Total TT101116 User manual

GLUE GUN
100W
totaltoolsworld
TOTAL TOOLS WORLD
TT101116,UTT101116,
TT101116-4,TT101116-6,
TT101116-8,TT101116-9,
TT101116S

Safety Regulations
Warning!
Do not open the casing!
Dangerous voltage is found
unprotected on some components
inside the product's casing; contact
with these may lead to electric shock.
•The product may only be repaired by
qualified service personnel.
•The product may not be taken apart
nor be changed.
•Do not place the product so that it may
fall down into water or another liquid.
Do not put any items containing water on
the product, for example a flower vase
or a soda can.
•Disconnect the plug when the Glue Gun
is not in use; let it cool off before storage.
•Check that the voltage that is indicated
on the mark sign corresponds with the
local power grid voltage.
•The Glue Gun is not a toy, do no let
children use it without supervision!
•Never leave the Glue Gun unattended
when it is turnedon.
•The Glue Gun is made for indoor usage;
protect it from water and dampness.
2

The following safety precautions
shall be followed to avoid the risk
of fire:
•Be careful when you use the Glue Gun
in spaces with inflammable material.
•Do not hold the Glue Gun over the
same spot for a long time.
•Do not use the Glue Gun in explosive
environments.
•Keep in mind that the heat can conduct
to inflammable material that is out of
sight.
•Place the Glue Gun on the holder after
use and let it cool off before storage.
•Do not leave the Glue Gun unattended
when the cord is connected to the wall
socket.
Warning!
The glue is very hot during usage. It may
cause burns on the skin.
Rinse immediately with cold water.
3

3
Description
1. Trigger 2. Nozzle
3. Cable 4. Glue stick
The Glue Gun is made for gluing
wood, paper and cardboard as well
as some plastic materials.
2
1
4
Usage
1. Connect the plug to the wall socket.
2. Place a glue stick in the opening on the
back of the gun as indicated in the
picture.
4. Press the trigger several times to feed
the glue stick forward.
5. Press the trigger to feed the glue forward
when it has started to melt.
6. Apply melted glue on the surfaces to be
joined together, and then press the glued
surfaces together for 15 seconds.
7. Unplug the plug after usage.
3. Push in the glue stick as far as possible.
4

Disposal
Follow local ordinances when
disposing of this product.
If you are unsure about how to dispose of
this product contact your municipality.
Technical data
Model No. TT101116 TT101116-6
(ISRAEL Plug)
TT101116-4
(IRAM Plug)
TT101116-9
(INMENTRO Plug)
TT101116-8
(BS Plug)
TT101116S
(SAA Plug)
Voltage 220-240V
Frequency 50/60Hz
Electricity consumption 100W
Diameter glue stick Φ11.2mm
Gluing Capacity 13-18g/min
Model No. UTT101116
Voltage 110-120V~
Frequency 50/60Hz
Electricity consumption 100W
Diameter glue stick Φ11.2mm(7/16˝)
Gluing Capacity 13-18g/min
Fig 2
When the glue stick will be used up, the
glue gun can’t work regularly, because
the trigger can’t push the glue stick (Fig 1).
At this time, you should place a new one
stick, so the new stick can push the
former one, the glue gun will work
regularly (Fig 2).
NOTE:
Fig 1
5

TT101116,UTT101116,
TT101116-4,TT101116-6,TT101116-8
TT101116-9,TT101116S Exploding view
6

TT101116,UTT101116,
TT101116-4,TT101116-6,TT101116-8
TT101116-9,TT101116S Spare part list
No. Part Description Qty
1 glue gun shells 1
2 cap of nozzle 1
3 Aluminum parts of heater 1
4 silicon sleeve 1
5 fix ring 1
6 plastic sleeve 1
7 silicon Rear retaining ring 1
8 Circlip 1
9 plastic stand 1
10 Silicon sleeve 2
11 tablet compressing 1
12 electric cable 1
13 Insulating paper 1
14 drag spring 1
15 heater 1
16 Conductive sheet 2
17 trigger 1
18 connecting rod 1
19 propeller 1
20 Internal wire 2
21 Heat shrinkable tube 2
7

100W
T0319.V03
MADE IN CHINA
www.totaltools.cn
TOTAL TOOLS CO., PTE. LTD.
GLUE GUN