Town & Country Fireplaces TC36.RHKA User manual

240506-8 TC36.RHKA 5056.4277
INSTALLATION AND
OPERATING INSTRUCTIONS
OPTIONAL
REMOTE KIT
TC36.RHKA
MAKE-UP AIR INLET DUCT
HEAT OUTLET DUCT
REMOTE BLOWER
ASSEMBLY
IMPORTANT:
THESE INSTRUCTIONS ARE TO REMAIN
WITH THE HOMEOWNER

2
070606-8 TC36.RHKA 5056.4277
Replacement Parts
1...... DUCT ADAPTER PLATE ................... TC36.9128
2...... OUTLET GRILL ....................................5096.854
3...... REMOTE HEAT FLAP BOX............... TC36.9122
4...... TRANSITION BOOT ............................. 5096.853
5...... BLOWER CASING FACE PLATE ................ 9144
6...... BLOWER FAN BRACKET............................ 9146
7...... BLOWER WALL BRACKET......................... 9147
8...... REMOTE BLOWER BOX ................... TC36.9141
9...... BLOWER ................................................. 5024.65
12
3
4
5
6
7
89
12 11
13
14
7
10 ..... WIRE PIG TAIL ............................... TC36.50625
11 ..... INLET GRILL.......................................5096.851
12 ..... INLET ADAPTER BOOT ..................... 5096.852
13 ..... JUNCTION BOX..................................5024.408
14 ..... RHEOSTAT KIT ................................... 5025.001
........ REMOTE BLOWER ASSEMBLY
............. (Items 5 to 10)............................... TC36.9141
10
ITEM DESCRIPTION PART NUMBER ITEM DESCRIPTION PART NUMBER
15 5/16”
7 5/16”
7 3/8”
7 3/8”

3
070606-8 TC36.RHKA 5056.4277
INSTALLATION EXAMPLES
The amount of heat from
this kit is affected by
the length and number
of bends. To maximize
the performance the
length and number of
bends should be kept to
a minimum.
Duct clearance to combustible material:
- within 36” of unit = 1/2”
- more than 36” from unit = 0”
ROUND DUCT (6”)
MAXIMUM
DUCT LENGTH OF 25 FT.
RECTANGULAR DUCT
(10” X 3 1/4”)
MAXIMUM
DUCT LENGTH OF 25 FT.

4
070606-8 TC36.RHKA 5056.4277
WALL OR CEILING INSTALLATION
The Optional Remote Heat Kit allows heat to
be transferred to other parts of the home. One
or two Remote Heat Kits may be used.
1) Remove either of the knockout panels from
the top of the unit.
REMOVE EITHER OF THESE
KNOCKOUT PANELS
2) Remove the insulation directly below the
opening and remove the lower cover plate.
4) Attach the Duct Adapter Plate to top of unit
using the 4 screws previously removed.
3) Install the Remote Heat Flap Box to the top
of the unit and x using two screws. Ensure
the opening in the heat box mates with the
opening in the channel on the unit, and that
the ap in the assembly is free to move. (Flap
should be in the normally closed position
with the blower off)
LOWER COVER PLATE
(REMOVED)
INSULATION
(REMOVED)
Fig. #2
OPENING IN THE CHANNEL
Fig. #3
OPENING IN THE HEAT BOX
Fig. #4
Fig. #5
Fig. #1

5
070606-8 TC36.RHKA 5056.4277
5) Locate the Remote Blower Assembly in the
desired wall or ceiling location, maximum
25 ft. away from the unit, and secure to the
framing.
7) Remove the make-up air knockout panel
from the left hand side of the unit. (If two
remote heat kits are to be used only one
make up air kit is required)
8) Attach the Duct Adapter Plate over the
side opening with the 4 screws previously
removed.
6) Attach the 3 1/4” x 10” Transition Boot to
the Remote Blower Assembly and seal with
aluminium duct tape. Run a 6” diameter
exible aluminium heat duct or equivalent
between the blower and the replace. Fasten
in place with screws and seal with aluminium
foil tape.
Fig. #6
Fig. #8
BLOWER ASSEMBLY
HEAT DUCTTRANSITION BOOT
DUCT
ADAPTER
PLATE
9) Locate the make-up air Inlet Adapter Boot in
a desired location and secure to framing.
10)Run a 6” diameter duct from the adapter to
the replace. Fasten in place with screws
and seal with aluminium foil tape.
11)Attach nishing grills over both inlet and
outlet using the two screws provided.
Fig. #7
Fig. #9
MAKE-UP AIR
KNOCKOUT
PA N E L

6
070606-8 TC36.RHKA 5056.4277
ELECTRICAL WIRING
NOTE: ALL ELECTRICAL WIRING MUST BE
DONE BY A QUALIFIED ELECTRICIAN.
Consult local codes or, in the absence of
local codes, with the current CSA C22.1 Ca-
nadian Electrical Code and in the USA with
the National Electrical Code, ANSI/NFPA 70
(Latest Edition).
SPEED
CONTROL
BLOWER
115 VOLTS
60 Hz
0.5 AMPERES
G (green)
L1 (white)
L2 (black)
Fig. #10
The Optional Remote Heat blower electrical
rating: 115V, 60HZ, 80 watts. For your protec-
tion against shock hazard, use only a properly
grounded power supply.
This kit includes a junction box, rheostat and
cover plate.The junction box should be mounted
in a convenient location away from the re-
place.

7
070606-8 TC36.RHKA 5056.4277
OPERATING INSTRUCTIONS
The wall mounted rheostat is used to turn the
blower ON and OFF, as well as to control its
speed. Please note that the blower will operate
independently to the replace. Heat will be
distributed by the blower when the replace
is on and room air will be circulated when the
replace is off.
To turn the blower on, rotate the control knob
clockwise until the switch clicks on. Continue to
rotate the knob clockwise to reduce the blower
speed.To turn the blower OFF, rotate the control
knob counter-clockwise until the switch clicks
off.
Fig. #11
MAINTENANCE
The manufacturer recommends that this kit
is cleaned at least once a year. It may be
necessary to increase the frequency of cleaning
depending on the room location, type of oor
coverings, amount of renovation work, etc.
To clean, remove the grill then use a vacuum
to clean around the blower and grill, ensuring
not to damage the fan blades.
CONTROL
KNOB

8
070606-8 TC36.RHKA 5056.4277
TECHNICAL SUPPORT: 1-877-715-2664
Web site: www.townandcountryreplaces.net
2975 Allenby Road, Duncan, BC Canada V9L 6V8