Toto TLE0150 Series User manual

-1-
0000653 2022.04
Touchless Faucet
For the complete function of this product, please install it correctly according to the
instructions in this installation manual.
After installation, please explain the use to the customer, and that the product
includes an owners manual (warranty within).
Installation Manual

-2-
WARNINGS
People with disabilities, mental disabilities, or lack of common
sense (including children) should use this product under
supervision of assigned personnel.
Do not use loose power sockets.
Failure to do so may result in a fire or electric shock.
Never splash water on the power plug or the controller.
The auto faucet is an electrical appliance, this may cause
product malfunction.
Do not use a power source other than the specified power
source (AC 220 V-240 V).
Failure to do so may result in a fire or electric shock.
Do not exceed the rated power of the socket or patch panel.
Failure to do so may result in a fire.
Do not bend the power cord, place heavy objects on the cord,
nor handle improperly.
Failure to do so may result in a fire.
Do not process the power cord (cut or connect power cord).
Failure to do so may result in accidents like a fire or product
malfunction.
Do not plug or unplug the power plug with wet hands.
Failure to do so may result in electric shock.
Do not contact the wire plug during thunderstorms.
Failure to do so may result in electric shock.
Do not place the auto faucet in a high humidity area such as
a bathroom.
This may cause damage.
Ignoring the content in this column and improper use
could result in personal death or serious injury.
Please entrust the installation of this product to qualified
professionals.
WARNINGS
CAUTION
Never disassemble, reassemble, repair or modify the
Automatic Faucet, unless you are an electrician, or qualified
service person.
This may cause property damage or personal injury.
Please be sure to consider the installation location of the
power socket or waterproof socket to avoid water exposure
from condensation on the water inlet pipe or splashing of
water droplets during use.
Always close the stop valves before removing the filter.
Failure to do so may result in scald injuries and defacement
of family property due to the jet of hot and cold water.
The socket installation position should comply with relevant
design codes.
Hold the power plug and pull it out when unplugging the
power supply.
It may damage the outlet and power cord, then causes fire or
electric shock when unplugging the power supply.
Please be sure to insert the plug completely.
Failure to do so may result in a fire or electric shock.
For AC type, if dust accumulates on the power plug, moisture
may compromise the insulation and cause a fire.
Please unplug the power plug and wipe with a dry cloth (once
a month). After wiping, use silicone for waterproofing.
Do not force or strike.
Failure to do so may result in product malfunction or a leak.
Do not use on vehicles, boats, or other mobile objects.
Ignoring the information in this column and improper use
could result in personal injury or property damage.

-3-
1. SET-UP DRAWING
CAUTION
Do not install it outdoors or in places where it may freeze.
Failure to do so may result in damage to the components,
which may cause damage to the property as a result of
leakage and soaking.
Remove dust from the plug blades regularly (once a month)
and be sure to insert the plug completely.
Do not make modifications, such as installing parts other than
structural parts of this product or removing parts.
Failure to do so may result in electric shock or product
malfunction. In addition, it may damage the performance of
the product, resulting in scalds injuries, and property damage
due to leakage and soaking.
No person other than a service engineer should disassemble,
repair, or modify this product, unless it is specifically
described in this manual.
Failure to do so may result in product malfunction or electric
shock.
Please be sure to periodically (twice a year at least) check
the piping and its surroundings (inside the cabinet rack,
inside the inspection port, etc.) for leaks or looseness.
Do not block the Spout when using it. Otherwise, water will
seep from the spout body and cause leakage, which may
result in incidents that damage furniture and property.
Please repair the parts in time when they are loose.
Do not force or strike the electroplated coatings.
Please use neutral detergent only.
Remove power plug when not use it for a long period of time.
Remove the backup batteries connectors for self-generating type.
It may cause unexpected accidents by mis-operation of
malfunctions.
When there is an emergency, such as leakage, burst pipes,
or displacement of the product, close the stop valves in steps.
If the water is still not turned off, close the master valve.
100
Minimum
150–300
400
150
Minimum
100
150
150–300
400
100
Counter type
Wall mount type
Power plug
(for AC type)
Power plug
(for AC type)
(mm)
(mm)
Connect to the hose
(Not included
in this product)
Connect to the
stop valve
(Not included
in this product)
Connect to the hose
(Not included
in this product)
Connect to the
stop valve
(Not included
in this product)
100
Minimum
150
Minimum

-4-
3. INSTALLATION PROCEDURE2. STRUCTURAL PARTS
3
sensor sensor
TLE01501*
TLE01502*
TLE03501*
TLE03502*
TLE04501*
TLE04502*
ECOPOWER type only
Backup
battery
1
Before Installation
2
Spout
Controller
Counter type Wall type
The shape of the actual product may differ somewhat from drawings
depending on the model number.
After supplly electricity, sensor will set up automaticlly
(about 20 seconds)
1. This is non-rechargeable battery is not to be recharged.
2. Must replaced with battery from TOTO.
3. Battery is to be inserted with correct polarity.
4. Exhausted battery is to be removed from the appliance
and safety disposed of.
5. if the appliance is to be stored unused for a long period,
the battery should be removed.
6. The supply terminals are not to be short -circuited.

-5-
3. INSTALLATION PROCEDURE
80
Φ5
Φ47
190 450
80
90°
WL
2-Φ5
23
Unit: mm
For under the counter: Top of the counter
For the countertop: Top of the basin
Unit: mm
1
Install the Controller
1 2
Install the Spout for Counter type
2
1
Install the Spout for Wall mount type
32 4 5
3
D-cut
D-cut
7
(TLE23004*, TLE23005*, TLE24004*, TLE24010*,
TLE24005*, TLE25004*, TLE25005*, TLE25010*)
(TLE26004*, TLE26005*,TLE26010*)
6

-6-
3. INSTALLATION PROCEDURE
DC type
AC type
1 2
3 4 5
Connect the Spout to the Controller
The shape of the actual
product may differ somewhat
from drawings depending on
the model number
Please check battery pole in right
way when you put in battery case.
If sensor not working, please change
new battery AA type 2 units.
1. These are non-rechargeable batteries are not to be
recharged.
2. Different types of batteries or new and used
batteries are not to be mixed.
3. Exhausted batteries are to be removed from the
appliance and safely disposed of.
4. If the appliance is to be stored unused for a long
period, the batteries should be removed.
5. The supply terminals are not to be short-circuited.
After supply electricity, sensor will set up
automatically (about 20 seconds)
Battery
(1.5V x2UT)
Cover
Caution
Put Battery (TLE0450**)

-7-
4. OPERATION
3. INSTALLATION PROCEDURE
1 2
Before installing the product, be sure to thoroughly flush the
supply pipes of dirt and debris.
Remove the controller cover, connect backup battery to
controller. Product will require 3 min to initialize.
* ECOPOWER type only
Before Installation
1
2
Mount the bracket on the wall.
Insert the controller part into the fixing plate and tighten the fixing
nut. (Alignment of D-cut part)
Connect the water supply line to the controller inlet.
Install the Controller
1
2
3
Secure the Spout to the countertop with the included mounting
hardware.
Cut the spout connecting hose if necessary. Connect the spout
connecting hose to the controller.
Install the Spout for Deck-Mounted Models
1
2
Draw the center line of the installation position on a rough wall
as shown in the figure below.
Excavate a rough wall according to the size drawn (excavation
depth is 80 mm)
Place the connected PVC pipe in the center of the groove (fix it
with a wooden block if necessary)
Secure the wall PVC pipe with cement to decorate the wall
(tiles, etc.)* PVC pipe is cut to the same height as the wall
(After the cement is completely dry) Center the center of the
PVC pipe and hit it against the wall as shown.
4 holes.
Install the Spout for Wall-Mounted Models
1
2
3
4
5
(TLE23004*, TLE23005*, TLE24004*, TLE24010*, TLE24005*, TLE25004*, TLE25005*, TLE25010*)
Insert the expansion tube and screw in the screw to secure the spout
base. Insert the faucet and tighten the faucet. Bottom fixing screw
(TLE26004*, TLE26005*,TLE26010*)
Push the expansion tube into the hole. Fix the faucet with screws, attach the
flange to the faucet, The wiring for the water hose and photoelectric sensor is
inserted into the PVC pipe of the pre-filled water nozzle. Tighten the flange.
Guide the water inlet hose and photoelectric sensor wiring from
the bottom port of the PVC pipe and attach the flange.
6
7
Connect the hose. Secure the hose with a clip.
Place the battery in the battery box. Connect the battery box
and controller.*DC type only
Insert the sensor connector till it stops with a click.After inserting the
connector, insert the sensor cord into the groove of the controller as shown.
Attach the controller cover by the screw.
Connect Power plug. *AC type only
After supply electricity, sensor will set up automatically (about 20 seconds).
Connect the Spout to the Controller
1
2
3
4
5
1. Place the hands close to the spout.
When the sensor detects the hands, water will discharge automatically.
2. Move the hands away.
After moving the hands away for 1-2 seconds, the water will stop.
Water valve will automatically stops discharging water after
continuously discharging for approximately 1 minute.
(If another discharge is wanted, please move the hands away
and allow the detector to re-sense the hands.)

-8-
1 8 2
7
6
34 5
Close
Open
SPECIFICATIONS
5. CLEANING THE FILTER SCREEN AND CONSTANT FLOW VALVE
1. Close the stop valve.
2. Remove functional part cover and use the open-close tool to
take out filter and flow regulator.
3. Remove the flow regulator from the filter.
4. Shake the filter in water to wash away the debris accumulated within.
5. Wash the flow regulator.
6. Connect the flow regulator to the filter.
7. Use an open-close tool to reinstall the filter and flow regulator.
Reinstall the functional part cover.
8. Open the stop valve.
TLE0150** TLE0350** TLE0450**
AC type
ECOPOWER type DC type
AC 220 V-240 V
50/60 Hz
ECOPOWER
Backup Li-battery
Dry battery
AA x 2
TLE04501*:
0.1 MPa (flowing)
TLE04502*:
0.05 MPa (flowing)
TLE03501*:
0.1 MPa (flowing)
TLE03502*:
0.05 MPa (flowing)
TLE01501*:
0.1 MPa (flowing)
TLE01502*:
0.05 MPa (flowing)
0.75 Mpa (Resting)
130-200 mm (Sensor is self-adusting)
TLE01501*, TLE03501*, TLE04501*: 1.3 L/min
TLE01502*, TLE03502*, TLE04502*: 2.0 L/min
G 1/2
1-40 °C
Model
Type
Power source
voltage
Power
consumption
Minimum
water
pressure
Operating
Standby
1 W
1 W
-
-
-
-
Maximum
water
pressure
Water
supply
pressure
Sensing distance
Operating ambient
temperature
Flow rate
Thread specifications
of water supply
connection
Pay attention to the orientation
of the flow regulator
Do not remove the
flow regulator