Toto MONO TX116LMN User manual

SPECIFICATIONS
S06919R
TROUBLESHOOTING
INSTALLATION
1.
2.
3.
Setting Bolt
Washer
Setting Nut
13°
230
178
Ø31.75
127
223
Ø62
40~60
max. 300
G½
253
max. 30
343
80
Ø42
Packing
Faucet
Slip Washer
Plug
Siphon
Packing
Triangle
Packing
Nut
Pipe
Nut
Use seal tape
on the Thread
( Not Include)
C
H
CHECK
POINT
Water leaks around the handle 1 Tighten
Handle is loose 2 Tighten
PROBLEM
SOLUTION
"MONO" EXTENDED LAVATORY FAUCET W/ PROGRESSIVE MIXER
& 1" ONE PUSH POP-UP WASTE (HEIGHT = 253mm) TX116LMN
R5
Base
To Hot
Water Supply To Cold
Water Supply
MAINTENANCE
OPERATING CONDITIONS
ATTENTION
1. Watersupply pressure : 0.05 ~ 0.75 MPa.
2. Ensure that watersupply is clean ( NoSand, Dirt, Etc.)
All Finishes : Clean the finish with mild soapand warm water.
Wipe entire surface completely dry with clean soft cloth. Many
cleaners may contain chemicals, such as ammonia, chlorine,
toiletcleaneretc. which could adversely affect the finish and
are not recommended for cleaning
Release the pop-up waste plug forcleaning the pop-up waste
from dirt.
1.
2.
1.Don t use abrasive cleaners or solvents on faucets and fittings.
As the product model is constantly updated, the actual product
maynot look the same as it shown in the diagram, but the basic
installation principlesare the same.
2.
13°
C
H
1. CONNECTING
NUT
2. BOLT

SPESIFIKASI
S06919R
PENYELESAIAN MASALAH
PEMASANGAN
1.
2.
3.
Setting Bolt
Washer
Setting Nut
13°
230
178
Ø31.75
127
223
Ø62
40~60
max. 300
G½
253
max. 30
343
80
Ø42
Packing
Faucet
13°
C
H
Slip Washer
Plug
Siphon
Packing
Triangle
Packing
Nut
Pipe
Nut
Use seal tape
on the Thread
( Not Include)
C
H
Air bocor disekitar handle 1 Kencangkan
Handle longgar 2 Kencangkan
MASALAH
SOLUSI
POIN
PERIKSA
1. CONNECTING
NUT
"MONO" EXTENDED LAVATORY FAUCET W/ PROGRESSIVE MIXER
& 1" ONE PUSH POP-UP WASTE (HEIGHT = 253mm) TX116LMN
R5
Base
To Hot
Water Supply To Cold
Water Supply
PEMELIHARAAN
KONDISI OPERASIONAL
PERHATIAN
1. Tekanan sumber air: 0.05 ~ 0.75 MPa.
2. Pastikan kondisi sumberair adalah bersih (tidak ada pasir,
kotoran, dll.)
Seluruh lapisan: Bersihkan lapisan akhir dengan sabun lembut
dan air hangat. Lap seluruh permukaan hingga benar-benarkering
dengan kain lembut yang bersih. Kebanyakanbahan pembersih
mungkin mengandung bahan kimia, seperti amonia, klorin,
pembersih toilet,dll. yang dapat mempengaruhi hasil akhir dan
tidak disarankan untuk membersihkannya.
Lepaskan pop-up waste plug untuk membersihkan pop-up waste
dari kotoran.
1.
2.
1.Jangan gunakan pembersih atau pelarut abrasif pada faucet dan fitting.
Karena model produkterus mengalami pembaharuan, aktual produk
mungkin tidak sama dengan gambar,tapi prinsip dasar pemasangan
adalah sama.
2.
2. BOLT