Toto EGO II TX128LELBR User manual

SPECIFICATIONS
TROUBLESHOOTING
TX128LELBR
S06726BN
CHECK
POINT
Flow rate unsatisfactory 1 Remove and clean
Water leaks around the handle 2 Tighten
Handle is loose 3 Tighten
PROBLEM
SOLUTION
2. CONNECTING
NUT
3. BOLT
1. AERATOR
550
-20
Ø95
67
G½
G½
750
-20 1139+20
0
873
183
1010+20
0
30
Floor
Ø6
R10
INSTALLATION
1
3
Sleeve
Anchor
* Cut thecover after the
mortar dry
5
2
Screw
4
* Plastic
Cover
6 X Ø6
Holes
Floor
Water Pass
Make sure flooris flat
Hot Water
Supply *
Cold Water
Supply *
Mortar
Minimum
Mortar Level
Maximum
Mortar Level
Base
COLD
Cover
a
b
HOT
EGO IILEVER HANDLE FLOOR STANDING
SINGLE LEVER LAVATORY FAUCET
6
Bolt*
Hex. Key
Base
Cover
Washer*
* Remove the Base Cover
, keep the Bolt & Washer
Bolt & Washer
(from step 6)
Hex. Key Cover
Body
Swivel
Ring
7
OPERATING CONDITIONS
MAINTENANCE
ATTENTION
1. Watersupply pressure : 0.05 ~ 0.75MPa.
2. Ensure that watersupply is clean ( NoSand, Dirt, Etc.).
All Finishes : Clean the finish with mild soapand warm water.
Wipe entire surface completely dry with clean soft cloth. Many
cleaners may contain chemicals, such as ammonia, chlorine,
toiletcleaneretc. which could adversely affect the finish and
are not recommended for cleaning.
1.Don t use abrasive cleaners orsolvents on faucets and fittings.
As the product model is constantly updated, the actual product
maynot look the same as it shown in the diagram, but the
basic installation principles are thesame.
2.
* Pipesupplied by owner

SPESIFIKASI
TX128LELBR
S06726BN
Laju aliran tidak memuaskan 1 Lepas dan bersihkan
Air bocor disekitar handle 2 Kencangkan
Handle longgar 3 Kencangkan
MASALAH
SOLUSI
POIN
PERIKSA
2. CONNECTING
NUT
3. BOLT
1. AERATOR
550
-20
Ø95
67
G½
G½
750
-20 1139+20
0
873
183
1010+20
0
30
Floor
Ø6
R10
PEMASANGAN
1
3
Sleeve
Anchor
5
2
Screw
4
* Plastic
Cover
6 X Ø6
Holes
Floor
Water Pass
Hot Water
Supply *
Cold Water
Supply *
Mortar
Minimum
Mortar Level
Maximum
Mortar Level
Base
COLD
Cover
a
b
HOT
EGO IILEVER HANDLE FLOOR STANDING
SINGLE LEVER LAVATORY FAUCET
6
Bolt*
Hex. Key
Base
Cover
Washer*
Bolt & Washer
(from step 6)
Hex. Key Cover
Body
Swivel
Ring
7
PENYELESAIAN MASALAH
* Potong cover setelah
mortar mengering
Pastikan lantainya rata
* Pipadiseidakan oleh pemilik
KONDISI OPERASIONAL
PEMELIHARRAN
PERHATIAN
1. Tekanan sumber air: 0.05 ~ 0.75 MPa.
2. Pastikan kondisi sumber air adalah bersih (tidak ada pasir,
kotoran dan lain lain)
1.Jangan gunakan pembersih atau pelarut abrasif pada faucet
dan fitting.
Karena model produk terus mengalami pembaharuan, aktual
produk mungkin tidaksamadengan gambar, tapi prinsip dasar
pemasangan adalah sama.
2.
Seluruh lapisan: Bersihkan lapisan akhir dengan sabun lembut
dan air hangat. Lap seluruh permukaan hingga benar-benarkering
dengan kain lembut yang bersih. Kebanyakanbahan pembersih
mungkin mengandung bahan kimia, seperti amonia, klorin,
pembersih toilet,dll. yang dapat mempengaruhihasil akhir dan
tidak disarankan untuk membersihkannya.
* Lepas BaseCover,
simpan Bolt & Washer