Toshiba 32AF44 User manual

SERVICE MANUAL
Color Television
32AF44
32AFX54
N4NS Chassis
FILE NO. 020-200402

- 2 -
TABLE OF CONTENTS
CHAPTER 1 GENERAL ADJUSTMENTS
SAFETY INSTRUCTIONS ........................................................................................................................................ 3
SET-UP ADJUSTMENT ............................................................................................................................................ 4
SERVICE MODE ...................................................................................................................................................... 6
DESIGN MODE ........................................................................................................................................................ 9
ELECTRICAL ADJUSTMENT ................................................................................................................................ 10
CIRCUIT CHECKS ................................................................................................................................................. 12
CHAPTER 2 SPECIFIC INFORMATIONS
SETTING & ADJUSTING DATA .............................................................................................................................. 13
LOCATION OF CONTROLS ................................................................................................................................... 14
PROGRAMMING CHANNEL MEMORY ................................................................................................................. 16
CHASSIS AND CABINET REPLACEMENT PARTS LIST ......................................................................................17
PC BOARDS BOTTOM VIEW................................................................................................................................. 28
TERMINAL VIEW OF TRANSISTORS ................................................................................................................... 38
CIRCUIT BLOCK DIAGRAM .................................................................................................................................. 40
SPECIFICATIONS .............................................................................................................................................. END
APPENDIX:
CIRCUIT DIAGRAM

- 3 -
SAFETY INSTRUCTIONS
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRECAU-
TION” AND “PRODUCT SAFETY NOTICE” INSTRUCTIONS BELOW.
X-RAY RADIATION PRECAUTION
1. Excessive high voltage can produce potentially hazardous
X-RAY RADIATION. To avoid such hazards, the high volt-
age must not be above the specified limit. The nominal
value of the high voltage of this receiver is (A) kV at zero
beam current (minimum brightness) under a 120V AC
power source. The high voltage must not, under any cir-
cumstances, exceed (B) kV.
Refer to table-1 for high voltage (A), (B).
(See SETTING & ADJUSTING DATA on page 13)
Each time a receiver requires servicing, the high voltage
should be checked following the HIGH VOLTAGE CHECK
procedure in this manual. It is recommended that the read-
ing of the high voltage be recorded as a part of the service
record. It is important to use an accurate and reliable high
voltage meter.
2. This receiver is equipped with a Fail Safe (FS) circuit which
prevents the receiver from producing an excessively high
voltage even if the B+ voltage increases abnormally. Each
time the receiver is serviced, the FS circuit must be checked
to determine that the circuit is properly functioning, follow-
ing the FS CIRCUIT CHECK procedure in this manual.
3. The only source of X-RAY RADIATION in this TV receiver
is the picture tube. For continued X-RAY RADIATION pro-
tection, the replacement tube must be exactly the same
type tube as specified in the parts list.
4. Some part in this receiver have special safety-related char-
acteristics for X-RAY RADIATION protection. For contin-
ued safety, parts replacement should be undertaken only
after referring to the PRODUCT SAFETY NOTICE below.
SAFETY PRECAUTION
Connect a 1500 ohm 10 watt resistor, paralleled by a 0.15
µF, AC type capacitor, between a known good earth ground
(water pipe, conduit, etc.) and the exposed metallic parts,
one at a time. Measure the AC voltage across the combi-
nation of 1500 ohm resistor and 0.15 µF capacitor. Re-
verse the AC plug at the AC outlet and repeat AC voltage
measurements for each exposed metallic part. Voltage
measured must not exceed 0.3 volts rms.This corresponds
to 0.2 milliamp. AC. Any value exceeding this limit consti-
tutes a potential shock hazard and must be corrected im-
mediately.
WARNING : Service should not be attempted by anyone unfa-
miliar with the necessary precautions on this receiver. The fol-
lowing are the necessary precautions to be observed before
servicing this chassis.
1. An isolation Transformer should be connected in the power
line between the receiver and the AC line before any serv-
ice is performed on the receiver.
2. Always discharge the picture tube anode to the CRT con-
ductive coating before handling the picture tube. The pic-
ture tube is highly evacuated and if broken, glass frag-
ments will be violently expelled. Use shatter proof gog-
gles and keep picture tube away from the unprotected body
while handling.
3. When replacing a chassis in the cabinet, always be cer-
tain that all the protective devices are put back in place,
such as; non-metallic control knobs, insulating covers,
shields, isolation resistor-capacitor network etc.
4. Before returning the set to the customer, always perform
an AC leakage current check on the exposed metallic parts
of the cabinet, such as antennas, terminals, screwheads,
metal overlays, control shafts etc. to be sure the set is
safe to operate without danger of electrical shock. Plug
the AC line cord directly into a 120V AC outlet (do not use
a line isolation transformer during this check). Use an AC
voltmeter having 5000 ohms per volt or more sensitivity in
the following manner:
AC VOLTMETER
0.15µF
Good earth ground
such as a water
pipe, conduit, etc.
Place this probe on
each exposed
metallic part.
1500 ohm
10 watt
PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These characteristics are
often passed unnoticed by a visual inspection and the protection afforded by them cannot necessarily be obtained by using
replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety char-
acteristics are identified in this manual and its supplements; electrical components having such features are identified by
the international hazard symbols on the schematic diagram and the parts list.
Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement
parts which do not have the same safety characteristics as specified in the parts list may create shock, fire, X-ray
radiation or other hazards.
CHAPTER 1 GENERAL ADJUSTMENTS

- 4 -
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRECAU-
TION” AND “PRODUCT SAFETY NOTICE” ON PAGE 3 OF SERVICE MANUAL.
SET-UP ADJUSTMENT
■The following adjustments should be made when a complete realignment is required or a new picture tube is installed.
Perform the adjustments in order as follows :
1. Color Purity
2. Convergence
3. White Balance
Note: The PURITY/CONVERGENCE MAGNET assembly and rubber wedges need mechanical positioning.
Refer to figure 1.
COLOR PURITY ADUSTMENT
(1) Let the screen face in the installing direction or toward the east (when it is to be moved), bring up the service mode
screen after demagnetizing (front, left, right, and top) with the degaussing coil, receive white signals by pressing the
[TV/VIDEO] button, and then the receiver should be operated for more than 40 minutes.
(2) Perform rough adjustment of the central convergence with the P/C magnet according to the adjustment item.
(3) Receive built-in green signals, loosen set screws on the deflection yoke, remove rubber wedges, and shift the deflec-
tion yoke to toward front.
(4) Move alternately the two 2-pole magnets of the P/C magnets so that the green raster can come to the center of the
screen.
Figure 1.
(5) Receive built-in red and blue signals, check that there is no inclination of the single color raster toward one side, and if
each color tilts to a great extent, make adjustment with the 2-pole magnet so that the 3 colors will come to the center
evenly.
(6) Receive the green raster, shift the deflection yoke from
a foremost position (hitting against the picture tube) to a
backward position horizontally, stop the deflection yoke
at a position where it begins to become a green raster,
and perform accurate marking on the picture tube.
(7) Shift the deflection yoke further backward, and perform
accurate marking at a position where the green raster
begins to being luck.
(8) Fix the deflection yoke at a position 60% forward within
the range marked in items (6) and (7) above.
CONVERGENCE ADJUSTMENTS
* Adjust the convergence magnet to get vest convergence in the order to (1) ~ (5).
■ CENTER CONVERGENCE:
(1) Receive the white crosshatch or dot pattern from the service signal generator.
(2) Use the 2 pieces of main 4-pole magnets of P/C magnets, change the open angle, and align the red and blue vertical
lines on the screen center.
(3) Freeze the open angle of the main 4-pole magnets, turn them simultaneously, and align the horizontal lines.
(4) Take the same steps for items (2) and (3) above and align red/blue with green on the screen center using two 6-pole
magnets.
A
P/C magnet installing position A
• 30"=26.5 mm
• 32"=30.5 mm or 32.5 mm
• 34"=37 mm
• 34"=39 mm
Green Belt
2-pole purity magnet
(27": Magnet is fixed with deflection yoke.)
Main 4-pole convergence magnet (30" : 32")
6-pole convergence magnet (34")
Sub-4-pole convergence magnet (32" : 34")
Sub-4-pole convergence magnet (to be installed on deflection yoke for 30", 32”)
6-pole convergence magnet (30" : 32")
Main 4-pole convergence magnet (34")
Fix the deflection yoke at a position 60% forward from a
point between (6) and (7)
Picture tube
Shift deflection yoke
(6)
(8)
(7) Perform marking of each point
on the tape of picture tube
CRT-D board
P/C Mag
100 60 0%

- 5 -
– 5 –
(5) Adjust the sub-4-pole magnets only in case there is any deviation of Xv bow-shaped convergence. (To be usually set
at the initial position)
Align both sides with the sub-4-pole magnets and minimize the deviation of blue and red with the main 4-pole magnets.
blue
blue
red
red
Main 4-pole magnet
red/blue
red/blue
green
green
6-pole magnet
Xv bow-shaped deviation of convergence
blue
red
Sub-4-pole magnet
■CIRCUMFERENCE CONVERGENCE:
*
Perform correction in the following manner.
A
D
E
F
A
B
C
B
C
S
N
D
E
F
A
B
C
D
E
F
N
S
VR3
YV YHC
GH
GH
VR2 VR1
blue
green
red
• Adjust coils and minimize deviation
(The 27” unit has coils underneath it)
blue
green
red
(Parts code:23 948 274) TC-S
Blue color or blue mark
*Insert the correction piece between the
picture tube and the deflection yoke.
(Insertion position of correction
piece)
Bonded surface
blue
green
red
(Parts code:23 948 464)
Bonded surface
Adjust VR 1 and minimize the deviation of YH. *Only 27", 30" and 32".
Red
green
blue
Red
green
blue
Red
green
blue
Red
green
blue
Adjust VR 2 (YHC) and minimize the deviation of YH.
Red
green
blue
Red
green
blue
Red
green
blue
Red
green
blue
Adjust VR 3 (YV) and minimize the deviation of YV.
Red
blue
green
Red
blue
green
Red
blue
green
Red
blue
green
Red
blue
green
blue
red
green
Red
blue
green
blue
red
green
■ 30", 27", 32"
■ 34"
27" (Part No. 23 947 371)
32", 30" (Part No. 23 947 121)
34" (Part No. 23 993 080)
Perform correction by inserting the
correction piece into the clearance
of terminal board coils of the deflec-
tion yoke.
Note:
Perform insertion by turning the
metal side to the terminal board side
of the deflection yoke.

- 6 -
SERVICE MODE
1. ENTERING TO SERVICE MODE
MUTE
S
(Service mode display)
3) While pressing the MUTE button,
press MENU button on TV set.
2) Press MUTE button
again to keep pressing.
1) Press MUTE button once
on Remote Control.
2. DISPLAYING THE ADJUSTMENT MENU
1) Press MENU button on TV.
Adjustment mode
Press
Press
Service mode
Item
Data
S
3. KEY FUNCTION IN THE SERVICE MODE
The following key entry during display of adjustment menu provides special functions.
A single horizontal line ON/OFF: TV (ANT)/VIDEO button (on TV)
Test signal selection : TV (ANT)/VIDEO button (on Remote)
Selection of the adjustment items : Channel s/t(on TV or Remote)
Change of the data value : Volume s/t(on TV or Remote)
Adjustment menu mode ON/OFF : MENU button (on TV)
Initialization of the memory (QA02) : RECALL+Channel button on TV (s)
Initialization of the self diagnostic data: RECALL+Channel button on TV (t)
“RCUT” selection : 1 button
“GCUT” selection : 2 button
“BCUT” selection : 3 button
“SCNT” selection : 4 button
“COLC” selection : 5 button
“TNTC” selection : 6 button
Self diagnostic display ON/OFF : 9 button

- 7 -
4. SELECTING THE ADJUSTING ITEMS
1) Every pressing of CHANNEL sbutton in the service mode changes the adjustment items in the order of table-2.
(tbutton for reverse order)
Refer to table-2 for preset data of adjustment mode.
(See SETTING & ADJUSTING DATA on page 13)
5. ADJUSTING THE DATA
1) Pressing of VOLUME sor tbutton will change the value of data in the range from 00H to FFH. The variable range
depends on the adjusting item.
6. EXIT FROM SERVICE MODE
1) Pressing POWER button to turn off the TV once.
■INITIALIZATION OF MEMORY DATA OF QA02
After replacing QA02, the following initialization is required.
1. Enter the service mode, then select any register item.
2. Press and hold the RECALL button on the Remote, then press the CHANNEL sbutton on the TV.The initialization of QA02
has been complated.
3. Check the picture carefully. If necessary, adjust any adjustment item above.
Perform “Programming Channel Memory” on the owner’s manual.
CAUTION: Never attempt to initialize the data unless QA02 has been replaced.
7. TEST SIGNAL SELECTION
1) Every pressing of TV/VIDEO button on the Remote Control in the Service mode, changes the built-in test patterns
on screen in the following order.
Normal picture Black cross-bar
on green raster
Red raster
H signal (black)
H signal (white)
Green raster
Blue raster
White cross-dot
All black
Black cross-dot
All white
White cross-hatch
Black cross-hatch
White and black
Black cross-bar
White cross-bar
Signals Picture
• Red raster
• Green raster
• Blue raster
• All Black
• All White
• Black & White
• Black cross-hatch
• White cross-hatch
• Black cross-dot
• White cross-dot
• Black cross-bar
• White cross-bar
• Black cross-bar
on green raster
• H signal (white)
• H signal (black)
Note: If the video cable is connected to the VIDEO1 INPUT jack, the
built-in pattern signals are not displayed.
*The signals marked with are not usable to display in the Test signal for some model.

- 8 -
8. SELF DIAGNOSTIC FUNCTION
1) Press “9” button on Remote Control during display of adjustment menu in the service mode.
The diagnosis will begin to check if interface among IC’s are executed properly.
2) During diagnosis, the following displays are shown.
SELF CHECK
NO. 23 * * * * * *
POWER : 000
BUS LINE : OK
BUS CONT : OK
BLOCK : MAIN SUB
SET ID : 01
EEP VER : 02
OPT1 : 05 OPT2 : 70








*
The item marked with are not usable to display in the SELF DIAGNOSTIC FUNCTION for some model.
Part number of microprocessor (QA01)
Operation number of protection circuit (current limiter) . . . . “000” is normal.
BUS line check “OK” ................... Normal
“NG” ................... SCL-GND
or SAD-GND short circuit
BUS line ACK (acknowledge) check
“OK” ..................... Normal
Display of Location Number . . . . NG
(Display example)
“QA02 NG”, “H001 NG”, “Q501 NG” etc.
Note: The indication of failure place is only one place though failure places are plural. When
repair of a failure place finishes, the next failure place is indicated. (The order of priority of
indication is left side.)
Sync. signal check Green display ..... Normal
Cyan display ...... No check
Red display ........ NG
SET ID : 01 ←SET ID
EEP VER : 02 ←E2P version
OPT1 : 05 OPT2 : 70 ←OPT DATA

- 9 -
DESIGN MODE
1. ENTERING TO DESIGN MODE
Item
Data
S D Press
(Design mode) (Adjustment mode)
Press
3) Press MENU button on TV.
2) While pressing RECALL button on
Remote and press MENU button on TV.
1) Select the Service mode.
2. SELECTING THE ADJUSTING ITEMS
Every pressing of CHANNEL tbutton in the design mode changes the adjustment items in the order of table-3.
(sbutton for reverse order)
Refer to table-3 for data of design mode.
(See SETTING & ADJUSTING DATA on page 13)
3. ADJUSTING THE DATA
Pressing of VOLUME sor tbutton will change the value of data.
When QA02 is initialized, items “OPT0” and “OPT1” and "OPT2" of DESIGN MODE are set to the data of the representative
model of this chassis family.
Therefore, because ON-SCREEN specification remains in the state of the representative of model. This model is required to
reset the data of items “OPT0” and “OPT1” and "OPT2".

- 10 -
ELECTRICAL ADJUSTMENT
Vertical retrace line
1. Enter the service mode, then select any register item.
2. Press the TV/VIDEO button on the Remote until the black cross-bar pattern ap-
pears on the screen.
3. Adjust the FOCUS control (on T461) for well defined scanning lines on the picture
screen.
FOCUS VR ADJ
SUB-BRIGHTNESS
(BRTC)
1. Constrict the picture height until the
vertical retrace line appears adjusting
the HEIGHT control on the MAIN board.
2. Adjust the CONTRAST to the minimum
and BRIGHTNESS to the center.
3. Enter the service mode, then select
“BRTC” register.
4. Adjust the data value so the belt of
vertical retrace line just disappear.
5. Adjust the CONTRAST for the desired
contrast.
6. Adjust the HEIGHT control.
SUB-COLOR
(COLC)
SUB-TINT
(TNTC)
1. Receive color-bar signal from color-bar generator.
2. Press the RESET button.
3. Connect oscilloscope to base of Q906 on CRT-D board.
4. Enter the service mode, then select “COLC”.
5. Adjust the SUB-COLOR by pressing the
VOLUME sor tbutton to achieve about
1V
0-p of blue bar.
6. Select “TNTC” register.
7. Adjust the data value to obtain the blue
bar to magenta bar ratio of 3:2 as shown.
8. Select “COLC” register.
9. Adjust the data value to achieve 1.8V
0-p
of blue bar on scope.
10. Check the picture with off-air signal.
0
Blue
Magenta
2
3 (1.8V
0-P
)
WIDTH
(WID)
1. Call up the adjustment mode display, then select the item WID.
2. Press the VOLUME sor tbutton to get the picture so the left and right edges of
raster begins to lack.
3. Press the VOLUME sor tbutton to advance the data by 7 steps.
Note : Check the horizontal picture position is correct.
ITEM ADJUSTMENT PROCEDURE
E-W PARABOLA
(DPC)
1. Call up the adjustment mode display, then select the item DPC.
2. Press the TV/VIDEO button on Remote until the cross-hatch pattern appears on
the screen.
3. Press the VOLUME sor tbutton to make vertical lines straight as shown
below.

- 11 -
ITEM ADJUSTMENT PROCEDURE
HORIZONTAL POSITION
(HPOS)
VERTICAL POSITION
(VPOS)
1. Call up the adjustment mode display, then select the item HPOS or VPOS.
2. Press the TV/VIDEO button on Remote until the
white cross-bar or black cross-bar pattern appears
on the screen.
3. Adjust the HORIZONTAL and VERTICAL position
alternately by pressing the VOLUME sor tbutton
for proper picture position.
4. Check the picture with off-air signal.
HEIGHT
(HIT)
1. Call up the adjustment mode display, then select the item HIT.
2. Press the VOLUME sor tbutton to get the picture so the top of raster begins
to lack.
3. Press the VOLUME sbutton to advance the data by 9 steps.
Note : Check the vertical picture position is correct.
WHITE BALANCE
(RCUT)
(GCUT)
(BCUT)
(GDRV)
(BDRV)
1. Adjust the CONTRAST control to the center, and BRIGHTNESS control to the
maximum.
2. Call up the adjustment mode display, and press the TV/VIDEO button on
Remote until the white and black pattern appears on the screen.
3. Adjust the following item with the CHANNEL s/tand VOLUME s/tbuttons.
4. Press the TV/VIDEO button on TV to display a single horizontal line on the
screen.
5. Turn the SCREEN control (FBT) fully counterclockwise and gradually rotate
clockwise until the first horizontal line appears slightly on the screen.
6. Press the TV/VIDEO button to display the normal picture.
7. Adjust the remaining two “?CUT” items (CHANNEL s/t→ TV/VIDEO →
VOLUME s/tin order) to obtain the slightly lighted horizontal line in the same
levels of three (red, green, blue) colors. The line should be white if the adjust-
ments are proper.
Bright area
Adjust "GDRV" or "BDRV" to be white.
Dark area
Fine adjust "RCUT", "GCUT" or "BCUT" to be black.
RCUT Data : 40H
GCUT Data : 40H
BCUT Data : 40H
GDRV Data : 40H
BDRV Data : 40H
PIP SUB-BRIGHTNESS
(PBOF)
PIP WHITE BALANCE
(PGOF, PROF)
PIP SUB-TINT
(PHUE)
Adjust to match the PIP screen to the brightness, white balance and tint of the
main picture.

- 12 -
CIRCUIT CHECKS
Troubleshooting Guide for Fail Safe Circuit
Check that the set returns to normal operation when pin 12
of Z801(or emitter of Q472) is grounded with jumper wire.
Check the voltage across
Capacitor C471 is
approximately (C) volts.
Refer to table –4 for
fail safe voltage (C) .
Faulty power
circuit or hori-
zontal circuit.
Defective Fail Safe Circuit
(See SETTING & ADJUSTING
DATA on page13)
YES NO
NO
YES
HIGH VOLTAGE CHECK
CAUTION: There is no HIGH VOLTAGE ADJUSTMENT on
this chassis. Checking should be done following the steps
below.
1. Connect an accurate high voltage meter to the second an-
ode of the picture tube.
2. Turn on the receiver. Set the BRIGHTNESS and CON-
TRAST controls to minimum (zero beam current).
3. High voltage must be measured below (B) kV.
Refer to table-1 for high voltage (B).
(See SETTING & ADJUSTING DATA on page 13)
4. Vary the BRIGHTNESS control to both extremes to be sure
the high voltage does not exceed the limit under any con-
ditions.
FS CIRCUIT CHECK
The Fail Safe (FS) circuit check is indispensable for the final
check in servicing. Checking should be done following the
steps below.
1. Turn the receiver on and press the RESET button.
2. Temporarily short TP-(R) and TP-(X) with a jumper wire.
Raster and sound will disappear.
3. The receiver must remain in this state even after removing
the jumper wire. This is the evidence that the FS circuit is
functioning properly.
4. To obtain a picture again, temporarily turn the receiver off
and allow the FS circuit more than 5 seconds to reset.Then
turn the power switch on to produce a normal picture.

- 13 -
SETTING & ADJUSTING DATA
CHAPTER 2 SPECIFIC INFORMATIONS
Table-1
SAFETY INSTRUCTIONS
SERVICE MODE
ADJUSTING ITEMS AND DATAS IN THE SERVICE MODE:
RCUT
GCUT
BCUT
GDRV
BDRV
SCNT
BRTC
COLC
TNTC
SAVC
ATT
STVC
STRF
SPEC
WBAN
HPOS
VPOS
40H
40H
40H
40H
40H
0AH
40H
3AH
44H
20H
20H
20H
20H
20H
20H
16H
03H
Item Name of adjustment Preset Data
R CUTOFF
G CUTOFF
B CUTOFF
G DRIVE
B DRIVE
SUB-CONTRAST
SUB-BRIGHT
SUB-COLOR
SUB-TINT
SAP VCO
ATTENUATOR
STEREO VCO
STEREO FILTER
SPECTRAL
STEREO SEPARATION
HORIZ. POSITION
VERT. POSITION
Item Name of adjustment Preset
HIT
LIN
VSC
VPS
VCP
WID
DPC
CNR
TRAP
HCP
VFC
PCOL
PHUE
PGOF
PROF
PBOF
RGBB
HEIGHT
V-LINEARITY
V-S CORRECTION
V-SHIFT
V-COMPENSATION
PICTURE WIDTH
E-W PARABOLA (DPC)
E-W CORNER
TRAPEZIUM
H-COMPENSATION
V-F CORRECTION
PIP COLOR
PIP TINT
PIP
PIP
PIP
RGB BRIGHT
20H
08H
04H
01H
03H
17H
0CH
02H
06H
00H
0FH
0FH
11H
36H
17H
17H
0BH
←
08H
04H
←
←
17H
0CH
02H
06H
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
Table-2
DESIGN MODE
ADJUSTING ITEMS AND DATAS IN THE DESIGN MODE:
Item Name of adjustment Preset Data Data Remarks
Table-3
CIRCUIT CHECKS
Table-4
Data
OPT1 OPTION1 84H 84H
OPT2 OPTION2 01H 01H
32"
HIGH VOLTAGE AT ZERO BEAM: (A) 32.7kV
MAX HIGH VOLTAGE:
(B) 34.1kV
32"
FAIL SAFE DET. VOLTAGE
(C) 22.35 V

- 14 -
DEMO MENU TV/VIDEO VOLUME CHANNEL
VIDEO-3 IN
VIDEOS-VIDEO L/MONO-AUDIO-R
TV front
VIDEO 3 A/V IN
(with optional S-video)
POWER
MENU
VOLUME zy
CHANNEL zy
TV/VIDEO
DEMO Remote sensor
POWER indicator
x•zy
ANT(75 )
ANT-1
OUT
IN
S-VIDEO
VIDEO
VIDEO1 VIDEO 2
L/
MONO
AUDIO
R
DVDIN
P R
P B
Y
COLOR
STREAM
INPUT
L
AUDIO
R
L/
MONO
AUDIO
R
VIDEO
VAR/FIX
ANT( 75 )
OUT
IN
S-VIDEO
VIDEO
VIDEO 1 VIDEO 2
L/
MONO
AUDIO
R
DVD IN
P R
P B
Y
COLOR
STREAM
INPUT
L
AUDIO
R
L/
MONO
AUDIO
R
VIDEO
TV back
VIDEO 2
IN
{
{
ColorStream
(component
video) IN
ANT
IN
{
VIDEO 1
IN
{
A/V
OUT
{
LOCATION OF CONTROLS (Representative:32AF44)
Front View
Rear Term

- 15 -
}
RECALL [40]
FAV ts (favorite channels) [23]
Access channels programmed into
the Favorite Channel memory only.
TV/VIDEO [21]
EXIT [18]
VOLUME st
st TS [18]
MENU [18]
Channel numbers [20]
POWER
Device Switch [15,17]
Set to “TV” to control the TV.
CHANNEL st [20]
Access channels programmed
into the TV’s memory only.
VCR or DVD functions [17]
SLEEP [40]
{
}
MUTE [36]
PIC SIZE [22]
CH RTN (channel return) [23]
Remote Control

- 16 -
PROGRAMMING CHANNEL MEMORY
Programming channels automatically
Your TV can automatically detect all active channels in your area and
store them in the channel memory. After the channels are stored
automatically, you can manually add or erase individual channels
To program channels automatically:
1. Press MENU, and then press xor •until the SET UP menu
appears.
2. Press yor zuntil TV/CABLE is highlighted.
3. Press xor •to highlight either TV (if you use an antenna) or
CABLE (if you have cable service).
4. Press zto highlight CH PROGRAM.
MOVE SELECT
[ ]
[ ]
LANGUAGE:
TV/CABLE:
CH PROGRAM
ADD/ERASE:
MORE
[ENGLISH] FRANCAIS ESPANOL
[TV] CABLE
[ADD] ERASE
SET UP
MOVE SELECT
[ ]
[ ]
LANGUAGE:
TV/CABLE:
CH PROGRAM
ADD/ERASE:
MORE
[ENGLISH] FRANCAIS ESPANOL
[TV] CABLE
[ADD] ERASE
SET UP
5. Press xor •to start channel programming. The TV will
automatically cycle through all the TV or CABLE channels
(depending on which you selected), and store all active channels
in the channel memory.
While the TV is cycling through the channels, the message
“CH PROGRAM” appears.
6. When channel programming is complete, the message
“CH PROGRAMMING COMPLETED” appears.
7. Press CHANNEL yor zto view the programmed channels.
Adding and erasing channels manually
After you automatically program the channels into the channel
memory (see previous page), you can manually add or erase specific
channels.
To manually add or erase channels:
1. Select the channel you want to add or erase. If you are adding a
channel, you must select the channel using the Channel Number
buttons on the remote control.
2. Press MENU, and then press xor •until the SET UP menu
appears.
3. Press yor zto highlight ADD/ERASE.
MOVE SELECT
[ ]
[ ]
LANGUAGE:
TV/CABLE:
CH PROGRAM
ADD/ERASE:
MORE
[ENGLISH]
FRANCAIS ESPANOL
[TV] CABLE
[ADD] ERASE
SET UP
4. Press xor •to select ADD or ERASE, depending on the
function you want to perform.
5. Repeat steps 1–4 for other channels you want to add or erase.
When you press CHANNEL yor zon the remote control or
TV front panel, your TV will stop only on the channels stored in the
channel memory. Follow the steps below and on the next page to
program channels into the channel memory.

- 17 -
Location Parts No. Description
No.
Location Parts No. Description
No.
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRECAUTION”
AND “PRODUCT SAFETY NOTICE” ON PAGE 3 OF THIS MANUAL.
CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate com-ponents which
have special characteristics important for safety and should be replaced only with types identical to those in the original
circuit or specified in the parts list. The mounting position of replacements is to be identical with originals. Before replacing
any of these components, read carefully the PRODUCT SAFETY NOTICE. Do not degrade the safety of the receiver through
improper servicing.
NOTICE:
• The part number must be used when ordering parts, in order to assist in processing, be sure to include the Model
number and Description.
• The PC board assembly with ∗ mark is no longer available after the end of the production.
CHASSIS AND CABINET REPLACEMENT PARTS LIST
Model : 32AF44/32AFX54
Capacitors ............. CD : Ceramic Disk PF : Plastic Film EL : Electrolytic
Resistors ............... CF : Carbon Film CC : Carbon Composition MF : Metal Film
OMF : Oxide Metal Film VR : Variable Resistor FR : Fusible Resistor
(All CD and PF capacitors are ±5%, 50V and all resistors, ±5%, 1/6W unless otherwise noted.)
#1:[32AF44]
#2:[32AFX54]
CAPACITORS
C102 24792471 ELECTROLYTIC, 6.3V 470UF M
C105 24212102 CERAMIC DISC, 50V B 1000PF K
C106 24797479 ELECTROLYTIC, 50V 4.7UF M
C107 24763221 ELECTROLYTIC, 16V 220UF M
C201 24539104 PLASTIC FILM, 50V 0.1UF J
C204 24797010 ELECTROLYTIC, 50V 1UF M
C205 24794100 ELECTROLYTIC, 16V 10UF M
C213 24503041 PLASTIC FILM , 63V 0.1UF J
C216 24794100 ELECTROLYTIC, 16V 10UF M
C220 24539474 PLASTIC FILM, 50V 0.47UF J
C221 24109103 CERAMIC CHIP, 50V B 0.01UF K
C222 24109103 CERAMIC CHIP, 50V B 0.01UF K
C223 24109103 CERAMIC CHIP, 50V B 0.01UF K
C224 24539104 PLASTIC FILM, 50V 0.1UF J
C225 24539104 PLASTIC FILM, 50V 0.1UF J
C226 24539104 PLASTIC FILM, 50V 0.1UF J
C245 24206108 ELECTROLYTIC 04W, 50V 0.1UF M 7L 3A
C261 24539104 PLASTIC FILM, 50V 0.1UF J
C262 24539104 PLASTIC FILM, 50V 0.1UF J
C263 24539104 PLASTIC FILM, 50V 0.1UF J
C271 24109561 CERAMIC CHIP, 50V B 560PF K
C304 24693273 PLASTIC FILM, 100V 0.027UF J
C305 24617915 ELECTROLYTIC, 50V 1UF K 3A LI
C306 24073059 ELECTROLYTIC, 25V 3300UF M 3A
C308 24668221 ELECTROLYTIC, 35V 220UF M 3A
C309 24436101 CERAMIC DISC, 50V SL 100PF J
C310 24766102 ELECTROLYTIC, 50V 1000UF M
C311 24214152 CERAMIC DISC, 500V B 1500PF K
C313 24082057 PLASTIC FILM, 100V 0.22UF J
C314 24436680 CERAMIC DISC, 50V SL 68PF J
24436680 CERAMIC DISC, 50V SL 68PF J
C315 24109102 CERAMIC CHIP, 50V B 1000PF K
C317 24214471 CERAMIC DISC, 500V B 470PF K
C319 24109273 CERAMIC CHIP, 25V B 0.027UF K
C320 24797101 ELECTROLYTIC, 50V 100UF M
C323 24539474 PLASTIC FILM, 50V 0.47UF J
C324 24503037 MT PLA CAP 63V 0.047UF J
C325 24539683 PLASTIC FILM, 50V 0.068UF J
C326 24539104 PLASTIC FILM, 50V 0.1UF J
C327 24617915 ELECTROLYTIC, 50V 1UF K 3A LI
C337 24797229 ELECTROLYTIC, 50V 2.2UF M
C370 24794101 ELECTROLYTIC, 16V 100UF M
C371 24794100 ELECTROLYTIC, 16V 10UF M
C403 24539103 PLASTIC FILM, 50V 0.01UF J
C404 24797010 ELECTROLYTIC, 50V 1UF M
C407 24539104 PLASTIC FILM, 50V 0.1UF J
C408 24109273 CERAMIC CHIP, 25V B 0.027UF K
C410 24109103 CERAMIC CHIP, 50V B 0.01UF K
C412 24214472 CERAMIC DISC, 500V B 4700PF K
C413 24214821 CERAMIC DISC, 500V B 820PF K
C415 24539224 PLASTIC FILM, 50V 0.22UF J
C416 24678010 ELECTROLYTIC, 200V 1UF M 3A
C417 24214331 CERAMIC DISC, 500V B 330PF K
C430 24109103 CERAMIC CHIP, 50V B 0.01UF K
C431 24794101 ELECTROLYTIC, 16V 100UF M
C439 24503125 PLASTIC FILM, 400V 0.075UF J
C441 24503305 PLASTIC FILM CF92 T 315V R62UF J
C442 24503298 PLASTIC FILM, 315V 0.3UF J
C443 24503274 PLASTIC FILM CF92 T 1500VH 7800PF H
C444 24503080 PLASTIC FILM CF92 T 1800VH 7500PF H
C445 24828563 PLASTIC FILM, 200V 56000PF J
C446 24679100 ELECTROLYTIC, 250V 10UF M 3A
C448 24640908 ELECTROLYTIC, 160V 33UF M 3A LI
C451 24085981 ELEC. NONPOLAR CE04J 16V 10UF M 11L NP
C457 24591222 PLASTIC FILM, 50V 2200PF J
C463 24212152 CERAMIC DISC, 50V B 1500PF K
C464 24640872 ELECTROLYTIC, 100V 10UF M 3A
C466 24503037 MT PLA CAP 63V 0.047UF J
C467 24820273 PLASTIC FILM, 630V 27000PF J
C469 24820243 PLASTIC FILM CQ92 T 630V 24000PF
C471 24797479 ELECTROLYTIC, 50V 4.7UF M
C474 24794100 ELECTROLYTIC, 16V 10UF M
C480 24747220 ELECTROLYTIC, 50V 22UF M 7L 3A
C481 24539474 PLASTIC FILM, 50V 0.47UF J
C482 24797478 ELECTROLYTIC, 50V 0.47UF M
C483 24206108 ELECTROLYTIC 04W, 50V 0.1UF M 7L 3A
C499 24212102 CERAMIC DISC, 50V B 1000PF K
C501 24109102 CERAMIC CHIP, 50V B 1000PF K

Location Parts No. Description
No.
Location Parts No. Description
No.
- 18 -
C504 24591222 PLASTIC FILM, 50V 2200PF J
C505 24105130 CERAMIC CHIP, 50V CH 13PF J
C510 24109103 CERAMIC CHIP, 50V B 0.01UF K
C511 24794101 ELECTROLYTIC, 16V 100UF M
C512 24206228
ELECTROLYTIC, 50V 0.22UF M 7L 3A CE04WS
C582 24109103 CERAMIC CHIP, 50V B 0.01UF K
C583 24762471 ELECTROLYTIC, 04G 10V 470UF M
C614 24794470 ELECTROLYTIC, 16V 47UF M
C615 24092730 CERAMIC CHIP, 16V B 0.1UF K
C661 24109102 CERAMIC CHIP, 50V B 1000PF K
C662 24212102 CERAMIC DISC, 50V B 1000PF K
C663 24794100 ELECTROLYTIC, 16V 10UF M
C672 24667470 ELECTROLYTIC CE04Q, 25V 47UF M 3A
C673 24797229 ELECTROLYTIC, 50V 2.2UF M
C674 24669010 ELECTROLYTIC, 50V 1UF M 3A
C675 24669010 ELECTROLYTIC, 50V 1UF M 3A
C676 24285104 CERAMIC CHIP, 50V B 0.1UF K
C677 24503041 PLASTIC FILM , 63V 0.1UF J
C678 24797229 ELECTROLYTIC, 50V 2.2UF M
C681 24668102 ELECTROLYTIC, 35V 1000UF M 3A
C682 24669221 ELECTROLYTIC, 50V 220UF M 3A
C683 24668102 ELECTROLYTIC, 35V 1000UF M 3A
C684 24100103 CERAMIC CHIP, 50V F 0.01UF Z
C704 24232103 CERAMIC DISC, 50V F 0.01UF Z
C705 24232103 CERAMIC DISC, 50V F 0.01UF Z
C707 24794101 ELECTROLYTIC, 16V 100UF M
C713 24709100 ELECTROLYTIC, 200V 10UF M
C714 24436101 CERAMIC DISC, 50V SL 100PF J
C715 24214472 CERAMIC DISC, 500V B 4700PF K
C716 24436101 CERAMIC DISC, 50V SL 100PF J
C717 24214472 CERAMIC DISC, 500V B 4700PF K
C718 24794470 ELECTROLYTIC, 16V 47UF M
C719 24435560 CERAMIC DISC, 500V SL 56PF J
C720 24709100 ELECTROLYTIC, 200V 10UF M
C721 24794470 ELECTROLYTIC, 16V 47UF M
C726 24212102 CERAMIC DISC, 50V B 1000PF K
C801 24503002 PLASTIC FILM, AC275V 0.22UF M
C802 24503001 PLASTIC FILM, AC275V 0.1UF M
C805 24092623 CERAMIC DISC, 250V F 0.01UF Z
C806 24092623 CERAMIC DISC, 250V F 0.01UF Z
C808 24667221 ELECTROLYTIC CE04Q, 25V 220UF M 3A
C810 24086061 ELECTROLYTIC, 200V 470UF M 3F
C811 24092581 CERAMIC DISC, AC250V E 1000PF M
C812 24092581 CERAMIC DISC, AC250V E 1000PF M
C813 24092583 CERAMIC DISC, AC250V E 2200PF M
C817 24092339 CERAMIC DISC, 2KV 330PF K
C818 24503237 PLASTIC FILM CF92 T 1250VH 2200PF H
C821 24214471 CERAMIC DISC, 500V B 470PF K
C822 24590223 PLASTIC FILM, 50V 0.022UF J
C823 24212471 CERAMIC DISC, 50V B 470PF K
C829 24591152 PLASTIC FILM, 50V 1500PF J
C830 24503047 PLASTIC FILM, 63V 0.33UF J
C831 24503047 PLASTIC FILM, 63V 0.33UF J
C832 24503047 PLASTIC FILM, 63V 0.33UF J
C834 24503047 PLASTIC FILM, 63V 0.33UF J
C840 24795221 ELECTROLYTIC CE04G, 25V 220UF M
C842 24792101 ELECTROLYTIC CE04G, 6.3V 100UF M
C843 24797479 ELECTROLYTIC, 50V 4.7UF M
C884 24086052 ELECTRORYTIC, 200V 220UF M 22A
C886 24214471 CERAMIC DISC, 500V B 470PF K
C889 24796222 ELECTROLYTIC, 35V 2200UF M
C890 24214471 CERAMIC DISC, 500V B 470PF K
C891 24503041 PLASTIC FILM , 63V 0.1UF J
C893 24092339 CERAMIC DISC, 2KV 330PF K
C896 24794471 ELECTROLYTIC, 16V 470UF M
C897 24794222 ELECTROLYTIC, 16V 2200UF M
C902 24092353 CERAMIC DISC, 2KV 4700PF K
C904 24436331 CERAMIC DISC, 50V SL 330PF J
C905 24436331 CERAMIC DISC, 50V SL 330PF J
C907 24436331 CERAMIC DISC, 50V SL 330PF J
C909 24679220 ELECTROLYTIC, 250V 22UF M 3A
C910 24797478 ELECTROLYTIC, 50V 0.47UF M
C911 24794100 ELECTROLYTIC, 16V 10UF M
C912 24763471 ELECTROLYTIC, 16V 470UF M
C913 24794100 ELECTROLYTIC, 16V 10UF M
C914 24232103 CERAMIC DISC, 50V F 0.01UF Z
C920 24232103 CERAMIC DISC, 50V F 0.01UF Z
C921 24232103 CERAMIC DISC, 50V F 0.01UF Z
C930 24214101 CERAMIC DISC, 500V B 100PF K
C970 24794470 ELECTROLYTIC, 16V 47UF M
C971 24794470 ELECTROLYTIC, 16V 47UF M
C972 24794470 ELECTROLYTIC, 16V 47UF M
C2701 24109103 CERAMIC CHIP, 50V B 0.01UF K
C2702 24539474 PLASTIC FILM, 50V 0.47UF J
C2703 24109472 CERAMIC CHIP, 50V B 4700PF K
C2704 24794100 ELECTROLYTIC, 16V 10UF M
C2707 24105150 CERAMIC CHIP, 50V CH 15PF J
C2710 24109103 CERAMIC CHIP, 50V B 0.01UF K
C2711 24794100 ELECTROLYTIC, 16V 10UF M
C2715 24109103 CERAMIC CHIP, 50V B 0.01UF K
CA03 24105471 CERAMIC CHIP, 50V CH 470PF J
CA04 24105471 CERAMIC CHIP, 50V CH 470PF J
CA05 24105471 CERAMIC CHIP, 50V CH 470PF J
CA06 24105471 CERAMIC CHIP, 50V CH 470PF J
CA32 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CA37 24105101 CERAMIC CHIP, 50V CH 100PF J
CA38 24105101 CERAMIC CHIP, 50V CH 100PF J
CA42 24794100 ELECTROLYTIC, 16V 10UF M
CA43 24109103 CERAMIC CHIP, 50V B 0.01UF K
CA44 24109103 CERAMIC CHIP, 50V B 0.01UF K
CA68 24794100 ELECTROLYTIC, 16V 10UF M
CA69 24109103 CERAMIC CHIP, 50V B 0.01UF K
CB01 24794470 ELECTROLYTIC, 16V 47UF M
CB41 24763221 ELECTROLYTIC, 16V 220UF M
CB48 24105101 CERAMIC CHIP, 50V CH 100PF J
CB60 24085944
ELECTROLYTIC, NONPOLAR, 50V 2.2UF M 11L
CB61 24591102 PLASTIC FILM, 50V 1000PF J
CB62 24109561 CERAMIC CHIP, 50V B 560PF K
CB63 24109122 CERAMIC CHIP, 50V B 1200PF K
CB64 24763471 ELECTROLYTIC, 16V 470UF M
CB65 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CD41 24109332 CERAMIC CHIP, 50V B 3300PF K
CD42 24109333 CERAMIC CHIP CK73B 25V 33000PFK
CD43 24797479 ELECTROLYTIC, 50V 4.7UF M
CD44 24797479 ELECTROLYTIC, 50V 4.7UF M
CD45 24109182 CERAMIC CHIP, 50V B 1800PF K
CD46 24092753 CERAMIC CHIP, 10V B 0.22UF K
CD47 24109103 CERAMIC CHIP, 50V B 0.01UF K
CD48 24794100 ELECTROLYTIC, 16V 10UF M
CD49 24092730 CERAMIC CHIP, 16V B 0.1UF K
CD50 24797479 ELECTROLYTIC, 50V 4.7UF M
CD51 24797479 ELECTROLYTIC, 50V 4.7UF M
CD52 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CD53 24794221 ELECTROIYTIC 04G, 16V 220UF M
CD54 24797479 ELECTROLYTIC, 50V 4.7UF M
CD55 24797479 ELECTROLYTIC, 50V 4.7UF M
CD56 24797479 ELECTROLYTIC, 50V 4.7UF M
CD57 24092730 CERAMIC CHIP, 16V B 0.1UF K
CD58 24109103 CERAMIC CHIP, 50V B 0.01UF K
CD59 24092753 CERAMIC CHIP, 10V B 0.22UF K
CD60 24109182 CERAMIC CHIP, 50V B 1800PF K
CD61 24797479 ELECTROLYTIC, 50V 4.7UF M

Location Parts No. Description
No.
Location Parts No. Description
No.
- 19 -
CD62 24797479 ELECTROLYTIC, 50V 4.7UF M
CD63 24109333 CERAMIC CHIP CK73B 25V 33000PFK
CD64 24109332 CERAMIC CHIP, 50V B 3300PF K
CD86 24797100 ELECTROLYTIC, 50V 10UF M
CD88 24797100 ELECTROLYTIC, 50V 10UF M
CD90 24797100 ELECTROLYTIC, 50V 10UF M
CD91 24797100 ELECTROLYTIC, 50V 10UF M
CG01 24794100 ELECTROLYTIC, 16V 10UF M
CG02 24092730 CERAMIC CHIP, 16V B 0.1UF K
CG03 24794100 ELECTROLYTIC, 16V 10UF M
CG04 24109123 CERAMIC CHIP CK73B 50V 12000PF K
CG05 24092730 CERAMIC CHIP, 16V B 0.1UF K
CG06 24797479 ELECTROLYTIC, 50V 4.7UF M
CG07 24794100 ELECTROLYTIC, 16V 10UF M
CG08 24794100 ELECTROLYTIC, 16V 10UF M
CG09 24797479 ELECTROLYTIC, 50V 4.7UF M
CG10 24794101 ELECTROLYTIC, 16V 100UF M
CG11 24794100 ELECTROLYTIC, 16V 10UF M
CG12 24797479 ELECTROLYTIC, 50V 4.7UF M
CG13 24794100 ELECTROLYTIC, 16V 10UF M
CG14 24109272 CERAMIC CHIP, 50V B 2700PF K
CG15 24109473 CERAMIC CHIP, 25V B 0.047UF K
CG16 24704335 TA SOLID ELEC.CS15H 16V 3.3UF M
CG17 24794100 ELECTROLYTIC, 16V 10UF M
CG18 24088094 CHIP TA SOLID, 20V 10UF M B2-CAS
CG19 24797010 ELECTROLYTIC, 50V 1UF M
CG22 24109223 CERAMIC CHIP, 25V B 0.022UF K
CG23 24109472 CERAMIC CHIP, 50V B 4700PF K
CG24 24794100 ELECTROLYTIC, 16V 10UF M
CG25 24092730 CERAMIC CHIP, 16V B 0.1UF K
CG26 24109472 CERAMIC CHIP, 50V B 4700PF K
CG27 24794100 ELECTROLYTIC, 16V 10UF M
CG28 24794100 ELECTROLYTIC, 16V 10UF M
CG29 24092730 CERAMIC CHIP, 16V B 0.1UF K
CG30 24794100 ELECTROLYTIC, 16V 10UF M
CG31 24794100 ELECTROLYTIC, 16V 10UF M
CG32 24794100 ELECTROLYTIC, 16V 10UF M
CG33 24794100 ELECTROLYTIC, 16V 10UF M
CG40 24109562 CERAMIC CHIP, 50V B 5600PF K
CI01 24109103 CERAMIC CHIP, 50V B 0.01UF K
CI02 24109103 CERAMIC CHIP, 50V B 0.01UF K
CI03 24109103 CERAMIC CHIP, 50V B 0.01UF K
CI04 24109103 CERAMIC CHIP, 50V B 0.01UF K
CI05 24109103 CERAMIC CHIP, 50V B 0.01UF K
CI07 24109103 CERAMIC CHIP, 50V B 0.01UF K
CI08 24797010 ELECTROLYTIC, 50V 1UF M
CI09 24105470 CERAMIC CHIP, 50V CH 47PF J
CI10 24105180 CERAMIC CHIP, 50V CH 18PF J
CI11 24105270 CERAMIC CHIP, 50V CH 27PF J
CI12 24797478 ELECTROLYTIC, 50V 0.47UF M
CI13 24109102 CERAMIC CHIP, 50V B 1000PF K
CI14 24105470 CERAMIC CHIP, 50V CH 47PF J
CI15 24105390 CERAMIC CHIP, 50V CH 39PF J
CI16 24109103 CERAMIC CHIP, 50V B 0.01UF K
CI17 24092726 CERAMIC CHIP CK733B 16V 2,200,000PFK
CI18 24105181 CERAMIC CHIP, 50V CH 180PF J
CI21 24109103 CERAMIC CHIP, 50V B 0.01UF K
CI23 24109103 CERAMIC CHIP, 50V B 0.01UF K
CI25 24105240 CERAMIC CHIP, 50V CH 24PF J
CI51 24797220 ELECTROLYTIC, 50V 22UF M
CI52 24794101 ELECTROLYTIC, 16V 100UF M
CI53 24797339 ELECTROLYTIO CE04G, 50V 3.3UF M
CM51 24539104 PLASTIC FILM, 50V 0.1UF J
CM52 24105331 CERAMIC CHIP, 50V CH 330PF J
CM58 24539104 PLASTIC FILM, 50V 0.1UF J
CR01 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CR02 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CR03 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CS02 24797229 ELECTROLYTIC, 50V 2.2UF M
CS04 24797229 ELECTROLYTIC, 50V 2.2UF M
CS05 24797100 ELECTROLYTIC, 50V 10UF M
CS06 24797100 ELECTROLYTIC, 50V 10UF M
CS14 24797229 ELECTROLYTIC, 50V 2.2UF M
CS16 24797229 ELECTROLYTIC, 50V 2.2UF M
CS25 24797229 ELECTROLYTIC, 50V 2.2UF M
CS26 24797229 ELECTROLYTIC, 50V 2.2UF M
CS40 24797010 ELECTROLYTIC, 50V 1UF M
CS42 24797010 ELECTROLYTIC, 50V 1UF M
CS43 24105331 CERAMIC CHIP, 50V CH 330PF J
CS44 24105331 CERAMIC CHIP, 50V CH 330PF J
CS45 24109331 CERAMIC CHIP, 50V B 330PF K
CS46 24109331 CERAMIC CHIP, 50V B 330PF K
CS47 24105331 CERAMIC CHIP, 50V CH 330PF J
CS48 24105331 CERAMIC CHIP, 50V CH 330PF J
CS49 24105331 CERAMIC CHIP, 50V CH 330PF J
CS60 24105331 CERAMIC CHIP, 50V CH 330PF J
CS61 24109102 CERAMIC CHIP, 50V B 1000PF K
CS62 24109102 CERAMIC CHIP, 50V B 1000PF K
CS70 24794220 ELECTROLYTIC, 16V 22UF M
CS71 24794220 ELECTROLYTIC, 16V 22UF M
CS115 24797010 ELECTROLYTIC, 50V 1UF M
CS116 24797010 ELECTROLYTIC, 50V 1UF M
CS118 24794470 ELECTROLYTIC, 16V 47UF M
CS120 24797010 ELECTROLYTIC, 50V 1UF M
CV03 24206108 ELECTROLYTIC 04W, 50V 0.1UF M 7L 3A
CV05 24109103 CERAMIC CHIP, 50V B 0.01UF K
CV09 24503041 PLASTIC FILM , 63V 0.1UF J
CV13 24206108 ELECTROLYTIC 04W, 50V 0.1UF M 7L 3A
CV15 24109103 CERAMIC CHIP, 50V B 0.01UF K
CV24 24109473 CERAMIC CHIP, 25V B 0.047UF K
CV25 24794220 ELECTROLYTIC, 16V 22UF M
CV27 24092730 CERAMIC CHIP, 16V B 0.1UF K
CV29 24109103 CERAMIC CHIP, 50V B 0.01UF K
CV31 24092730 CERAMIC CHIP, 16V B 0.1UF K
CV38 24763471 ELECTROLYTIC, 16V 470UF M
CV39 24109103 CERAMIC CHIP, 50V B 0.01UF K
CV41 24092730 CERAMIC CHIP, 16V B 0.1UF K
CV61 24762471 ELECTROLYTIC, 04G 10V 470UF M
CZ01 24794101 ELECTROLYTIC, 16V 100UF M
CZ02 24109103 CERAMIC CHIP, 50V B 0.01UF K
CZ03 24794100 ELECTROLYTIC, 16V 10UF M
CZ04 24105181 CERAMIC CHIP, 50V CH 180PF J
CZ05 24105680 CERAMIC CHIP, 50V CH 68PF J
CZ06 24105330 CERAMIC CHIP, 50V CH 33PF J
CZ08 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ09 24109103 CERAMIC CHIP, 50V B 0.01UF K
CZ10 24794101 ELECTROLYTIC, 16V 100UF M
CZ12 24105101 CERAMIC CHIP, 50V CH 100PF J
CZ13 24105121 CERAMIC CHIP, 50V CH 120PF J
CZ14 24105151 CERAMIC CHIP, 50V CH 150PF J
CZ15 #1 24092442 CERAMIC CHIP, 16V F 0.47UF Z
CZ16 #1 24109103 CERAMIC CHIP, 50V B 0.01UF K
CZ17 #1 24109103 CERAMIC CHIP, 50V B 0.01UF K
CZ19 #1 24108181 CERAMIC CHIP, 50V SL 180PF J
CZ20 #1 24109103 CERAMIC CHIP, 50V B 0.01UF K
CZ21 #1 24109122 CERAMIC CHIP, 50V B 1200PF K
CZ22 #1 24794100 ELECTROLYTIC, 16V 10UF M
CZ23 #1 24109103 CERAMIC CHIP, 50V B 0.01UF K
CZ24 #1 24109103 CERAMIC CHIP, 50V B 0.01UF K
CZ25 #1 24794100 ELECTROLYTIC, 16V 10UF M
CZ26 #1 24109103 CERAMIC CHIP, 50V B 0.01UF K
CZ27 #1 24109103 CERAMIC CHIP, 50V B 0.01UF K

Location Parts No. Description
No.
Location Parts No. Description
No.
- 20 -
CZ28 #1 24109103 CERAMIC CHIP, 50V B 0.01UF K
CZ29 #1 24109103 CERAMIC CHIP, 50V B 0.01UF K
CZ30 #1 24794100 ELECTROLYTIC, 16V 10UF M
CZ31 24092730 CERAMIC CHIP, 16V B 0.1UF K
CZ32 #1 24109103 CERAMIC CHIP, 50V B 0.01UF K
CZ33 #1 24794100 ELECTROLYTIC, 16V 10UF M
CZ38 #1 24794100 ELECTROLYTIC, 16V 10UF M
CZ41 #1 24108470 CERAMIC CHIP, 50V SL 47PF J
CZ42 #1 24108470 CERAMIC CHIP, 50V SL 47PF J
CZ45 #1 24108100 CERAMIC CHIP, 50V SL 10PF D
CZ57 24105181 CERAMIC CHIP, 50V CH 180PF J
CZ58 24105560 CERAMIC CHIP, 50V CH 56PF J
CZ96 24105270 CERAMIC CHIP, 50V CH 27PF J
CZ250 #2 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ350 #2 24792101 ELECTROLYTIC CE04G, 6.3V 100UF M
CZ360 #2 24792101 ELECTROLYTIC CE04G, 6.3V 100UF M
CZ370 #2 24792101 ELECTROLYTIC CE04G, 6.3V 100UF M
CZ380 #2 24792101 ELECTROLYTIC CE04G, 6.3V 100UF M
CZ390 #2 24792101 ELECTROLYTIC CE04G, 6.3V 100UF M
CZ400 #2 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ410 #2 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ420 #2 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ430 #2 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ440 #2 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ450 #2 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ460 #2 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ470 #2 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ480 #2 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ490 #2 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ500 #2 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ510 #2 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ520 #2 24794100 ELECTROLYTIC, 16V 10UF M
CZ530 #2 24092730 CERAMIC CHIP, 16V B 0.1UF K
CZ540 #2 24092730 CERAMIC CHIP, 16V B 0.1UF K
CZ610 #2 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ620 #2 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ630 #2 24092730 CERAMIC CHIP, 16V B 0.1UF K
CZ640 #2 24105101 CERAMIC CHIP, 50V CH 100PF J
CZ650 #2 24092573 CERAMIC CHIP, 16V B 0.47UF K
CZ660 #2 24092730 CERAMIC CHIP, 16V B 0.1UF K
CZ670 #2 24092730 CERAMIC CHIP, 16V B 0.1UF K
CZ680 #2 24092730 CERAMIC CHIP, 16V B 0.1UF K
CZ690 #2 24092730 CERAMIC CHIP, 16V B 0.1UF K
CZ700 #2 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ710 #2 24092730 CERAMIC CHIP, 16V B 0.1UF K
CZ720 #2 24092730 CERAMIC CHIP, 16V B 0.1UF K
CZ730 #2 24092730 CERAMIC CHIP, 16V B 0.1UF K
CZ740 #2 24092730 CERAMIC CHIP, 16V B 0.1UF K
CZ750 #2 24092730 CERAMIC CHIP, 16V B 0.1UF K
CZ760 #2 24092573 CERAMIC CHIP, 16V B 0.47UF K
CZ770 24092730 CERAMIC CHIP, 16V B 0.1UF K
CZ830 #2 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ840 #2 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ970 #2 24794101 ELECTROLYTIC, 16V 100UF M
CZ980 #2 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ990 #2 24100104 CERAMIC CHIP, 25V F 0.1UF Z
RESISTORS
R101 24553223 OXIDE METAL FILM, 1W 22K OHM J
R203 24011474 CHIP, METAL FILM, 1/20W 470K OHM J
R204 24011182 CHIP, METAL FILM, 1/20W 1.8K OHM J
R205 24366152 CARBON FILM, 1/6W 1.5K OHM J
R206 24011222 CHIP, METAL FILM, 1/20W 2.2K OHM J
R207 24011101 CHIP, METAL FILM, 1/20W 100 OHM J
R208 24011101 CHIP, METAL FILM, 1/20W 100 OHM J
R209 24011101 CHIP, METAL FILM, 1/20W 100 OHM J
R216 24366223 CARBON FILM, 1/6W 22K OHM J
R219 24366223 CARBON FILM, 1/6W 22K OHM J
R227 24366682 CARBON FILM, 1/6W 6.8K OHM J
R228 24366333 CARBON FILM, 1/6W 33K OHM J
R238 24011473 CHIP, METAL FILM, 1/20W 47K OHM J
R239 24011224 CHIP, METAL FILM, 1/20W 220K OHM J
R240 24011562 CHIP, METAL FILM, 1/20W 5.6K OHM J
R241 24011682 CHIP, METAL FILM, 1/20W 6.8K OHM J
R245 24366104 CARBON FILM, 1/6W 100K OHM J
R261 24011472 CHIP, METAL FILM, 1/20W 4.7K OHM J
R262 24011102 CHIP, METAL FILM, 1/20W 1K OHM J
R263 24011472 CHIP, METAL FILM, 1/20W 4.7K OHM J
R264 24011102 CHIP, METAL FILM, 1/20W 1K OHM J
R265 24011472 CHIP, METAL FILM, 1/20W 4.7K OHM J
R266 24011102 CHIP, METAL FILM, 1/20W 1K OHM J
R271 24366471 CARBON FILM, 1/6W 470 OHM J
R272 24366222 CARBON FILM, 1/6W 2.2K OHM J
R301 24011272 CHIP, 1/20W 2.7K OHM J
R303 24321109 OXIDE METAL FILM, 1/2W 1 OHM J
R304 24366623 CARBON FILM, 1/6W 62K OHM J
R305 24322828 OXIDE METAL FILM, 1W 0.82 OHM J
R306 24366104 CARBON FILM, 1/6W 100K OHM J
R307 24366684 CARBON FILM, 1/6W 680K OHM J
R308 24382821 OXIDE METAL FILM, 1W 82 OHM J
R312 24366153 CARBON FILM, 1/6W 15K OHM J
R313 24011104 CHIP, METAL FILM, 1/20W 100K OHM J
R314 24366104 CARBON FILM, 1/6W 100K OHM J
R315 24011104 CHIP, METAL FILM, 1/20W 100K OHM J
R316 24366154 CARBON FILM, 1/6W 150K OHM J
R317 24011102 CHIP, METAL FILM, 1/20W 1K OHM J
R318 24011473 CHIP, METAL FILM, 1/20W 47K OHM J
R327 24339479 OXIDE METAL FILM, 2W 4.7 OHM J
R328 24366684 CARBON FILM, 1/6W 680K OHM J
R336 24383151 OXIDE METAL FILM, 2W 150 OHM J
R360 24011104 CHIP, METAL FILM, 1/20W 100K OHM J
R361 24011473 CHIP, METAL FILM, 1/20W 47K OHM J
R370 24321109 OXIDE METAL FILM, 1/2W 1 OHM J
R371 24011103 CHIP, METAL FILM, 1/20W 10K OHM J
R372 24011392 CHIP, 1/20W 3.9K OHM J
R373 24011102 CHIP, METAL FILM, 1/20W 1K OHM J
R374 24366183 CARBON FILM, 1/6W 18K OHM J
R401 24011391 CHIP, 1/20W 390 OHM J
R402 24382682 OXIDE METAL FILM, 1W 6.8K OHM J
R403 24011622 CHIP, METAL FILM, 1/20W 6.2K OHM J
R405 24382682 OXIDE METAL FILM, 1W 6.8K OHM J
R406 24366273 CARBON FILM, 1/6W 27K OHM J
R407 24011103 CHIP, METAL FILM, 1/20W 10K OHM J
R408 24011472 CHIP, METAL FILM, 1/20W 4.7K OHM J
R410 24011271 CHIP, 1/20W 270 OHM J
R411 24366561 CARBON FILM, 1/6W 560 OHM J
R415 24553272 OXIDE METAL FILM, 1W 2.7K OHM J
R416 24510332 CERAMIC COVERED, 5W 3.3K OHM J
R418 24383181 OXIDE METAL FILM, 2W 180 OHM J
R429 24366104 CARBON FILM, 1/6W 100K OHM J
R430 24366102 CARBON FILM, 1/6W 1K OHM J
R431 24011103 CHIP, METAL FILM, 1/20W 10K OHM J
R432 24366202 CARBON FILM, 1/6W 2K OHM J
R441 24532102 FUSIBLE, 1W 1K OHM J
R443 24382153 OXIDE METAL FILM, 1W 15K OHM J
R450 24011103 CHIP, METAL FILM, 1/20W 10K OHM J
R455 24011103 CHIP, METAL FILM, 1/20W 10K OHM J
R457 24011473 CHIP, METAL FILM, 1/20W 47K OHM J
R458 24011104 CHIP, METAL FILM, 1/20W 100K OHM J
R460 24366562 CARBON FILM, 1/6W 5.6K OHM J
R461 24366182 CARBON FILM, 1/6W 1.8K OHM J
R463 24322399 OXIDE METAL FILM, 1W 3.9 OHM J