Toyomi PSF 1870 User manual

SERVICE & IMPORTANT NOTICE
INSTRUCTION MANUAL
Please read carefully and keep the instruction well
R
OSC. HIGH VELOCITY STAND FAN
MODEL: PSF 1870
220-240V~50Hz, 180W
MODEL: PSF 2070
220-240V~50Hz, 200W
CAUTION: Read and follow all instructions before operating
this fan.
Use the fan only as described in this manual. Misuse may
cause a fire or an electrical shock.
1. Close supervision is necessary, when this fan is used near
children, the elderly and pets.
2. Always turn the fan off after use, before cleaning or moving
location.
3. Do not insert fingers or other objects into the fan guard.
4. Do not operate the fan in areas where petrol, paint or other
flammable liquids are used or stored.
5. Do not place the fan near an open flame, cooking or heating
appliance, or hot surface.
6. This fan is not intended for use in wet or damp locations.
Never locate the fan in an area where it may fall into a bath or
other water container.
7. This fan should not be operated outside.
8. Always use on a dry level surface.
9. Do not let the power cord hang over the edge of a table or
counter.
10. Arrange the cord away from an area where it may be tripped
over.
11. Never place the power cord under a carpet or rug.
12. To disconnect from the power supply, grip the plug and pull
from the power socket. Never pull by the cord.
13. Do not hang or mount the fan on a wall or ceiling.
14. Do not operate if the fan guard is removed or damaged.
15. This product is designed for household and light commercial
use only.
16.Always unplug the fan before moving it, putting on or taking
off parts, cleaning, or whenever the fan is not in use. Be sure
to pull by the plug and not the cord.
SAFETY INSTRUCTIONS
If the supply cord is damaged, it must be replaced by a special cord or
assembly available from the manufacturer or its service agent.
IMPORTED BY NATIONAL ELECTRICAL TRADERS
R
R

CLEANING & MAINTENANCE
CAUTION: Always unplug the first!
The guard and stand can be easily cleaned with a soft moist
cloth and mild household cleanser. The motor bushings are
permanently lubricated at the factory and do not require any
additional lubrication.
Thank you for choosing a Oscillation high velocity
stand fan. Your new Oscillation high velocity stand fan
has been designed using the latest in technology. With
normal care and maintenance, your Oscillation high
velocity stand fan will provide years of satisfactory
performance.
R
OSCILLATION HIGH VELOCITY STAND FAN
GENERAL DESCRIPTION
OPERATING INSTRUCTIONS
MULTI - PURPOSE OF YOUR FAN
Direct:
3 Speed settings for
any cooling need.
Exhaust:
Exhausts hot, stuffy
air & pulls in fresh air.
Oscillation:
Oscillates it through
an entire room.
1.Set the fan on a dry level surface.
2. Check that the mains voltage complies with the voltage stated
on the nameplate.
3.Make sure the Speed Control is in 0 position.
4. 3 Speed Controller, switches the motor on/off and allows
choice of 3 speeds to be made:
0-Stop, 1-Low, 2-Medium, 3-High
5. Oscillation Control:
To active the oscillating setting, press down the Oscillating
Knob to stop the fan oscillating, pull up the Oscillating Knob.
6.Oscillation high velocity stand fan can be used alone or in
conjunction with an air conditioning unit to oscillation the
cooled air or to force the air into other rooms.
High Velocity Motor
Power Cord
3 Speed Controller
Rear Grille
Oscillation Knob
Blade
Adjustable Pole
Adjustable Pole
Tightening Knob
Decoration Of
The Base
Pillar
Pillar Tightening
Screws
Base
Handle
Front Grille
Plug
Logo Plate
Rear Grille Screws
Motor Shaft
R
R