Toto GLORIA TX471SPN User manual

"PLANO" SINGLE LEVER BATH & SHOWER SET TX471SPN
30°
153 0
-7
165 0
-7
Ø68
30
20
Ø5.5
74
56°
28
150±10
G½
WALL
Cover
Packing
Body 2. CONNECTING
NUT 3. BOLT
Flow Regulator Inside
(Don t remove)
1. NOZZLES
1. Water supply pressure : 0.05 ~ 0.75 MPa.
2. Ensure that water supply is clean ( No Sand, Dirt, Etc.). 2 X Ø 5.5
Holes
1
2
Hanger
Screw
Sleeve
Anchor
Flex. Hose
w/ Packing
Hand
Shower
SPECIFICATIONS
S060158Z R8
INSTALLATION TROUBLESHOOTING
OPERATING CONDITIONS
ATTENTION
3
Handle is loose Tighten
3
CHECK
POINT
1
Unsatisfactory spray Clean
PROBLEM SOLUTION
Tighten
2
Water leaks around the handle
*Tigthen the nut by wrench.
*Tigthen the nut by hand
Nut *
Nut *
Nut *
MAINTENANCE
MOUNT CONNECTORS PARALLEL WITH THE WALL
Hot
Water
Supply Cold
Water
Supply
Leg
150
150±10
Use Seal tape
(Not Include)
All Finishes : Clean the finish with mild soap and warm water.
Wipe entire surface completely dry with clean soft cloth. Many
cleaners may contain chemicals, such as ammonia, chlorine,
toilet cleaner etc. which could adversely affect the finish and
are not recommended for cleaning
Don t use abrasive cleaners or solvents on faucets and
fittings.
Flow Regulator should not be remove because it could
damage the system
As the product model is constantly updated, the actual
product may not look the same as it shown in the
diagram, but the basic installation principles are the same.
The hot water supply side of the faucets is in a condition
of high temperature. Do not allow skin to contact with the
hardware surface directly. Otherwise,
scalding may occur.
1.
2.
3.
4.
30

"PLANO" SINGLE LEVER BATH & SHOWER SET TX471SPN
30°
153 0
-7
165 0
-7
Ø68
30
20
Ø5.5
74
56°
28
150±10
G½
WALL
Cover
Packing
Body 2. CONNECTING
NUT 3. BOLT
1. NOZZLES
2 X Ø 5.5
Holes
2
Hanger
Screw
Sleeve
Anchor
Flex. Hose
w/ Packing
Hand
Shower
SPESIFIKASI
S060158Z R8
3* Kencangkan nut menggunakan tangan
Nut *
Nut *
Nut *
30
PEMASANGAN KONEKTOR SEJAJAR DENGAN
DINDING
1. Tekanan sumber air: 0.05 ~ 0.75 MPa.
2. Pastikan kondisi sumber air adalah bersih
(tidak ada pasir, kotoran dan lain lain)
Sumber
Air Panas Sumber
Air Dingin
Leg
Flow Regulator
didalam
(Jangan dilepas)
1
PEMASANGAN PENYELESAIAN MASALAH
KONDISI OPERASIONAL
PERHATIAN
PEMELIHARAAN
Gunakan Seal
Tape (Tidak
disertakan)
* Kencangkan nut menggunakan wrench.
150
150±10
Seluruh lapisan : Bersihkan lapisan akhir dengan sabun lembut
dan air hangat. Lap seluruh permukaan hingga benar-benar
kering dengan kain lembut yang bersih. Kebanyakan bahan
pembersih mungkin mengandung bahan kimia, seperti amonia,
klorin, pembersih toilet, dll. yang dapat mempengaruhi hasil
akhir dan tidak disarankan untuk membersihkan
Jangan gunakan pembersih atau pelarut abrasif pada
faucet dan fitting.
Flow Regulator tidak boleh dilepas karena dapat merusak
sistem
Karena model produk terus mengalami pembaharuan,
aktual produk mungkin tidak sama dengan gambar, tapi
prinsip dasar pemasangan adalah sama.
Sisi pasokan air panas pada kran faucet berada dalam
kondisi suhu tinggi. Jangan biarkan kulit menyentuh
permukaan benda secara langsung. Kalau tidak, bisa
terjadi kepanasan.
1.
2.
3.
4.
Handle longgar Kencangkan
3
POIN
PERIKSA
1
Pancaran tidak memuaskan Bersihkan
MASALAH SOLUSI
Kencangkan
2
Air bocor disekitar handle