TouchWand ACWand User manual

Page 1of 8
TouchWand™
ACWand
2019 –Version: 03

Page 2of 8
Table of Contents
General..........................................................................................................................................................3
Safety Precautions ........................................................................................................................................3
ACWand Installation .....................................................................................................................................4
How to add ACWand units to Wanderfull controller....................................................................................6
Specifications & Part Numbers .....................................................................................................................7
List of Air conditions supported by ACWand................................................................................................8

Page 3of 8
General
The ACWand is a smart device that controls air conditioning units and monitors and saves
energy. This Wi-Fi enabled transceiver is fully compatible with any Wi-Fi network. It is
compatible with most of the known air conditioners in the market.
You can use the ACWand to control your AC through the TouchWand app to turn it on/off,
change between cool/heat modes, fan modes and control the temperature.
Safety Precautions
•Choose a Suitable Location
•Do not locate the device facing direct sunlight, or in a humid or dusty place.
•Suitable ambient temperature for the module is 0°C-40°C.
•Do not locate the module near any combustible substances or source of heat, e.g. fires,
radiators, boiler, etc.

Page 4of 8
ACWand Installation
1. Press and hold SW1, then connect the power adaptor to the device (while pressing).
2. Hold SW1 until a green LED turns on. It will enter Access Point mode. The Access Point
setting are:
a. SSID: "RolbitSetAP"
b. Password: "rolbit1234"
3. After the connection to AP has been made, open web browser and go to IP: 192.168.4.1
4. Press and hold SW1 and refresh the page at the same time. You will be redirected to the
following setup page:

Page 5of 8
5. Fill your Home SSID and Password. Server IP should be the IP
1
of the Controller. Server
Port should be 7433.
NOTE: You can only connect the ACWand to a 2.4GHZ Wi-Fi network.
The name of the network should be without spaces.
6. Press and hold SW1 and click Send.
Note: Be sure to Press and Hold SW1 then click the Send key.
7. Disconnect the Power adaptor from the unit.
8. Wait 10 seconds and plug back the power adaptor.
Note: If there are more units to be configured to the same network, repeat the following
steps for a faster configuration:
After configuring the first unit in step 6, keep the browser open at 192.168.4.1/submit
1. Repeat steps 1, 2.
2. Press and hold SW1 and refresh the browser page at 192.168.4.1/submit
3. Repeat step 7.
1
To find your own Controller IP, go to http://www.touchwand.com/products/touchwand-wanderfull-hub/
Click "Installation manual" button. Inside the manual, go to page 6.

Page 6of 8
How to add ACWand units to Wanderfull controller
The ACWand uses Wi-Fi connection to connect and pair with the Wanderfull controller. To
pair the unit with the system, follow these steps:
1. When logged in with a TECH user to the TouchWand app, go to Settings → ACWand.
2. Check 'Enable connection'.
3. Fill the following details:
oListen on IP: 0.0.0.0
oPort: 7433
oMax connections should be the number of units to be installed.
4. Press 'Save' button.
5. Go to Units page →press Add Unit.
6. Select 'ACWAND'.
7. Enter MAC address (run IP scanning tool in your computer).
8. Select Temperature sensor.
9. Select AC type.
10. Enter AC name.
11. Press 'Pair' button and 'Done'.

Page 7of 8
Specifications & Part Numbers
Temperature
measurements range
10°C to 30°C
Power supply
48g
Operating temperature
5°C to 40°C
Accuracy
3% + 0.5°C
Enclosure rating
IP20 for indoor
Certification
CE
Wireless range
100 Ft
Frequency
2.4GHZ
Wi-Fi security
Connection to the network is open. Data in the controller and the cloud
is secured.
Wi-Fi security
programming
Configuration via Wi-Fi
Network settings
Landing page
Indication
Activity indicate using LED lights
Warranty
2 years

Page 8of 8
List of Air conditions supported by ACWand
A/C
manufacturer
MODEL
Electra
Tadiran /
Amcor
Tornado
Family line
AUX
YKR-F015E
YKR-K/002E
V
V
V
MIDEA
RG06C BGEF
R51K BGE
RG36F BGEF
V
V
HISENSE
DG11J104
DG11J101
V
TADIRAN
HISENSE
RCH28NE
V
CHIGO
ZHEZ-01
ZHTT-04
V
TADIRAN
TAC 290
V
GREE
YB1FA
YACIFBI
YT1F
YX1F
V
ELECTRA
RC3
RC4
RC7
V
Specifications are subject to change and improvement without notice.
The manufacturer TouchWand Ltd. declares under our sole responsibility that the product:
Marketing model: TouchWand ACWand
Trade/Brand name: ACWand™
Changes or modifications not expressly approved by TouchWand Ltd. for compliance could void the
user’s authority to operate the equipment.