TouchTronics POWERTouch P1555 Series User manual

NST13308-P1555_A 2020-06-10 Page 1
57315 Nagy Dr
Elkhart, IN 46517
800-294-2570
574-294-2570
www.touchtronics.com
www.touchtronics.com
Product is
3” x 5” x 1”
POWERTouch P1555 Series
Radio Frequency (RF) Remote Control System
SERVICE MANUAL
P1555
P1000-TX2
P1000-TX2S
P1000-TF2
P1000-TX4S P1000-TX6S With ON/OFF Switch
P1000-TK1 P1000-TK2 P1000-TK4
P1000-TF2-LK P1000-TF4 P1000-TF6
P1000-TM1 P1000-TM2 P1000-TM4
Receiver can be paired to any transmitter below
TK Sealed Transmitters
TF Sealed Transmitters
TM Transmitters
TX Transmitters
P1000-TF2
P1000-TX2S
TM
Sealed
RANGE 300 Feet Typical
Up to 600 Feet
OUTPUT 4 Relays, Positive, 5A
OPTIONAL 2 (+12v) A1 & A2
FREQUENCY 433 MHz
CODES Rolling Codes
Secure Encryption
VOLTAGE +12VDC or +24VDC
CURRENT
OUTPUT
• 30 Amps, K1 & K2
• 15 Amps, K3 & K4
INPUT
• 10mAmps
ANTENNA
OPTIONAL
Fixed - Standard (shown)
TNC Whip
Flex Whip / Roof Mount
Flex Whip / Glass Mount
HARNESS 9" Standard, 10 pin connector, 18AWG
BATTERY
All transmitter styles (except TX style)*
• Coin Style, Lithium, CR2032
• 100,000 1-second pulses
• 10 year shelf life
*TX Style - 9V
SYSTEM SPECIFICATIONS
Model # P1555 Series
(see page 2 for model number chart)

X
NST13308-P1555_A 2020-06-10 Page 2
X
Receiver Installation
Determine mounting location of receiver and
antenna - typically under the dash or behind a
wall.
Antenna Installation
1. The antenna must be installed in an open, non-
metal area in order to receive RF (radio
frequency) transmissions.
2. Antenna range will be reduced if located:
A) within 6 feet of a large motor
B) near large bundles of wires
C) near other RF devices
D) touching any metal
To Increase Antenna Range
A) Install exterior mount NMO Antenna
See page 4 for accessory antenna options
Each time a button is pressed on the transmitter, the corresponding output will turn On. For example, if button #1
is pressed, output #1 will turn On as long as the button is held.
If an input signal is sent to inputs A1 or A2, the corresponding output will turn On as long as the signal is present.
(A1 = Output #1 is ON. A2 = Output #2 is ON)
Each output is factory set as momentary.
SYSTEM OPERATION
CODE ENROLLMENT
INSTALLATION
1555-R12
Receiver
Model
4 - Relays 12VDC Fixed
Antenna
TNC Antenna
A1 &
A2
Switch Inputs
RECEIVER MODEL NUMBER CHART
ENROLLING NEW TRANSMITTERS - Self-Learning Receiver
1. Remove and reconnect power to unit. This will automatically place unit into LEARN mode for 5-seconds.
2. Press buttons 1 & 2 on transmitter, within the 5-second LEARN time. Wait 5-seconds and confirm the
transmitter has been enrolled by pressing any button and verifying an output action is performed.
2*. Exception: Enrolling a P1000-TX4S transmitter-
Press buttons 1 & 4 on transimitter, within the 5-second LEARN time. (Not buttons 1 & 2)
OR
1. Remove cover from receiver enclosure.
2. Locate LEARN switch (small, push-button style switch located in the corner of the printed circuit board)
3. Press and release the LEARN switch
The Red LEARN LED next to the switch will flash
4. Press buttons 1 & 2 on transmitter, while Red LED flashes. (Buttons 1 & 4 if enrolling P1000-TX4S)
5. Red LEARN LED double blinks to confirm enrollment.
6. Press any button on the new transmitter to confirm that the new transmitter code has been enrolled.
7. Replace receiver enclosure cover.
Erasing Enrolled Codes
1. Press and hold the LEARN switch (see #2 above) for 10-seconds.
2. Red status LED will flash while holding LEARN switch
3. Release LEARN switch when Red LED double flashes to confirm ALL transmitter codes are erased.
Sealed
Potted
24VDC
1555-R24
XX XXX X
XXXXXX
OPT
OPT

NST13308-P1555_A 2020-06-10 Page 3
X
roDEXIF(ANNETNA TNC)
2-1J,2AtupnIhctiwS
1-1J,1AtupnIhctiwS
4-1J,rewoPcigoL
3-1J,dnuorG
LOGIC
1
2
3
4
5
6
7
8
9
01
1
2
3
4
5
6
7
8
9
01
DER/THW
DER/YRG
KLB
DER
KNP
YEL
GRO
ULB
NRG
KNP
DNUORGSISSAHC
TUPNIREWOP
TUPTU )O +(PMA5,1
5,2TUPTU )O +(PMA
)+(PMA5,3TUPTUO
TUPTUO 5,4 )+(PMA
DRADNATS
4-1SYALER
J1
TUPN ,I 1 2AA
)Am01(slangiScigoL
AB YRETT
RAB ET YT
1 Amp
5 Amp
See Note Below
Call Factory for Custom Applications
Touchtronics, Inc. 1-800-294-2570
P1550 RELAY USER SELECTED OUTPUTS
POWER FUSED AT 5 AMPS
Output 1
J1-6
Output 2
J1-7
Output 3
J1-8
Output 4
J1-9
roDEXIF(ANNETNA TNC)
2-1J,2AtupnIhctiwS
1-1J,1AtupnIhctiwS
4-1J,rewoPcigoL
3-1J,dnuorG
LOGIC
1
2
3
4
5
6
7
8
9
01
1
2
3
4
5
6
7
8
9
01
DER/THW
DER/YRG
KLB
DER
KNP
YEL
GRO
ULB
NRG
KNP
DNUORGSISSAHC
TUPNIREWOP
TUPTU )O +(PMA5,1
5,2TUPTU )O +(PMA
)+(PMA5,3TUPTUO
TUPTUO 5,4 )+(PMA
TUPNIREWOP
DRADNATS
4-1SYALER
J1
TUPN ,I 1 2AA
)Am01(slangiScigoL
AB YRETT
RAB ET YT
1 Amp
10 Amp
See Note Below
Call Factory for Custom Applications
Touchtronics, Inc. 1-800-294-2570
P1550 RELAY USER SELECTED OUTPUTS
POWER FUSED AT 10AMPS
Scrape paint and clean area before installing ground screw
A loose chassis ground connection WILL cause intermittent operation!
#10 x 3/4” Screw
#10 3/16” Star Washer
#10 3/16” Ring Terminal
Vehicle Frame
CHASSIS GROUND
Output 1
J1-6
Output 2
J1-7
Output 3
J1-8
Output 4
J1-9
*USER SELECTABLE
*USER SELECTABLE
NOT USED
+12V or 24V / A1
+12V or 24V / A2
+12V or 24V / Logic
+12V or 24V / A1
+12V or 24V / A2
+12V or 24V / Logic

X
NST13308-P1555_A 2020-06-10 Page 4
X
Limited One (1) Year Warranty
1) Each individual product is warranted under the TouchTronics Limited Warranty program for 1 full year from date of purchase or a maximum
of 2 years from the date of manufacture.
2) No product will be covered under the TouchTronics Limited Warranty program that has a manufacture date older than 2 years.
3) To receive technical support or warranty service, call our technical support center during regular business hours. 1-800-294-2570
4) To enable our technical support staf f to better serve you, please have the following information available when you call.
Purchase
Installation
Date Of:
Dealer Name
Dealer Phone
Make / Model
Vehicle Information:
Model Number
Serial Number
Product Information:
Fill in all pertinent information at the time of purchase or installation.
TouchTronics, Inc. Warranty Policies and Procedures
TouchTronics, Inc. All Rights Reserved. TouchTronics, the TouchTronics logo, and other TouchTronics marks are owned by TouchTronics and may be registered. TouchTronics assumes no
responsibility for any errors that may appear in this manual. Information contained herein is subject to change without notice.
FCC Compliance and Advisory Statement. This hardware device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful
interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed or used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1) reorient or relocate the receiving antenna; 2) increase the separation
between the equipment and the receiver 3) connect the equipment to an outlet on a circuit different from that to which the receiver is connected; 4) consult the dealer or an experienced radio/TV
technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Where shielded interface
cables have been provided with the product or specified additional components or accessories elsewhere defined to be used with the installation of the product, they must be used in order to ensure
compliance with FCC regulations.
Canadian DOC Statement. This digital device does not exceed the Class B limits for radio noise emissions from digital apparatus specified in the interference-causing equipment standard entitled
Apparatus,” ICES-003 of the Department of Communications.
This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1) this device may not cause interference, and 2) this device must accept any
interference, including interference that may cause undesired operation of the device.
TouchTronics, Inc. Tous droits réservés. TouchTronics, le logo TouchTronics et les autres marques TouchTronics sont la propriété exclusive de TouchTronics et sont susceptibles d'être des
marques déposées. Toutes les autres marques sont la propriété exclusive de leurs détenteurs respectifs. TouchTronics décline toute responsabilité en cas d'erreurs dans ce manuel. Les
informations énoncées dans le présent document peuvent faire l'objet de modifications sans avis préalable.
Déclaration FCC. Cet équipement a été testé et déclaré conforme à la section 15 du règlement de la FCC. Son fonctionnement est soumis aux conditions suivantes: 1) l'équipement concerné ne
doit pas causer d'interférences dangereuses, et 2) il doit accepter toute interférence reçue, y compris les interférences risquant d'engendrer un fonctionnement indésirable. Cet équipement a été
testé et déclaré conforme aux limitations prévues dans le cadre de la catégorie B des appareils numériques défini par la section 15 du règlement de la FCC. Ces limitations sont stipulées aux fins de
garantir une protection raisonnable contre les interférences gênantes en installation résidentielle. Cet équipement génère, utilise et diffuse des ondes radio, et s'il n'est pas installé ni utilisé en
conformité avec les instructions dont il fait l'objet, peut causer des interférences gênantes avec les communications radio. Cependant, nous ne pouvons vous garantir qu'une interférence ne se
produira pas dans une installation particulière. Si cet équipement produit des interférences graves lors de réceptions radio ou télévisées qui peuvent être détectées en allumant et en éteignant
echnical Support Via Web Site / Email
w.touchtronics.com
[email protected] or
‘Contact Request’ link on the web page
Technical Support
Phone [phone]
Fax [phone]
Numbers Sales Support
Phone [phone]
Fax [phone]
Email [email protected]
One
Seller will warrant any product originally manufactured or assembled and sold by seller for a period of upto TWO YEARS (24 months) from the original date of manufacture or ONEYEAR (12 months) from
original retail sale or O.E.M. in-service date.
Two
following are in lieu of all warranties; expressed; implied; or statutory, including but not limited to, any implied warranty of merchantability of fitness for a particular purpose and of any other warranty
obligation on the part of seller. Seller, except as otherwise hereinafter provided, warrants the goods against faulty workmanship or defective materials for a period ofup to TWOYEARS (24 months) from the
date of manufacture or ONEYEAR (12 months) from the original retail or O.E.M. in-service date.
Seller’s sole and exclusive liability shall be (at seller’s option) to repair; replace; or credit buyer for such goods which are returned by buyer during the applicable warranty period set forth above, provided
seller is promptly notified in writing or by phone upon discovery by buyer that such goods failed to conform and an explanation of any alleged deficiencies, (II) such goods are returned to seller, (III)
examination of such goods shall disclose that such alleged deficiencies actually exist and were not caused by accident, misuse, neglect, alteration, improper installation, unauthorized repair or
improper testing. If seller elects to repair or replace such goods, seller shall have a reasonable time to make such repairs or replace such goods.
r’s warranties as herein above set forth shall not be enlarged, diminished, or affected by, and no obligation or liability shall arise or grow out of, sellers rendering of technical advice or service.
Damage to products caused by the customer or during installation cannot be claimed under this warranty. All devices returned that are not covered under the seller’s warranty policy, will be charged a
minimum of $25.00 for evaluation plus additional charges for components and labor to repair the device not to exceed the original selling price. Seller considers the following to be typical examples of
customer or installation damage: burned or broken traces on the printed circuit board, burned or damaged components, dirt or water residue on the printed circuit board or inside the case, modifications by
customer, broken cases or housings and dead batteries
Three
return material authorization number (RMA) must be issued by seller before any product is returned for evaluation or repair. Warranty repairs must be completed at authorized repair facilities.
ANT11405-1
ANT10430-2
ANT11514-1
ANT11514-2
Accessories Minimum Orders: $25.00
TNC, Wire Whip Antenna (see pg 1)
Glass Mount Antenna Kit, 14 foot cable
Flex Whip Antenna Kit, 5 foot cable, roof mount
Flex Whip Antenna Kit, 14 foot cable, roof mount
Call Factory for Current Pricing and Availability
Note: Not available on
Standard, Sealed,
P1555-R Models