total sheds 6x6ft DOG KENNEL User manual

*Actual nished dimension area 74.3”x 71.4”
Kennel with Run Area
Requires a minimum build area.*
Please see details below.
6x6ft
Fully Built Size
The kennel is slightly
larger when fully built
to cater for the
nishing strips and
complete unit
(188.82cm)
74.3” Front Width
(184.7cm)
71.4” Depth
6x6ft
DOG KENNEL
Ready to Build Dog Kennel
Total Sheds
28 Charles Street,
Willenhall, WV13 1HG
Tel: [phone]
Email: [email protected]o.uk
© Copyright Total Sheds
Order Supplied with:
4.0 x 70mm
Easy Drill Screws
SHEDS • SUMMER HOUSES • KENNELS
ASSEMBLY MANUAL
Pressure Treated
Tanalised Timber for
Longer Lasting Life!
DELIVERED FLAT PACKED
EASYTO INSTALL SECTIONS...

Thank you for purchasing your
Dog Kennel from Total Sheds.
All of our Kennels are made from only the nest
selected timber which are (Tanalised), specially
pressure treated for a longer and lasting durable
life span to the elements.
Each Kennel is carefully prepared in sections.
Making the assembly process as easy as possible for you.
Please follow our simple step-by-step guide and have your
dogs new home built in no time!
1x Kennel Floor
Page 3 Page 4 & 5
Page 3
Total Sheds •28 Charles Street,
Willenhall, WV13 1HG • Tel: [phone]
Email: [email protected]o.uk
www.totalsheds.co.uk
Manual Page 2
Pressure Treated Timber
DELIVERED FLAT PACKED
EASYTO INSTALL SECTIONS...
Tools Required to Assemble:
2 Persons Required
PLEASE NOTE: Use extreme caution when using any tools. Always wear
safety gear where necessary. It is advisable that at least 2 or more
persons assemble the kennel for health and safety purpose. We are not
responsible for any injuries caused whilst assembling this kennel.
6x6ft Dog Kennel Check List
Your delivery should contain the following:
STANLEY
KNIFE
2x Side Blocks
Page 6
1x Side Panel Right
1x Front Left
Page 5Page 4
2x Back Panels
Page 7
6x Corner Strips
Page 7
1x Front Right
1x Pop Hole
Page 6
Page 9Page 9
8x Felt Strips
Page 8
3x 7ft Roof Felts2x Roofs Panels
Contents are in assembling order.
HAMMER DRILL
DRIVER
1x Side Panel Left
Supplied with 4.0 x 70mm
EASY DRILL SCREWS
© Sheds (Midlands) Limited 2021

Manual Page 3
www.totalsheds.co.uk
Assembly Manual
Page 1 of 3
KENNEL FLOOR BASE
Set the base for the kennel
oor to build on.
ATTACH FLOOR BLOCK 1
Screw in to left of oor side as shown.
SET THE KENNEL FOUNDATION FLOOR BLOCK x1
Place oor down into the required
position/area. (7x7sqft recommended)
TIPS & ADVICE: It is always good to position your
kennel on a solid foundation.
Slabs or Concrete areas are ideal.
FIX SIDE POSTTO FLOOR
EDGE WITH LARGE SCREWS
STEP • 1
63mm 45mm
38mm
34mm
12mm
= Drill Points using
screws provided as shown
Floor Block x1
STEP • 2
Floor Block
63mm x 38mm
69.5” Length
(895.3mm)
(1765.3mm)
35.25” Width
x3
4.0 x 70mm
DRILL
DRIVER
© Sheds (Midlands) Limited 2021 • 6x6ft Dog Kennel

63mm
Back Panel
Kennel Floor
DO NOT SCREW DOWN THE
PANELS TO FLOOR JUST YET!
Screw only the vertical panels to create a
standing frame rst, allowing room for adjustments.
Side Block
Manual Page 4
www.totalsheds.co.uk
Assembly Manual
Page 1 of 3
Position Back Panel 1
Set within the oor planks, sitting just o
the rear edge.
Position Left Side Panel
Now place the Left Side Panel ush
against the Back Panel Post.
ATTACH BACK PANEL 1 of 2 LEFT SIDE PANEL
STEP • 3 STEP • 4
(895.5mm)
45.25” Height
(1149.35mm)
35.25” Width
(1790.7mm)
(1790.7mm)
46.5” Height
(1181.1mm)
47” Height
(1193.8mm)
70.5” Width
70.5” Width
3/4
10 Planks of Shiplap
= Drill Points using
screws provided as shown
DRILL
DRIVER
KENNEL FLOOR
LEFT SIDE PANEL
KENNEL FLOOR
KENNEL BACK
BACK PANEL
Set side panel left
against back panel post
as shown on this image.
SIDE PANEL •
• BACK PANEL
• FLOOR
x3
4.0 x 70mm
© Sheds (Midlands) Limited 2021 • 6x6ft Dog Kennel

Manual Page 5
www.totalsheds.co.uk
Assembly Manual
Page 1 of 3
Attach Back Panel 2
Use the 2nd Floor Block to raise the back
panel height then screw against 1st panel side.
Attach Right Side Panel
Now attach the Right Side Panel by placing
against 2nd back panel side as below.
ATTACH BACK PANEL 2 of 2 RIGHT SIDE PANEL
STEP • 5 STEP • 6
(895.5mm)
45.25” Height
(1149.35mm)
35.25” Width
(1790.7mm)
46.5” Height
(1181.1mm)
47” Height
(1193.8mm)
70.5” Width
70.5” Width
3/4
10 Planks of Shiplap
(1790.7mm)
DRILL
DRIVER
DRILL
DRIVER
Using the Floor Block Posts, elevate the 2nd
back panel and screw in sides to secure againsts
the 1st back panel side post as shown here.
Using the Floor Block Posts, elevate the right side
panel and screw in sides to secure againsts
the 2nd back panel side post as shown.
Position the 2nd back
panel in place as shown on
diagram below. The back panel
2 must be the same height as the 1st
back panel which is 63mm from the
ground to back panel frame bottom.
BACK PANEL 2
RIGHT PANEL
= Drill Points using
screws provided as shown
x3
4.0 x 70mm
= Drill Points using
screws provided as shown
x3
4.0 x 70mm
© Sheds (Midlands) Limited 2021 • 6x6ft Dog Kennel

Front Door Panel
Now set the 1st of the front panels.
Position the solid door panel like below.
ATTACH BACK FRONT PANEL A
DRILL
DRIVER
FRONT PANEL A
46” Height
(1168.4mm)
(895.35mm)
35.25” Width
Place Pop Hole Panel
Set within the oor planks sitting ush with
front and rear panel edges and oor.
POP HOLE
44.5” Height
(1130.3mm)
66.8” Width
(1699mm)
46.25” Height
(1174.7mm)
DRILL
DRIVER
POP HOLE
Manual Page 6
www.totalsheds.co.uk
STEP • 7 STEP • 8
= Drill Points using
screws provided as shown
x6
4.0 x 70mm
= Drill Points using
screws provided as shown
x3
4.0 x 70mm
© Sheds (Midlands) Limited 2021 • 6x6ft Dog Kennel

Manual Page 7
www.totalsheds.co.uk
Assembly Manual
Page 1 of 3
Front Mesh Panel
Now place the front right panel between
left front and right side panel edges as shown.
Attach Corner Strips
Now nish off the panels edges with the
corner strips provided.
ATTACH BACK FRONT PANEL A SIDE STRIPS
STEP • 9 STEP • 10
(1174.75mm)
(45mm)
46.25” Length
1.77” Width
x6
DRILL
DRIVER
46.25” Height
(1174.75mm)
21”
1/2
1 Planks of Shiplap
(895.35mm)
35.25” Width
Door Height
Door Width
21.5”
37.25”
DRILL
DRIVER
FRONT PANEL B
= Drill Points using
screws provided as shown
x6
4.0 x 70mm
= Drill Points using
screws provided as shown
x12
4.0 x 70mm
© Sheds (Midlands) Limited 2021 • 6x6ft Dog Kennel

Manual Page 8
www.totalsheds.co.uk
Assembly Manual
Page 1 of 3
1st Roof Section
Now place the 1st of the 2 roof panels
as shown in the diagram below.
PLACE ROOF SECTION 1 PLACE ROOF SECTION 2
STEP • 11 STEP • 12
2nd Roof Section
Now place the 2nd roof panel as shown
in the diagram below.
DRILL
DRIVER
DRILL
DRIVER
Now secure down the roof and the base
adjusting where need be to make nal
structure safe & solid.
Remember to drill the panels down to the
oor at this stage as all the build sections
are together now.
Secure roof panels by screwing them
down to kennel framework as shown.
72” Length
(895.3mm)
(1765.3mm)
35.25” Width
72” Length
(895.3mm)
(1765.3mm)
35.25” Width
= Drill Points using
screws provided as shown
x4
4.0 x 70mm
= Drill Points using
screws provided as shown
x4
4.0 x 70mm
© Sheds (Midlands) Limited 2021 • 6x6ft Dog Kennel

STANLEY
KNIFE
= Drill Points using
screws provided as shown
Manual Page 9
www.totalsheds.co.uk
Assembly Manual
Page 1 of 3
APPLY ROOF FELT SHEETS x3
Finishing Touches!
To hide the tacked felt edges add the felt
strips along the top edge of roof as shown.
FINISH OFF WITH FELT STRIPS
You may use optional Diamond Cap to cover felt strip join
CONGRATULATIONS - YOUR DONE !
STEP • 13 STEP • 14
40kg Mineral Felt Roof
You will be provided with 3 lengths of high
quality roof felt. Start with lower end of roof rst.
x8
(1879.6mm)
(120mm)
74” Length
4.7” Height
HAMMER
DRILL
DRIVER
TACKS PROVIDED
Proceed with 1st layer at the
rear lowest point of roof, then
overlay the other
2 sections.
After cutting away the excess felt,
neatly fold over the edges and
secure each section down by tacking
them to the kennel sides.
PROTECT YOUR KENNEL AGAINST
THE RAIN & ELEMENTS.
Create a neat and tidy roof nish
hiding the rough edges and
tacks. Measure the sides for a
perfect cut and nish!
*Sections may come longer than
required. Please saw down.
Carefully check all the panels are
tted well and the kennel is secure
and stable.
You are almost done
building your kennel!
1st
2nd
3rd
1st Sheet at rear of roof
2nd Sheet higher above
3rd sheet on top front
Trim edges with 3” over
Fold & tack edges neatly
A
B
C
D
E
Neat & tidy nished roof
x3
(2133.6mm)
1m (1000mm)
(7ft) 84” Length
39” Width
© Sheds (Midlands) Limited 2021 • 6x6ft Dog Kennel