Toto EGO TX115LEN User manual

SPECIFICATIONS
TX115LEN
S06157R
TOTO
415
max. 230
max.30
G1¼
46
G½
Ø42
48
154
119
25°
38~51
Ø60
Lavatory
CH
OPERATING CONDITIONS
ATTENTION
TROUBLESHOOTING
CHECK
POINT
Flow rate unsatisfactory 1 Remove and clean
Water leaks around the handle 2 Tighten
Handle is loose 3 Tighten
Plug cannot open and close 4 Tighten
Bodyswinging 5 Tighten
PROBLEM
SOLUTION
2. CONNECTING NUT
1. AERATOR
3. BOLT
4. BOLT
MAINTENANCE
Always wipe plated area with dry soft cloth, and sometimes
wipe it with cloth soaked in mild soap. R6
INSTALLATION
1.
Setting Bolt
Washer
Setting Nut
Packing
Faucet
2.
3.
Bottom
Position
OPEN
Position
Plug
Siphon
Packing Triangle
Packing
Nut
Pivot Rod
Packing
Bolt
Kick Box
Bolt
Pop-Up Clip
C
H
Ø35 Hole
Washer
To Cold Water Supply
To Hot
Water Supply
Lift rod
C
H
1. Water supply pressure : 0.05 ~ 0.75 MPa.
2. Ensure that water supply is clean ( No Sand, Dirt, Etc.).
Don’t use abrasive cleaning material such as; detergents
containing hydrochloric acids, thinner, polishing powder,
and nylon brush.
As the product model is constantly updated, the actual
product may not look the same as it shown in the diagram,
but the basic installation principles are the same.
1.
2.
5. SETING NUT
"EGO"SINGLE LEVER LAVATORY FAUCET
W/ 1¼"POP-UP WASTE

SPESIFIKASI
TX115LEN
S06157R
TOTO
415
max. 230
max.30
G1¼
46
G½
Ø42
48
154
119
25°
38~51
Ø60
Lavatory
CH
PENYELESAIAN MASALAH
2. CONNECTING NUT
1. AERATOR
3. BOLT
4. BOLT
R6
PEMASANGAN
1.
Setting Bolt
Washer
Setting Nut
Packing
Faucet
2.
3.
Bottom
Position
OPEN
Position
Plug
Siphon
Packing Triangle
Packing
Nut
Pivot Rod
Packing
Bolt
Kick Box
Bolt
Pop-Up Clip
C
H
Ø35 Hole
Washer
To Cold Water Supply
To Hot
Water Supply
Lift rod
C
H
5. SETING NUT
"EGO"SINGLE LEVER LAVATORY FAUCET
W/ 1¼"POP-UP WASTE
KONDISI OPERASIONAL
PEMELIHARAAN
Selalu bersihkan area yang berlapis krom dengan kain
lembut kering, dan sesekali bersihkan dengan kain yang
direndam dalam sabun yang dicampur air.
PERHATIAN
Jangan gunakan bahan pembersih yang bersifat abrasif
seperti deterjen yang mengandung asam klorida, tinner,
bubuk polishing dan sikat nilon.
Karena model produk terus mengalami pembaharuan,
aktual produk mungkin tidak sama dengan gambar, tapi
prinsip dasar pemasangan adalah sama.
1.
2.
1. Tekanan sumber air: 0.05 ~ 0.75 MPa.
2. Pastikan kondisi sumber air adalah bersih
(tidak ada pasir, kotoran dan lain lain)
Laju aliran tidak memuaskan 1 Lepas dan bersihkan
Air bocor disekitar bodi 2 Kencangkan
Handle longgar 3 Kencangkan
Plug tidak bisa membuka dan menutup 4 Kencangkan
Bodi goyah 5 Kencangkan
SOLUSI
MASALAH
POIN
PERIKSA