Town & Country Fireplaces T120.RHKIT User manual

120913-8 T120.RHKIT 5055.T120
T120.RHKIT
INSTALLATION
AND OPERATING INSTRUCTIONS
OPTIONAL
REMOTE HEAT KIT
IMPORTANT:
THESE INSTRUCTIONS ARE TO REMAIN WITH THE
HOMEOWNER
FOR WOOD FIREPLACES
HEAT OUTLET
DUCT
REMOTE
BLOWER
ASSEMBLY

2 T120.RHKIT 120913-28
Replacement Parts
1...... DUCT ADAPTER PLATE................... FP30.9128
2...... OUTLET GRILL.....................................5096.854
3...... REMOTE HEAT FLAP BOX................T120.7940
4...... TRANSITION BOOT.............................5096.853
5...... BLOWER CASING FACE PLATE................9144
6...... BLOWER FAN BRACKET...........................9146
7...... BLOWER WALL BRACKET........................9147
8...... REMOTE BLOWER BOX ..................TC36.9141
9...... BLOWER.................................................5024.65
12
3
4
5
6
789
11
12
13
7
10 ..... WIRE PIG TAIL .............................. TC36.50625
11 ..... INLET GRILL.......................................5096.851
12 ..... JUNCTION BOX .................................5024.408
13 ..... RHEOSTAT KIT ..................................5025.001
........ REMOTE BLOWER ASSEMBLY
............. (Items 5 to 10) ..............................TC36.9141
10
ITEM DESCRIPTION PART NUMBER ITEM DESCRIPTION PART NUMBER

T120.RHKIT 120913-28 3
INSTALLATION EXAMPLES
Theamountof heat from
this kit is affected by
the length and number
of bends. To maximize
the performance the
length and number of
bends should be kept to
a minimum.
ROUND DUCT
(6” TYPE ”B”)
MAXIMUM
DUCT LENGTH OF 20 FT.
RECTANGULAR DUCT
(10” X 3 1/4”)
MAXIMUM
DUCT LENGTH OF 20 FT.
CHIMNEY INSTALLTIONS
NOT SHOWN

4 T120.RHKIT 120913-28
WALL OR CEILING INSTALLATION
The Optional Remote Heat Kit allows heat to
be transferred to other parts of the home. One
to four Remote Heat Kits may be used.
1) Remove the knockout panel from the top of
the unit for each Remote Heat Kit you are
installing.
REMOVE THESE KNOCKOUT
PANELS AS NEEDED
2) Remove the insulation directly below the
opening down to the heat shield.
4) Attach the Duct Adapter Plate to top of unit
using 4 screws.
3) Install the Flapper Box to the top of the unit.
Ensure that the ap in the assembly is free to
move. (Flap should be in the normally closed
position with the blower off)
INSULATION
(REMOVED)
Fig. #2
Fig. #4
Fig. #1
Fig. #3
FLAPPER BOX
INSTALLED

T120.RHKIT 120913-28 5
5) Locate the Remote Blower Assembly in the
desired wall or ceiling location, maximum
20 ft. away from the unit, and secure to the
framing.
6) Attach the 3 1/4” x 10” Transition Boot to
the Remote Blower Assembly and seal with
aluminium duct tape. Run a 6” diameter
approved Type “B” venting between the
blower and the replace. Fasten in place with
screws and seal with aluminium foil tape.
7) Locate the make-up air inlet in a desired
location in the chase wall.
8)Attach nishing grills over both inlet and outlet
using the screws provided.
Fig. #5 BLOWER ASSEMBLY
HEAT DUCT
TRANSITION BOOT

6 T120.RHKIT 120913-28
ELECTRICAL WIRING
NOTE: ALL ELECTRICAL WIRING MUST BE
DONE BY A QUALIFIED ELECTRICIAN.
Consult local codes or, in the absence of
local codes, with the current CSAC22.1 Ca-
nadian Electrical Code and in the USA with
the National Electrical Code, ANSI/NFPA 70
(Latest Edition).
SPEED
CONTROL
BLOWER
120 VOLTS
60 Hz
0.7 AMPERES
G (green)
L1 (white)
L2 (black)
Fig. #10
The Optional Remote Heat blower electrical
rating: 120V, 60HZ, 80 watts. For your protec-
tion against shock hazard, use only a properly
grounded power supply.
This kit includes a junction box, rheostat
and cover plate. The junction box should be
mounted in a convenient location away from
the fireplace.

T120.RHKIT 120913-28 7
OPERATING INSTRUCTIONS
The wall mounted rheostat is used to turn the
blower ON and OFF, as well as to control its
speed.Pleasenotethat the blower will operate
independently to the fireplace. With the blower
on heat will be distributed when the fireplace
is on and room air will be circulated when the
fireplace is off.
To turn the blower on, rotate the control knob
clockwise until the switch clicks on. Continue
to rotate the knob clockwise to reduce the
blower speed. To turn the blower OFF, rotate
the control knob counter-clockwise until the
switch clicks off.
Fig. #11
MAINTENANCE
Town & Country recommends that this kit
is cleaned at least once a year. It may be
necessarytoincreasethefrequencyofcleaning
depending on the room location, type of floor
coverings, amount of renovation work, etc.
To clean, remove the grill then use a vacuum
to clean around the blower and grill, ensuring
not to damage the fan blades.
CONTROL
KNOB

8 T120.RHKIT 120913-28
TECHNICAL SUPPORT: 1-250-748-1184
Web site: www.townandcountryfireplaces.net
2974 Allenby Road, Duncan, BC Canada V9L 6V8