission o FCC)
(EE. UU.)
Este equipo se probó y se comprobó que cumple con los límites para
dispositivos digitales de Clase B, en virtud de la Parte 15 de las normas de la
FCC. Estos límites están diseñados para proporcionar una protección
razonable contra interferencias perjudiciales en una instalación residencial.
Este equipo genera, utiliza y puede irradiar energía de radiofrecuencia y, si no
se instala y utiliza conforme a las instrucciones, puede interferir con las
comunicaciones por radio. Sin embargo, no se garantiza que no habrá
interferencias en una instalación en particular. Si este equipo provoca
interferencias en la recepción de radio o televisión (lo cual puede determinarse
apagando y encendiendo el equipo), recomendamos al usuario que intente
corregir la interferencia adoptando una o varias de las medidas siguientes:
❖Cambiar la orientación o la ubicación de la antena receptora.
❖Aumentar la distancia entre el equipo y el receptor.
❖Conectar el equipo a un tomacorriente en un circuito diferente al que
está conectado el receptor.
❖Consultar al distribuidor o a un técnico especializado en radio y
televisión para obtener ayuda.
Los cambios o las modificaciones realizadas a este equipo que no estén
aprobados expresamente por Toshiba pueden invalidar el derecho del usuario
a utilizar el equipo.

4
5.375 x 8.375 ver 2.3
Declaración de conformidad para los
productos marcados con el logotipo de la
FCC (EE. UU.)
Este dispositivo cumple con la Parte 15 de las normas de la FCC. El
funcionamiento está sujeto a las siguientes dos condiciones:
1Este dispositivo no debe causar interferencias y
2Este dispositivo debe aceptar cualquier interferencia recibida, incluidas
aquellas que puedan provocar un funcionamiento indeseado.
Aviso para Canadá
Este dispositivo cumple con las especificaciones de los estándares de radio
sin licencias de Industry Canada.
El funcionamiento está sujeto a las siguientes dos condiciones: (1) este
dispositivo no debe causar interferencias y (2) este dispositivo debe aceptar
cualquier interferencia recibida, incluidas aquellas que puedan provocar un
funcionamiento indeseado.
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre
le fonctionnement.
Para cumplir con los requisitos canadienses de exposición a radiofrecuencias,
este dispositivo y su antena no deberán colocarse en el mismo sitio ni
funcionar con ninguna otra antena o transmisor.
To comply with the Canadian RF exposure compliance requirements, this
device and its antenna must not be co-located or operating in conjunction
with any other antenna or transmitter.
Pour être conforme aux exigences canadiennes en matière d'exposition aux
fréquences radio, l'appareil et son antenne ne doivent pas être situés au
meme endroit qu'une autre antenne ou un autre émetteur ni fonctionner en
meme temps.

5
5.375 x 8.375 ver 2.3
El ancho de banda de este equipo puede utilizar el mismo rango de
frecuencias que los dispositivos industriales, científicos, médicos, hornos de
microondas, estaciones de radio autorizadas y estaciones de radio no
autorizadas de baja potencia especificada para sistemas de identificación de
objetos móviles (RFID) utilizados en líneas de producción industriales (otras
estaciones de radio).
1Antes de utilizar este equipo, asegúrese de que no interfiera con
ninguno de los equipos mencionados anteriormente.
2Si este equipo provoca interferencias de radiofrecuencia a otras
estaciones de radio, se debe cambiar rápidamente la frecuencia
utilizada, cambiar el emplazamiento para el uso o apagar la fuente de
emisiones.
3Póngase en contacto con el servicio de asistencia de Toshiba si tiene
problemas con la interferencia que este producto provoca en otras
estaciones de radio.
The frequency band width of this equipment may operate within the same
range as industrial devices, scientific devices, medical devices, microwave
ovens, licensed radio stations and non licensed specified low-power radio
stations for mobile object identification systems (RFID) used in factory
production lines (Other Radio Station).
1Before using this equipment, ensure that it does not interfere with any
of the equipment listed above.
2If this equipment causes RF interference to other radio stations,
promptly change the frequency being used, change the location of
use, or turn off the source of emissions.
3Contact Toshiba Support if you have problems with interference
caused by this product to Other Radio Stations.
La largeur de bande de fréquences du produit peut recouper la gamme de
fréquences d’appareils industriels, scientifiques ou médicaux, de fours à
micro-ondes, de stations de radio sous licence et de stations de faible
puissance spécifiée sans licence pour les systèmes mobiles d’identification
d’objets (RFID) utilisés dans les lignes de production industrielles (autres
stations de radio).
1 Avant d’utiliser ce produit, assurez-vous qu’il n’interfère pas avec l’un
des appareils énumérés ci-dessus.
2 Si ce produit provoque des interférences RF avec d’autres stations de
radio, changez rapidement la fréquence utilisée, le lieu d’utilisation ou
désactivez la source d’émissions.
3 Prenez contact avec le soutien Toshiba si vous avez des problèmes
d’interférences avec d’autres stations de radio provoqués par ce
produit.

6
5.375 x 8.375 ver 2.3
Contacto
Derechos de autor
Este manual no puede reproducirse en forma alguna sin el permiso previo y
por escrito de Toshiba. Toshiba no asume ninguna responsabilidad respecto al
uso de la información incluida en este manual.
© 2015 Toshiba America Information Systems, Inc. Todos los derechos
reservados.
Aviso
La información contenida en este manual, incluyendo pero sin limitarse a las
especificaciones del producto, está sujeta a modificaciones sin previo aviso.
TOSHIBA CORPORATION Y TOSHIBA AMERICA INFORMATION
SYSTEMS, INC. (TOSHIBA) NO BRINDAN NINGUNA GARANTÍA EN
RELACIÓN CON ESTE MANUAL O CON CUALQUIER INFORMACIÓN
EN ÉL CONTENIDA Y POR ESTE MEDIO SE LIBERAN
EXPRESAMENTE DE TODA RESPONSABILIDAD REFERENTE A
CUALQUIER GARANTÍA IMPLÍCITA DE COMERCIABILIDAD O
ADECUACIÓN PARA UN FIN CONCRETO RELACIONADO CON
CUALQUIERA DE LOS PUNTOS ANTES MENCIONADOS. TOSHIBA NO
ASUME NINGUNA RESPONSABILIDAD POR LOS DAÑOS SUFRIDOS
DIRECTA O INDIRECTAMENTE DEBIDO A ERRORES TÉCNICOS O
TIPOGRÁFICOS U OMISIONES EN ESTE MANUAL NI POR
DISCREPANCIAS ENTRE EL PRODUCTO Y EL MANUAL. TOSHIBA NO
ASUME BAJO NINGUNA CIRCUNSTANCIA RESPONSABILIDAD POR
DAÑOS INCIDENTALES, EMERGENTES, ESPECIALES O PUNITIVOS,
YA SEA DERIVADOS DE ACTOS CIVILES ILÍCITOS, CONTRATOS U
OTROS, QUE PUDIERAN DESPRENDERSE DE ESTE MANUAL O SE
RELACIONARAN CON EL MISMO O CON CUALQUIER OTRA
INFORMACIÓN EN ÉL CONTENIDA O CON EL USO QUE DE ELLA SE
HICIERA.
Marcas comerciales
FlashAir es una marca comercial de Toshiba America Information Systems,
Inc. y/o Toshiba Corporation.
Secure Digital, SD y SDHC son marcas comerciales o marcas registradas de
SD-3C, LLC en Estados Unidos y/u otros países.
Todos los demás nombres de marcas y productos son marcas comerciales o
marcas registradas de sus respectivas compañías.
Dirección: TOSHIBA America Information Systems, Inc.
9740 Irvine Boulevard
Irvine, California 92618-1697
Teléfono: [phone]