TP-Link TL-SL3226P User manual

Rev 1.0
E-mail: [email protected]
User's GuideUser's Guide
TL-SL3226PTL-SL3226P
24+2GGigabit SwitchManaged24+2GGigabitManagedSwitch

Table of contents
Checklist...............................................................................................1
Chapter 1 About this User's Guide...................................................1
1.1 Usage..........................................................................................1
1.2 Assumpsit....................................................................................1
1.3 Overview of this User's Guide.....................................................2
Chapter 2 Introduction.......................................................................2
2.1 Overview of the product..............................................................2
2.2 Features and specification..........................................................3
2.2.1 Features......................................................................................3
2.2.2 Specification................................................................................4
Chapter 3 Installation........................................................................5
3.1 Installation...................................................................................5
3.1.1 Desktop or Shelf Installation.......................................................5
3.1.2 Rack Installation..........................................................................5
3.1.3 Power On....................................................................................6
3.2 Connecting the Switch................................................................7
3.2.1 Front Panel..................................................................................7
3.2.2 Rear Panel..................................................................................8
3.2.3 Optional Extension Modules.......................................................9
3.3 Remarks....................................................................................10
Chapter 4 TELNET/Out-of-Band Management...............................11
4.1 Introduction...............................................................................11
Trademark,Copyrightstatement
is the registered trademark of Shenzhen TP-LINK
Technologies Co., Ltd. All rights reserved, contents may be revised
withoutpriornotice.Nopartofthispublicationmaybereproducedinany
formorbyanymeansorusedtomakeanyderivativesuchastranslation,
transformation, or adaptation without permission from Shenzhen
TP-LINK Technologies Co., Ltd. See our web site for more details:
http://www.tp-link.com.

4.2 How to connect TELNET...........................................................12
4.3 How to connect Out-of-Band.....................................................13
4.4 The interface and operating way of TELNET/Out-of-Band........14
4.4.1 Configure System......................................................................17
4.4.2 Port Management......................................................................20
4.4.3 Network.....................................................................................24
4.4.4 Spanning Tree protocol.............................................................25
4.4.5 IEEE802.1X protocol.................................................................26
4.4.6 VLAN Management...................................................................27
4.4.7 Configure Trunk.........................................................................28
Chapter 5 WEB Management.........................................................29
5.1 Introduction...............................................................................29
5.2 Connection of WEB Management.............................................29
AnnexA RJ-45Plug/Connector Pin Specification.........................34
Annex B Default Configuration of the switch.................................36

Checklist
Openthebox and carefully unpack the TL-SL3226P.You should have all the
itemsonthefollowingchecklist:
!OneTL-SL3226PSwitch
!OneACpowercable
!OneSerialcable
!OneUser'sGuide(CDorPresswork)
!Twomountingbracketsandscrews
If any item is missing, contact the retailer where you purchased the TL-
SL3226Pforassistant.
Chapter1 AboutthisUser'sGuide
Thank you for purchasing TL-SL3226P 24+2G Gigabit Managed Switch.
The TL-SL3226P provide powerful management functions. With the
features of high-performance, easy-to use and economic, the TL-SL3226P
istheidealchoiceforyou.
1.1 Usage
ThisUser'sGuidetellsyouhowtouseyourTL-SL3226P.
1.2 Assumpsit
The TL-SL3226P indicated in this User's Guide is the TL-SL3226P 24+2G
GigabitManagedSwitch.
1.3 OverviewofthisUser'sGuide
Chapter1 AboutthisUser'sGuide
Chapter2 Introduction.Describestheswitchanditsfeatures
Chapter 3 Installation. Helps you to get started with the basic installation
oftheswitch
Chapter4 TELNET/Out-of-BandManagement.Describeshow tomanage
theswitchthroughTELNET/Out-of-BandManagement
Chapter5 WEBManagement
AnnexA RJ-45Plug/ConnectorPinSpecification
Annex B Default Configurationofthe switch
Chapter2 Introduction
2.1 Overviewoftheproduct
TL-SL3226P switch fully complies with IEEE802.3 Ethernet standard, its
standard19-inch size andintelligentmanagement make itsuitablefor small,
middleandlargenetworks.
TL-SL3226Pswitchprovides powerful management functions,includingthe
system,port,network,SpanningTreeprotocol,IEEE802.1Xprotocol,VLAN,
Trunk,IGMPSnooping,SNMPprotocol,priorityandsecurityetc.
TL-SL3226P switch provides multiple management method: SNMP, Web,
TelnetandConsole(RS232).
TL-SL3226P switch provides two independent extension slots, which
support100/1000M module card and GBIC. This modular structure protects
userinvestmentandmakestheswitchmoreversatile.
TL-SL3226P
24+2GGigabitManagedSwitchUser'sGuide
TL-SL3226P
24+2GGigabitManagedSwitchUser'sGuide

!Support static priority and IEEE802.1p class of service with 2-level
prioritymode
!SupportStaticMACaddressmanagementandMACaddressBinding
!Provide the configuration function of port security, broadcast storm
controlandportsniffer
!Provideperportegress/ingressratecontrolfunctionandtheminimum
granularityis64kbps
!ProvidestaticIPaddressconfigurationanddynamicIPparametersby
DHCP
!Supportfirmwareupgrade,configurationbackupandrestorebyTFTP
2.2.2 Specification
2.2 FeaturesandSpecification
2.2.1 Features
!FullycomplywithIEEE802.3standard
!Fullandhalf-duplexforboth10Mbpsand100Mbpsconnections.
!Support IEEE802.3x flow control for full-duplex mode and collision-
basedbackpressureforhalf-duplexmode
!Usenon-blockingstore-and-forwardshared-memoryarchitecture
!2410/100BaseT/TXRJ-45portswithauto-MDI/MDIX
!Provide 2 independent extension slots support 100/1000M module
cardandGBIC
!Support the port N-Way auto-negotiation function, automatically
negotiatethespeedandduplexmodebetweentwodevices
!Provide6KMACaddressspace
!Support MAC address learning and aging with programmable age
time
!ProvideIGMPsnoopingfunction
!Providemaximum26port-basedVLANand256IEEE802.1QVLAN
!Provide maximum 7 trunk groups of up to 4 member ports within 26
ports
!ProvideSNMP,WebandTelnet/Consolemanagement
!SupportSNMPv1,SNMPv2c
!Support SNMP MIB-II, Ethernet-like MIB, Bridge MIB, TP-LINK
EnterpriseMIB
!Support RMONStatistics,History,AlarmandEventgroup
!Support IEEE802.1DSpanningTreeprotocol
!Support IEEE802.1X Port-Based Network Access Control protocol
andconnecttoRADIUS
TL-SL3226P
24+2GGigabitManagedSwitchUser'sGuide
TL-SL3226P
24+2GGigabitManagedSwitchUser'sGuide
Standard Compliant with IEEE802.3, IEEE802.1D,
IEEE802.1Q and IEEE802.1X
Port 24 10/100M RJ-45 ports with auto-MDI/MDIX
2 independent 100/1000M extension slots
One console port (RS232)
VLAN Mode IEEE802.1Q VLAN mode
Port-based VLAN mode
Network Medium 10Base-T: CAT 3 or above CAT 3 UTP/STP
100Base-TX: CAT 5 UTP/STP
100Base-FX: MMF, SMF
1000Base-T: CAT 5 UTP/STP
1000Base-SX: MMF
1000Base-LX: SMF or MMF
LED Power Power on
indicator Each port Two indicators: Link/Act and 10/100Mbps
Dimension 440mm 260mm 44mm (W x H x L)
oo
Environment Operating temperature: 0 C ~ 40 C
oo
Storage temperature: -20 C ~ 70 C
Operating humidity: 10% ~ 90% RH
Storage humidity: 5% ~ 90% RH
Power 110-260V~ 50-60Hz

3.1.3 PowerOn
The TL-SL3226P can be used with the power source in the range of 110 to
260VAC,50to60Hz.
The internal power system of the TL-SL3226P can automatically adjust the
operating power-pressure according to the power-pressure input. The
POWERLEDwillbelightwhenpoweron.
Caution:
As a precaution in the event of a power failure, unplug the switch. When the
powerresumed,plugtheswitchbackin.
Chapter3 Installation
3.1 Installation
Followthesestepstoinstalltheswitch:
Thesurfacemustsupportatleast5kg
Thepowersourcemustbewithin1.5m
CheckthepowercabletomakesuretheconnectiontoACpower
Leaveenoughspacefortheventilation
3.1.1 DesktoporShelfInstallation
1. PuttheTL-SL3226Ponthebigandstabledesktop,bottomup.
2. Attachthecushioningfeetonthebottomateachcornerofthedevice.
3. Upturnthedevice,putitonthedesktop.
3.1.2 RackInstallation
TheTL-SL3226PcanbemountedinanEIA standardsize19inchrack.
1. Attach a mounting bracket to each side of the TL-SL3226P with the
screwsprovided.
2. SlidetheTL-SF3226PintotheRack.
3. UsethescrewstosecuretheTL-SL3226PtotheRack.
!
!
!
!
TL-SL3226P
24+2GGigabitManagedSwitchUser'sGuide
TL-SL3226P
24+2GGigabitManagedSwitchUser'sGuide
Figure 3-1 Rack Installation
Power
Slot1Slot2
Link/Act
TX RX
Act
FDX/Col
1000M
10/100M
Console
17192123
18202224
9111315
10121416
1357
2468
100M
24+2G Gigabit ManagedSwitch
TL-SL3226P
Link
Act

3.2 ConnectingtheSwitch
3.2.1 FrontPanel
There are 2 extension module slots, 24 10/100Mbps ports, one console
(RS232)portandLEDindicatorsonthefrontpaneloftheTL-SL3226P.
ModuleSlot
Themoduleslotscanconnect100M/1000MmodulecardandGBICcard.
2410Base-T/100Base-TXRJ-45ports
All ports can auto-negotiate between 10Mbps or 100Mbps and full or half-
duplex. You can configure the speed, duplex mode, flow control, broadcast
storm control and security control through kinds of manage-ment way such
asSNMP,Web,TelnetorOut-of-Bandmanagement.
ThereisoneLEDoneachsideofeveryport.Link/ActLEDontheleftisgreen.
100MbpsLEDontherightisorange.
Consoleport
The Console port or RS232 port on the right of the front panel is the
!
!
!
connectionportwithPCwhenOut-of-Bandmanagement.
PowerLED
Located between the console port and 24 normal ports, the power LED will
be always green when power on. Or else, please check the power
connection.
100MbpsLED(SpeedLED)
Whenanormalportconnectsto100Mbpsequipment,therespondingLEDis
orange.AnunlitLEDindicatesaconnectionspeedof10Mbps.
Link/Act(ConnectionLED)
The LEDs are lit when there is a secure connection to a device at any of the
ports.
TheflashLEDindicatesdatatransmissionattherespondingport.
3.2.2 RearPanel
Therear panel oftheTL-SL3226Pcontains a powerconnectoranda port for
groundconnection.
Powerconnector
The AC power connector is a standard three-pronged connector that
!
!
!
!
Figure 3-2 Front Panel of the TL-SL3226P
Power
Slot 1 Slot 2
Link/Act
TX RX
Act
FDX/Col
1000M
10/100M
Console
17 19 21 23
18 20 22 24
911 13 15
10 12 14 16
1357
246 8
100M
24+2G Gigabit Managed Switch
TL-SL3226P
Link
Act
TL-SL3226P
24+2GGigabitManagedSwitchUser'sGuide
TL-SL3226P
24+2GGigabitManagedSwitchUser'sGuide
Link/Act
Figure 3-3 one port of the TL-SL3226P
110-260V110-260V 50-60Hz 0.6A50-60Hz 0.6A
~
Figure 3-4 the Rear Panel of the TL-SL3226P

supportsthepower cord.Plug-inthefemaleconnector oftheprovidedpower
cord into this socket, and the male side of the cord into a power outlet.
Supportedinputvoltagerangefrom110to260VACat50-60Hz.
Theportforconnectiontotheground
Thereisaportontheleftofthepanelfortheconnectiontotheground.
3.2.3 OptionalExtensionModules
There are two module extension slots on the front panel of the TL-SL3226P
asthefollowingfigure.
Whenyouinstallanyofthemodules,youmustturnoffthepoweratfirst.After
youtakeouttheboardon theslot, putthe moduleintotheextensionslot.The
TL-SL3226Pcanauto-identifythemoduleandconfigureautomatically.
The TL-SL3226P can use with TL-SM201 100M series modules, TL-SM301
GigabitseriesmodulesandTL-SM301GBGBICcards.
TL-SM201100MSeriesModule
!
!
!TL-SM301Gigabitseriesmodule
Caution:
Theextension slots with UTPmodulecansupport auto-negotiation andauto
MDI/MDIX. These two slots are independent, never conflicting with other
normalports.
3.3 Remarks
!PayattentiontothestabilitywhenyouputtheTL-SL3226P.It'sserious
iftheTL-SL3226Pdrops.
Act
FDX/Col
Link
100M
10M
Act
FDX/Col
1000M
10/100M
Link/Act
TX RX
TL-SL3226P
24+2GGigabitManagedSwitchUser'sGuide
TL-SL3226P
24+2GGigabitManagedSwitchUser'sGuide
Figure 3-5 Module of the TL-SL3226P
Model No. Standard Interface Network Media Maximum Transfer
Distance
TL-SM201U 100Base-TX RJ-45 Cat 5 UTP/STP 100m
TL-SM201CM 100Base-FX SC 50/125 um MMF
62.5/125 um MMF 2000m
TL-SM201CS-20 100Base-FX SC 9/125 um SMF 20000m
TL-SM201CS-40 100Base-FX SC 9/125 um SMF 40000m
TL-SM201CS-60 100Base-FX SC 9/125 um SMF 60000m
Model No. Standard Interface Network Media Maximum Transfer
Distance
TL-SM301U 1000Base-T RJ-45 Cat 5 UTP 100m
TL-SM301CM 1000Base-SX SC 50/125 um MMF
62.5/125 um MMF 550m
TL-SM301CS 1000Base-LX SC 9/125 um SMF 10000m

!The TL-SL3226P can start to work with the correct power supply.
Please confirm whether the power supply is accordant to the
requirementsoftheTL-SL3226P.
!In order to avoid the risk of the power-attach, don't open the shelf of
the TL-SL3226P when it works. Don't open the shelf even without
power.
!When the TL-SL3226P is connecting with the working stop, server,
hub or other switches, the network cord must be less than 100m if the
networkcordisUTP.
!YoumustuseCat3oraboveUTPfor10Base-TEthernet.
!YoumustuseCat5UTPfor100Base-TXEthernet.
!The module decides the operating speed of the extension slot. The
100M Module can work in 100M situations, while the 1000M modules
canworkin1000Mnetworks.
!When the TL-SL3226P is working, the network cord can be put into
the port or put out from the port randomly, without breaking the
operatingoftheTL-SL3226P.
!BeforecleantheTL-SL3226P,pleaseunplugthepoweradapter.Don't
cleanwithliquid.
!Don't put the TL-SL3226P near water or humidity; avoid water or
humidityairintotheshelf.
!Avoidthedustandstrongelectromagnetism.
Chapter4 TELNET/Out-of-BandManagement
4.1 Introduction
ThroughTELNETyoucanrealizeRemoteLogintomanagetheSwitch.
Out-of-Band Management manages the Switch locally through the console
port,withoutoccupyingthebandwidth.
Though TELNET and Out-of-Band have different presentation, their
management contents are same. Both of them are to configure the Switch's
characters.
4.2 HowtoconnectTELNET
Connect the management workstation to the management port on the
Switch. You can directly use TELNET commend on the commend DOS
promptintheWindowsAttachment.
The parameter following the TELNET commend is the IP address of the
Switch which can be revised to adapt to the network. However, when you
reuse TELNET to access, the parameter will be the Switch's IP address
newlyset.
There is limit to the users accessing times through TELNET, maximum 3
times. There is also time limit for the connection. The connection will be
automaticallybrokenifthereisnooperationinalimittime.
Furthermore, maximum 5 users can access to the Switch through TELNET
atonetime.
Remark:
Only the PC connecting to the management port can configure the Switch
throughTELNETorWEB.
TL-SL3226P
24+2GGigabitManagedSwitchUser'sGuide
TL-SL3226P
24+2GGigabitManagedSwitchUser'sGuide

4.3 HowtoconnectOut-of-Band
Out-of-BandManagementneedsaterminaloraHyperTerminal.
First, connect the Switch's console port with the PC's console port by the
console cord. Then, run HyperTerminal. Refer to the following figure to
configuretheHyperTerminal.
The speed of the console port is 9600bps. The data bit is 8 bit. There is no
ParityTestandflowcontrol.TheStopbitis1.
Ifthere is no HyperTerminal inthesystem, you can setup the HyperTerminal
software from the system setup disk or download from the website such as
HyperTerminal Private Edition. The configuration way is similar with that on
Windows.
4.4 Theinterface andoperatingwayof TELNET/Out-
of-Band
No matter through TELNET or Out-of-Band Management, the users have
tworights:
!Admin: thecontrolrighttomanagetheSwitch
!Guest: thereadrightforpartofobjectsAdminvisits.
Caution
Since Guest account has the read right only for some pages, there will be a
prompt to remind the user no right for reversion when the Guest account
want to configure the active the Switch. When the account wants to enter
SNMP menu, Security menu, IEEE802.1X protocol menu, file transmission
menu and reset menu of the system configuration menu, the account will be
remindednorighttoenter.
Because the basic content of TELNET and Out-of-band Management
through the Console port is as same as each other, we introduce them
together.
Afteryouusethecorrectuser'snameandpassword(thedefaultuser'sname
and password are supervisor), you will log on the interface of TELNET/Out-
of-BandManagement.
TL-SL3226P
24+2GGigabitManagedSwitchUser'sGuide
TL-SL3226P
24+2GGigabitManagedSwitchUser'sGuide
Figure 4-1 Console configuration