TP-Link TL-POE200A User manual

7106506699 REV3.0.0
User Guide
Steady green indicates that the power
adapter is working properly.
PoE Injector:
Steady green indicates the PoE Splitter
can supply power.
PoE Injector PoE Splitter
Connection
Use the Power over Ethernet Adapter Kit to supply power and transmit data to a Non-PoE device.
PoE Splitter:
Power Socket Ethernet Device
(switch, router, etc.)
Power over Ethernet Adapter Kit
TL-POE200A (PoE Injector)
TL-POE200B (PoE Splitter)
Non-PoE Device
Power LED Explanation
Note:
Set the required voltage
of the non-PoE device
before cable connection.
12V 9V 5V
Note:TL-POE200 Power over Ethernet Kit is not compliant with IEEE 802.3af standard. The PoE Injector and PoE
Splitter can only be used together. Pairing TL-POE200A or TL-POE200B with any other devices is dangerous.
For more information, please visit our website:
http://www.tp-link.com
PoE Injector
LAN IN PWR DC 48V
PoE Injector
LAN IN PWR DC 48V
LAN OUT PWR DC OUT
PoE Splitter
LAN OUT PWR DC OUT
PoE Splitter
Package Contents: TL-POE200 Power over Ethernet Adapter Kit, Ethernet Cable, Female-to-Female Power Connector, DC Power Adapter, User Guide

Do not use this product near water, for example, in a wet basement or near a
swimming pool.
Avoid using this product during an electrical storm. There may be a remote risk
of electric shock from lightning.
SAFETY NOTICES
This is a class B product. In a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures.
CE Mark Warning
Cautions
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference
that may cause undesired operation.
Any changes or modications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
FCC STATEMENT
© 2016 TP-Link
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на
відповідність вимогам нормативних документів та вимогам, що
передбачені чинними законодавчими актами України.
Specications
IEEE 802.3, IEEE802.3i, IEEE 802.3u, CSMA/CD, TCP/IPStandards
12V, 9V or 5VVoltage Output
General Specications
Operationg Temperature 0˚C to 40˚C (32˚F to 104˚F)
Storage Temperature -40˚C to 70˚C (-40˚F to 158˚F)
Storage Humidity 5% to 90%RH non-condensing
Operationg Humidity 10% to 90%RH non-condensing
Environmental and Physical Specications
Ports TL-POE200A:
TL-POE200B:
10/100Mbps Auto-Negotiation RJ45 LAN IN port
10/100Mbps Auto-Negotiation RJ45 POWER+DATA
OUT port
DC 48V Power Input port
10/100Mbps Auto-Negotiation RJ45 POWER+DATA IN
port
10/100Mbps Auto-Negotiation RJ45 LAN OUT port
5V/9V/12V DC OUT Power Output port
UTP/STP of Cat. 5 or above (based on the standards
that the connected devices comply with)
Cable Type
Output Power 12V/1.0A, 9V/1.0A, 5V/2.0A
PWRLED
FCC, CESafety & Emissions
FAQ
A: Yes. Both the LAN ports and the PoE ports of TL-POE200 Kit comply with
IEEE 802.3 and IEEE 802.3u standards and support 10/100Mbps
Auto-Negotiation.
Q1. Can TL-POE200 Kit be used with a device which doesn’t
have a gigabit Ethernet port?
Q2. Can TL-POE200 supply power to all my non-PoE devices?
A: If the voltage standard of the devices matches that of TL-POE200 Kit,
TL-POE200 Kit can supply power to them. Ensure the Female-to-Female
Power Connector matches your non-PoE devices at the same time.
Q3. Must I use the PoE Injector together with its PoE Splitter?
A: Yes. TL-POE200 Kit is not compliant with IEEE 802.3af standard. The PoE
Injector and PoE Splitter can only be used together. Mixed use of dierent PoE
models may be dangerous.