Toshiba MK4007GAL Quick start guide

MK4007GAL/MK8007GAH Hard Disk Drive Installation Notes P/N 480065-A0 P/N 480065-A0 MK4007GAL/MK8007GAH Hard Disk Drive Installation Notes
05/05 05/05
TOSHIBA STORAGE DEVICE DIVISION
MK4007GAL & MK8007GAH
HDD INSTALLATION NOTES
© 2005 Toshiba America Information Systems, Inc.
Contents subject to change without prior notice.
GENERAL DESCRIPTION
Toshiba’s MK4007GAL (HDD1622) and MK8007GAH (HDD1584) hard disk drive is
an ultra-slim fast 1.8 inch Winchester disk drive. The drive is ATA-6 compliant.
SPECIFICATIONS MK4007GAL MK8007GAH
HDD1622 HDD1584
FORMATTED CAPACITY 40.0GB 80.012GB
HEIGHT 5mm 8mm
WEIGHT 1.64 ounces (51g) 2.18 ounces (62g)
NO. OF DISKS (PLATTERS) 1 2
NO. OF DATA HEADS 2 4
FUNCTIONAL SPECIFICATION
LOGICAL DRIVE MK4007GAL MK8007GAH
PARAMETERS HDD1622 HDD1584
NO. OF CYLINDERS (user) 62,640
BYTES PER SECTOR 512
BUFFER SIZE 2MB
ROTATION SPEED (±0.1%) 4,200rpm
TRANSFER RATE INTERNAL 164.3 –341 Mbits/sec.
NO. OF CYLINDERS (logical) 16,383
NO. OF HEADS (logical) 16
NO. OF SECTORS/TRACK 63
HOST TRANSFER RATE
PIO/ULTRA DMA (ATA mode) 16.6/100MB/s
SEEK TIME
AVERAGE 15ms
TRACK-TO-TRACK 3ms
MAXIMUM 26ms
TEMPERATURE
OPERATING 41°F - 140°F (5°C - 60°C)
NON-OPERATING -4°F - 149°F (-20°C - 65°C)
HUMIDITY
OPERATING/NON-OPERATING 8 - 90% R.H. (No condensation)
SHIPPING 5 - 90% R.H. (No condensation)
WET BULB 29°C(operating)/40°C(non-operating)
CONNECTOR CABLING INFORMATION
PIN SIGNALS PIN SIGNALS
1 -RESET 2 GROUND
3 DD7 4 DD8
5 DD6 6 DD9
7 DD5 8 DD10
9 DD4 10 DD11
11 DD3 12 DD12
13 DD2 14 DD13
15 DD1 16 DD14
17 DD0 18 DD15
19 GROUND 20 OPEN
21 DMARQ, -DIOW 22 GROUND
23 STOP 24 GROUND
25 -DIOR 26 GROUND
-DMARDY
HSTROBE
27 IORDY 28 CSEL
-DMARDY
-DSTROBE
29 DMACK 30 GROUND
31 INTRQ 32 -IOCS16
33 DA1 34 - PDIAG/-CBLID
35 DA0 36 DA2
37 -CS0 38 -CS1
39 DASP 40 GROUND
41 + 3.3V (LOGIC) 42 + 3.3V (MOTOR)
43 GROUND 44 RESERVED
Note: “-“ in front of signal name indicates negative logic.

MK4007GAL/MK8007GAH Hard Disk Drive Installation Notes P/N 480065-A0 P/N 480065-A0 MK4007GAL/MK8007GAH Hard Disk Drive Installation Notes
05/05 05/05
UNPACKING PROCEDURE
Visually inspect the shipping container prior to unpacking for any signs of damage to
the container or its contents (the carrier is responsible for any damage incurred during
shipment). Prior to opening the anti-static bag, it is recommended that the user ground
himself with a ground strap or by touching the PC chassis or other metal object. Re-
move the drive from the anti-static bag and check it for damage. Save the shipping
container and packing material for possible use later.
HANDLING AND MOUNTING CONSIDERATIONS
•Installation and mounting of these drives is specific to the application environment.
•Handle drive only by the edges. When handling or mounting, take care not to apply
any pressure to the top cover.
•Avoid subjecting the drive to excessive shock. Do not drop the drive, even a
small distance onto a tabletop or other hard surface can damage drive. When
mounting the drive, do so in such a fashion that the drive will be isolated from
excessive shock.
•Do not mount in an environment where the temperature of the drive’s top cover will
exceed 65°C. (During operation, the temperature of the top cover can rise 15°C
above ambient).
•Do not disassemble, modify or repair drive.
•A rattle heard when the drive is moved is normal and not a sign of failure.
•The MK4007GAL and MK8007GAH do not use a standard ATA connector cable
(see Drive Connectors/Pin-out section for additional information.)
INTERFACE CONNECTOR
FIGURE 1 – INTERFACE CONNECTOR JUMPERS
JUMPER P28 DRIVE
No Jumper - Master Drive
C-D Jumper - Slave Drive
B-D Jumper LOW Master Drive
B-D Jumper HIGH Slave Drive
A-B Jumper - Prohibit
A-C Jumper - Prohibit
Three (Type A, B and C) Interface Connectors are available from Fujikura America Inc./
DDK Connector Division To contact them visit their website at (http://www.ddknet.co.jp).
FIGURE 2 – CONNECTORS A, B & C
FIGURE 3 – INTERFACE CONNECTOR
TECHNICAL SUPPORT
Should you require technical sup-
port, contact your computer dis-
tributor. If your distributor is unable to answer your questions, have them call Toshiba
Storage Device Division Technical Support, on your behalf.
TOSHIBA STORAGE DEVICE DIVISON TECHNICAL SUPPORT
Phone: [phone]
E-mail: [email protected]
FAX: [phone]
You can also visit Toshiba’s web site at: http://www.sdd.toshiba.com
DEVELOPER SUPPORT
Toshiba Storage Device Division (SDD) the industry pioneer in small form factor
storage supports developers who are looking for small form factor HDD’s that deliver
the unbeatable combination of high-performance and high-capacity storage. Toshiba
HDD’s can be found “under the hood” of some of today’s hottest portable products. If
you are interested in discussing your product application with us please contact us.
E-mail: [email protected]
Phone: [phone]
Fax: [phone]

MK4007GAL/MK8007GAH Hard Disk Drive Installation Notes P/N 480065-A0 P/N 480065-A0 MK4007GAL/MK8007GAH Hard Disk Drive Installation Notes
05/05 05/05
UNPACKING PROCEDURE
Visually inspect the shipping container prior to unpacking for any signs of damage to
the container or its contents (the carrier is responsible for any damage incurred during
shipment). Prior to opening the anti-static bag, it is recommended that the user ground
himself with a ground strap or by touching the PC chassis or other metal object. Re-
move the drive from the anti-static bag and check it for damage. Save the shipping
container and packing material for possible use later.
HANDLING AND MOUNTING CONSIDERATIONS
•Installation and mounting of these drives is specific to the application environment.
•Handle drive only by the edges. When handling or mounting, take care not to apply
any pressure to the top cover.
•Avoid subjecting the drive to excessive shock. Do not drop the drive, even a
small distance onto a tabletop or other hard surface can damage drive. When
mounting the drive, do so in such a fashion that the drive will be isolated from
excessive shock.
•Do not mount in an environment where the temperature of the drive’s top cover will
exceed 65°C. (During operation, the temperature of the top cover can rise 15°C
above ambient).
•Do not disassemble, modify or repair drive.
•A rattle heard when the drive is moved is normal and not a sign of failure.
•The MK4007GAL and MK8007GAH do not use a standard ATA connector cable
(see Drive Connectors/Pin-out section for additional information.)
INTERFACE CONNECTOR
FIGURE 1 – INTERFACE CONNECTOR JUMPERS
JUMPER P28 DRIVE
No Jumper - Master Drive
C-D Jumper - Slave Drive
B-D Jumper LOW Master Drive
B-D Jumper HIGH Slave Drive
A-B Jumper - Prohibit
A-C Jumper - Prohibit
Three (Type A, B and C) Interface Connectors are available from Fujikura America Inc./
DDK Connector Division To contact them visit their website at (http://www.ddknet.co.jp).
FIGURE 2 – CONNECTORS A, B & C
FIGURE 3 – INTERFACE CONNECTOR
TECHNICAL SUPPORT
Should you require technical sup-
port, contact your computer dis-
tributor. If your distributor is unable to answer your questions, have them call Toshiba
Storage Device Division Technical Support, on your behalf.
TOSHIBA STORAGE DEVICE DIVISON TECHNICAL SUPPORT
Phone: [phone]
E-mail: [email protected]
FAX: [phone]
You can also visit Toshiba’s web site at: http://www.sdd.toshiba.com
DEVELOPER SUPPORT
Toshiba Storage Device Division (SDD) the industry pioneer in small form factor
storage supports developers who are looking for small form factor HDD’s that deliver
the unbeatable combination of high-performance and high-capacity storage. Toshiba
HDD’s can be found “under the hood” of some of today’s hottest portable products. If
you are interested in discussing your product application with us please contact us.
E-mail: [email protected]
Phone: [phone]
Fax: [phone]

MK4007GAL/MK8007GAH Hard Disk Drive Installation Notes P/N 480065-A0 P/N 480065-A0 MK4007GAL/MK8007GAH Hard Disk Drive Installation Notes
05/05 05/05
TOSHIBA STORAGE DEVICE DIVISION
MK4007GAL & MK8007GAH
HDD INSTALLATION NOTES
© 2005 Toshiba America Information Systems, Inc.
Contents subject to change without prior notice.
GENERAL DESCRIPTION
Toshiba’s MK4007GAL (HDD1622) and MK8007GAH (HDD1584) hard disk drive is
an ultra-slim fast 1.8 inch Winchester disk drive. The drive is ATA-6 compliant.
SPECIFICATIONS MK4007GAL MK8007GAH
HDD1622 HDD1584
FORMATTED CAPACITY 40.0GB 80.012GB
HEIGHT 5mm 8mm
WEIGHT 1.64 ounces (51g) 2.18 ounces (62g)
NO. OF DISKS (PLATTERS) 1 2
NO. OF DATA HEADS 2 4
FUNCTIONAL SPECIFICATION
LOGICAL DRIVE MK4007GAL MK8007GAH
PARAMETERS HDD1622 HDD1584
NO. OF CYLINDERS (user) 62,640
BYTES PER SECTOR 512
BUFFER SIZE 2MB
ROTATION SPEED (±0.1%) 4,200rpm
TRANSFER RATE INTERNAL 164.3 –341 Mbits/sec.
NO. OF CYLINDERS (logical) 16,383
NO. OF HEADS (logical) 16
NO. OF SECTORS/TRACK 63
HOST TRANSFER RATE
PIO/ULTRA DMA (ATA mode) 16.6/100MB/s
SEEK TIME
AVERAGE 15ms
TRACK-TO-TRACK 3ms
MAXIMUM 26ms
TEMPERATURE
OPERATING 41°F - 140°F (5°C - 60°C)
NON-OPERATING -4°F - 149°F (-20°C - 65°C)
HUMIDITY
OPERATING/NON-OPERATING 8 - 90% R.H. (No condensation)
SHIPPING 5 - 90% R.H. (No condensation)
WET BULB 29°C(operating)/40°C(non-operating)
CONNECTOR CABLING INFORMATION
PIN SIGNALS PIN SIGNALS
1 -RESET 2 GROUND
3 DD7 4 DD8
5 DD6 6 DD9
7 DD5 8 DD10
9 DD4 10 DD11
11 DD3 12 DD12
13 DD2 14 DD13
15 DD1 16 DD14
17 DD0 18 DD15
19 GROUND 20 OPEN
21 DMARQ, -DIOW 22 GROUND
23 STOP 24 GROUND
25 -DIOR 26 GROUND
-DMARDY
HSTROBE
27 IORDY 28 CSEL
-DMARDY
-DSTROBE
29 DMACK 30 GROUND
31 INTRQ 32 -IOCS16
33 DA1 34 - PDIAG/-CBLID
35 DA0 36 DA2
37 -CS0 38 -CS1
39 DASP 40 GROUND
41 + 3.3V (LOGIC) 42 + 3.3V (MOTOR)
43 GROUND 44 RESERVED
Note: “-“ in front of signal name indicates negative logic.