total sheds Pent Shed 12x4ft User manual

Ready To Build - 4ft Range
Pent Shed Assembly Manual
Pressure Treated Tanalised Timber for Longer Lasting Life!
Version 1.4
Thank you for purchasing your Total Shed.
All of our sheds are made from only the nest selected timber which are
(Tanalised), specially pressure treated for a longer and lasting durable life
span to the elements.
Each shed is carefully packed and delivered on a pallet
ready to be assembled.
FEATURES NEW FLEXIBLE,
INTER-CHANGEABLE DESIGN
FORYOUR INDIVIDUAL STYLE.
DELIVERED FLAT PACKED IN
EASY TO INSTALL SECTIONS
2 Persons Recommended for Assembling Shed
PLEASE NOTE: Use extreme caution when using any tools. Always wear safety gear where
necessary. It is advisable that at least 2 or more persons assemble the shed for health and safety
purposes. We are not responsible for any injuries caused whilst assembling this shed.
Ready to Build Shed
Includes 4x4ft to 20x4ft Instructions
Featured Build of the Pent 12x4ft Shed
DRILL DRIVER HAMMER HAND SAW STANLEY KNIFE
Tools Required:
www.totalsheds.co.uk
© Sheds (Midlands) Limited 2021
Total Sheds
Unit 1 Park Lane,
West Bromwich, B21 8LE
Tel: [phone]
Email: [e-mail]

PRE-ASSEMBLY PRE-ASSEMBLY
01
Unpack all of the components and check
that you have all the parts required.
Please use the checklist on previous page.
Carefully dispose of the delivery pallet
and any excess timber.
Advisable: The underside of the oor must
be treated with a quality wood preserver.
Recommended: Paint shed
in an oil based treatment to
prevent water ingress into
the timber. Also silicon your
windows (Must silicon inside &
outside) to prevent rain water
seeping through the gaps
between glass and the timber.
SHED FLOOR: Setting Shed Base
Unpacking your Parts
SET THE SHED FOUNDATION This Manuals Diagrams are based on the
12ft x 4ft Pent Shed
+
+
+
+
+ +
++
+ +
+ +
+ ++ +
+ +
+
+ +



























4x4ft
4x4ft
4x4ft
4x4ft
4x4ft
4x4ft
4x4ft
4x4ft
4x4ft
4x4ft
4x4ft
4x4ft
4x4ft
4x4ft
4x4ft
4x4ft
4x4ft
4x4ft
4x4ft
4x4ft
4x4ft
4x4ft
4x4ft
4x4ft
4x4ft
4x4ft
2x4ft 2x4ft 2x4ft 2x4ft = Drill Points using
screws provided as shown
x3
x2
4.0 x 70mm
Per Floor Section
PLEASE NOTE: All Shed Floors have the 4ft x 4ft Floor on the Left.
1a. Place the Floor panels with the Frame work pointing forwards (as shown in below)
then screw together using screws provided at the end of the bearer points.
1b. Check that all oor sections are securely attached and in a straight line to avoid any problems
later on the build stage.
Use a Spirit Level for accuracy
1c. Secure the oor sections together by
screwing the oor bearers at each end where
they meet as shown in diagram 1c.
4ft Floor
1c
4ft Floor
4ft Floor
© Sheds (Midlands) Limited 2021 www.totalsheds.co.uk

STEP • 2 STEP • 3
02
IMPORTANT
All Sheds With 3 or
More Floor Pannels
have the smallest Floor
Panel on the End.
As shown on this diagram.
FLOOR & BLOCK ENDS
= Drill Points using
screws provided as shown
4ft BLANK
4FT RIGHT SIDE PANEL
4ft LEFT SIDE PANEL
Place rst panel againts
far Left of shed oor
as shown.
(4ft wide blank panel)
3a. Place the 4ft Blank Panel against the far side of the
shed oor. Make sure the panel stands rmly on the
Heavy Duty Post (Floor Block).
3b. Now prepare the 4ft Blank Panel in order to create an
‘L’ shape in the corner with the two panels.
3c. DO NOT x the panels at this stage to the oor. This is
because you need to leave room for adjustements in the
nal stages of the shed build.
2a. In your kit you should nd 2x 4ft blocks.
These will act as your oor block.
2b. Fix together by screwing the Floor.
Blocks at each end as shown. Use the screws
provided and make sure the ends are xed
securely. 2 screws on each Floor Block will
suce. (Repeat for other side)
Add the Floor Block Ends
(Heavy Duty Posts)
= Drill Points using
screws provided as shown
x3
x2
4.0 x 70mm
Per Floor Block
2b
2b
FLOOR BLOCKS
© Sheds (Midlands) Limited 2021 www.totalsheds.co.uk

STEP • 4 STEP • 5
03
= Drill Points using
screws provided as shown
= Drill Points using
screws provided as shown
x3
4.0 x 70mm
Per Panel Edge
x3
4.0 x 70mm
Per Panel Edge
4ft REAR PANEL
REAR PANEL
Place panel againts far the
back of shed oor
as shown.
(4ft wide Blank Panel)
4b
REAR PANEL
REAR PANEL
Fix 4ft Wide Blank
Sections. Create a Corner
for Balance.
4a. Place a 4ft Blank
Panel side as shown
below. Repeat this step
for all larger Sheds. Please
use reference on left
for additional sections
required according to your
shed size.
4b. Screw the Blank Panel
alongside the framework
as shown in Diagram 4b.
INFORMATION
Not all Summer Sheds
will have the same panel
arrangment. Please Ensure
that the 4ft Panels are
central for all builds.
5a. Place the 4ft Blank Panel side against the corner of the back 4ft oor as shown making sure
the panel is sitting rmly on the shed oor and the side meeting the framework of the back 4ft
Blank Panel.
5b. Fix the panels
together with
screws as shown
in diagram. You
may require some
supports to keep
the frame upright
whilst building
longer sheds.
© Sheds (Midlands) Limited 2021 www.totalsheds.co.uk

STEP • 6 STEP • 7
04
= Drill Points using
screws provided as shown
x3
x3
4.0 x 70mm
Per Panel Edge
4ft RIGHT SIDE PANEL
4ft RIGHT SIDE PANEL
Attach 4ft Blank Section
to the Right Side Wall
6a. Place the 4ft Blank Panel at the far RIGHT of the shed, connecting it with the rear sections.
(Same placement as the right side 4ft panel just on the other side).
DO NOT screw the standing panels
down to the oor just yet. Leave
room for adjustments when the nal
frame is tted.
x3
x3
4.0 x 70mm
Per Panel Edge
FRONT DOOR PANEL
Attach Door Front Panel
(4ft Door Panel)
= Drill Points using
screws provided as shown
FRONT DOOR PANEL
7a. Now place the 4ft Door Panel as shown. Fix together with screws to the Left side panel
framework (The side that comes in contact with the 4ft Blank Panel).
x3
4.0 x 70mm
Per Panel Edge
© Sheds (Midlands) Limited 2021 www.totalsheds.co.uk

STEP • 8 STEP • 9
05
FRONT WINDOW
PANEL
Attach First Front Panel
(4ft Window Panel)
FRONT WINDOW
PANEL
Attach Front Panel
(4ft Window Panel)
4ft FRONT WINDOW PANEL
= Drill Points using
screws provided as shown
x3
4.0 x 70mm
Per Window Panel
DO NOT screw the standing panels
down to the oor just yet. Leave room for
adjustments when the nal frame is tted.
8a. Start back from the Right side placing the 4ft
Window Panel as shown. Fix together with screws
to the right side panel framework.
4ft FRONT WINDOW PANEL
= Drill Points using
screws provided as shown
x3
4.0 x 70mm
Per Window Panel
9a. Repeat the previous stage until all Window Panels have been secured in place. Once all of
the Wall panels have been secured, you can now screw the frame down to the base. Take time to
ensure that the walls are square.
© Sheds (Midlands) Limited 2021 www.totalsheds.co.uk

STEP • 10 STEP •11
06
SIDE PENT ANGLE TOPS
Now attach all the Side
Tops of Pent Shed End
Panels. (Over the top of
both side panels).
SIDE PENT ANGE TOPS
= Drill Points using
screws provided as shown
x3
x2
4.0 x 70mm
Per Angle Top
10a. Now place the 4ft Slope on top of the Blank
Panels and use two 70mm screws to secure them
together, making sure that they are in line.
10b. Once the Pent Angle Top has been
constructed, use the screws to secure the
Angle Tops to the sides of the Shed.
PENT FRONT TOPS
Place the front tops of
shed.
= Drill Points using
screws provided as shown
x3
x2
4.0 x 70mm
Per Front Top
PENT FRONT TOPS
11a. Place the Pent Front Top sections in place. Adjust the panels so
that the tounge & groove are xed together in place correctly. Use a
hammer to lightly tap in to the grooves to create a perfect t.
11b. Attach the sections down by
screwing through the inner framework of
both panels.
© Sheds (Midlands) Limited 2021 www.totalsheds.co.uk

STEP • 12 STEP • 13
07
= Drill Points using
screws provided as shown
x3
x3
4.0 x 70mm
SIDE & CORNER STRIPS
SIDE & CORNER STRIPS
Hide the panel edges.
Cover the framework &
seams.
13a. Use all the Side/Corner Strips to nish
o the shed, by covering any exposed
framework and the panel joining seams.
13b. Use a 3mm Drill bit to prevent the wood
from splitting. Use the 70mm Screws to secure
these Strips to place. it will take 3x screws to
properly six the Strips to the Shed.
INFORMATION
The Corner Strips cover all panel edges. Remeber
to attach these to the exterior back panels too.
13a
PENT ROOF PANELS
Place First roof section.
Repeat for all Roof Panels
(2ft, 3ft, 4ft)
= Drill Points using
screws provided as shown
x3
x4
4.0 x 70mm
Per Roof Panel
PENT ROOF PANELS
12a. Place the 4ft Roof Panel in place. Repeat this stage for models as shown below. 4ft Roof
Panel will always be on the Left. Repeat until all Roof APanels are xed in place.
Per Corner Strip
© Sheds (Midlands) Limited 2021 www.totalsheds.co.uk

STEP • 14 STEP •15
08
CUTTING THE ROOF
FELT
Use the felt table to cut
your felt to the correct
size
14a. Use the Stanley knife to cut your felt into the correct size. Using the table below, nd the Build
size that you have and cut your felt down to achieve the size that you will need.
Example:
Pent Shed 12ft x 4ft
The 12 by 4 needs 2 sheets of felt. All at 13ft each.
CUTTING THE ROOF FELT
4ft (x2) 5ft (x3) 6ft (x3) 7ft (x4) 8ft (x5)
4ft 5ft 5ft 5ft 5ft 5ft
5ft 6ft 6ft 6ft 6ft 6ft
6ft 7ft 7ft 7ft 7ft 7ft
7ft 8ft 8ft 8ft 8ft 8ft
8ft 9ft 9ft 9ft 9ft 9ft
9ft 10ft 10ft 10ft 10ft 10ft
10 ft 11ft 11ft 11ft 11ft 11ft
11 ft 12ft 12ft 12ft 12ft 12ft
12 ft 13ft 13ft 13ft 13ft 13ft
13 ft 14ft 14ft 14ft 14ft 14ft
14 ft 15ft 15ft 15ft 15ft 15ft
15 ft 16ft 16ft 16ft 16ft 16ft
16 ft 17ft 17ft 17ft 17ft 17ft
17 ft 18ft 18ft 18ft 18ft 18ft
18 ft 19ft 19ft 19ft 19ft 19ft
19 ft 20ft 20ft 20ft 20ft 20ft
20 ft 21ft 21ft 21ft 21ft 21ft
Build Length
Build Depth
TACKS PROVIDED
ATTACH THE ROOF FELT
Use the felt lengths
provided.
15a. Apply the roof felt as shown. Apply lower levels rst to create
correct rain run o positions.
15b. Using a hammer, tack down the felt with the tacks provided in a
neat fashion.
15c. Trim down excess felt with a stanley knife. Remember to
overlay the 1st felt to avoid rain leaks.
15d. Tuck and fold edges neatly and tack in place to hide any
loose edges. Check that all areas are covered and there are no
holes to avoid any rain water getting through your felt roof.
ROOF FELT
3rd
© Sheds (Midlands) Limited 2021 www.totalsheds.co.uk

STEP • 16 STEP • 17
09
FELT STRIPS
ATTACH FELT STRIPS
Create the Final Roof
Edges. Final steps nish-
ing o the roof.
Per Felt Strip
DIAMOND CAPS
Add the Finishing
Touch. (Optional)
Timber is a naturally grown product and may shrink and warp when dried out, timber is a porous
material which can absorb water. Although all of our buildings come pressure treated we strongly
advise the building is re-treated with an oil/spirit based treatment inside and out to make the timber
water repellent and to preserve the quality and life of the product.
Congratulations
FINISHED!
= Drill Points using
screws provided as shown
x3
x2
4.0 x 38mm
16a. Using the felt strips provided cover the edges of the roofs and ends of the roof felt. You will
need to measure these and saw to t to your requirements and create the perfect roof nish as
shown below.
16b. Drill in the felt strips as shown on front and back of the shed to nish the roof o. Use the
framework of the roof blocks to screw the felt strips down to. The felt strips will give your shed a
neat nish for the roof and hide any overhang areas of the roof felt.
NOTE:
Location of the Felt Strips
16c. Felt Strips must be same height as roong
felt to allow rain water to run o. See Diagram on
the right.
© Sheds (Midlands) Limited 2021 www.totalsheds.co.uk
Total Sheds
Unit 1 Park Lane,
West Bromwich, B21 8LE
Tel: [phone]
Email: [e-mail]