Toshiba Digital series Quick start guide

FUNCTIONALSPECIFICATION

Logical Drive MK3021 MK4021 MK6021 MK1031 MK2023

Parameters GAS GAS GAS GAS GAS

HDD2181 HDD2182 HDD2183 HDD2A02 HDD2187

No. of Cylinders (user) 47,080 47,080 47,080 69,840 34,040

Bytes per Sector 512 512 512 512 512

LBA Sectors 58,605,120 78,140,160 117,210,240 195,371,568 39,070,080

Buffer Size (KBYTES) 2048 2048 2048 8,192 2048

Rotation Speed (±.1%) 4200 4200 4200 4,200 4200

Transfer Rate 154.3 – 154.3 – 154.3 – 170.0 – 164.6 –

Internal (MBITS/sec) 298.0 298.0 298.0 373.0 257.1

No. of Cylinders(logical) 16,383 16,383 16,383 16383 16383

No. of Heads 16 16 16 16 16

No. of sec./Track 63 63 63 63 63

PIO/Ultra DMA (MBITS/sec) 16.6/100 16.6/100 16.6/100 16.6/100 16.6/100

SeekTime(MSEC.)

Average 12 12 12 12 12

Track-to-track 2 2 2 2 2

Maximum 22 22 22 22 22

TOSHIBA STORAGE DEVICE DIVISION

2.5" HDD SERIES INSTALLATION NOTES - 9.5mm GAS Series

Contents subject to change without prior notice.

GENERALDESCRIPTION

Toshiba’s 2.5" Hard Disk Drive 9.5mm GAS series, HDDXXXX, comprise a series of

fast, high-capacity 2.5" Winchester disk drives which comply with ATA-5 standards

and require only a simple adapter board for interfacing to standard IDE cables.

SPECIFICATIONS MK3021 MK4021 MK6021 MK1031 MK2023

GAS GAS GAS GAS GAS

HDD2181 HDD2182 HDD2183 HDD2A02 HDD2187

Formatted Capacity 30.00GB 40.00GB 60.00GB 100.030 20.003

Height 9.5mm 9.5mm 9.5mm 9.5mm 9.5mm

No. of Disks (platters) 1 2 2 2 1

No. of Data Heads 2 3 4 4 2

SPECIFICATIONS MK8025 MK6025 MK4025 MK3025

GAS GAS GAS GAS

HDD2188 HDD2189 HDD2190 HDD2196

Formatted Capacity 80.012 60.00GB 40.007GB 30.006GB

Height 9.5mm 9.5mm 9.5mm 9.5mm

No. of Disks (platters) 2 2 1 1

No. of Data Heads 4 4 2 2

CABLING INFORMATION

DRIVEINTERFACESIGNALS

PIN SIGNAL PIN SIGNAL

1 -RESET 2 GROUND

3 DD 7 4 DD 8

5 DD 6 6 DD 9

7 DD 5 8 DD 10

9 DD 4 10 DD 11

11 DD 3 12 DD 12

13 DD 2 14 DD 13

15 DD 1 16 DD 14

17 DD 0 18 DD 15

19 GROUND 20 KEY

21 DMARQ 22 GROUND

23 -DIOW 24 GROUND

STOP

25 -DIOR 26 GROUND

-DMARDY

HSTROBE

27 IORDY 28 CSEL

-DMARDY

-DSTROBE

29 -DMACK 30 GROUND

31 INTRQ 32 - IOCS16

33 DA1 34 -PDIAG

35 DA0 36 DA2

37 - CS0 38 - CS1

39 - DASP 40 GROUND

41 +5V(LOGIC) 42 +5V (MOTOR)

43 GROUND 44 RESERVED

Note: Symbol (–) in front of signal indicates negative logic.

TECHNICALSUPPORT

Should you require technical support, contact your computer distributor. If your

distributor is unable to answer your questions, have them call Toshiba Storage

Device Division Technical Support, on your behalf.

TOSHIBA - STORAGE DEVICE DIVISON

TECHNICAL SUPPORT - 503/615-4364

[email protected]

You can also visit Toshiba’s web site at: http://www.sdd.toshiba.com

2.5” Hard Disk Drive Installation Notes - 9.5mm GAS Series P/N480056-F0 P/N480056-F0 2.5” Hard Disk Drive Installation Notes - 9.5mm GAS Series

08/04 08/04

Logical Drive MK8025 MK6025 MK4025 MK3025

GAS GAS GAS GAS

HDD2187 HDD2188 HDD2189 HDD2190 HDD2196

No. of Cylinders (user) 54,000 42,480 54,000 42,480

Bytes per Sector 512 512 512 512

LBA Sectors 156,301,488 117,210,240 78,140,160 58,605,120

Buffer Size (KBYTES) 8,192 8,192 8,192 8192

RotationSpeed(±.1%) 4200 4200 4,200 4,200

Transfer Rate 175.0 – 201.6 – 175.0 – 201.6 –

Internal (MBITS/sec.) 341.7 307.5 341.7 307.5

No. of Cylinders (logical) 16,383 16,383 16,383 16,393

No. of Heads 16 16 16 16

No. of sec./Track 63 63 63 63

PIO/UltraDMA(MBITS/sec.) 16.6/100 16.1 16.6/100 16.6/100

SeekTime(MSEC.)

Average 12 12 12 12

Track-to-track 2 2 2 2

Maximum 22 22 22 22

FIGURE 1 – 2.5" HDD JUMPER LOCATIONS

JUMPER P28 DRIVE

No Jumper - Master Drive

C-D Jumper - Slave Drive

B-D Jumper LOW Master Drive

B-D Jumper HIGH Slave Drive

A-B Jumper - Slave Drive/

A-C Jumper - Prohibit

FIGURE 2 – MOUNTING HOLE LOCATIONS

INSTALLATIONINSTRUCTIONS

Note: Toshiba’s 2.5” HDDs are primarily used in notebook devices. Installation

into a notebook varies depending on the system manufacturer. Toshiba’s 2.5”

drives that are installed into a desktop PC require a 3.5” installation kit.

1. Determine mounting configuration (can be mounted in either a horizontal or

vertical orientation).

2. Configure drive for system application.

3. Configure the adapter board for the specific system application (if required).

4. Install the I/F cable to the System’s 44 pin connector port or adapter board.

Ensure Pin 1 is oriented correctly. (Pin 1 on the cable is usually identified by a

red or blue stripe.)

5. Refer to applicable manuals for software installation instructions.

KEY

PIN 20

1CA

JUMPER

INTERFACE

CONNECTOR

MOUNTINGHOLES

2.5” Hard Disk Drive Installation Notes - 9.5mm GAS Series P/N480056-F0 P/N480056-F0 2.5” Hard Disk Drive Installation Notes - 9.5mm GAS Series

08/04 08/04

UNPACKINGPROCEDURE

Visually inspect the shipping container prior to unpacking for any signs of damage

to the container or its contents (the carrier is responsible for any damage incurred

during shipment). The drive is a precision device and even a small drop onto any

surface can cause damage. Prior to opening the anti-static bag, it is recommended

that the user ground himself with a ground strap or by touching the PC chassis or

other metal object. Remove the drive from the anti-static bag and check it for

damage. Place the drive on the anti-static bag while configuring jumpers to avoid

any electrostatic discharge. Save the shipping container and packing material for

possible use later.

DRIVECONFIGURATION

Toshiba’s 2.5" hard disk drives can be configured as either master or slave units.

Master configuration is used for all single drive applications, and master or slave

configuration (only one of each per port) is used for two drive applications. Use the

information in the following table before setting M/S drive.

Master configuration is obtained by setting jumpers B, C & D open (no jumper).

Slave configuration is obtained by setting jumpers C-D. When B-D jumper is in-

stalled, the drive is configured as cable select. If pin 28 = Low, the drive is master.

If pin 28 = High, the drive is slave.