TP-Link JetStream TL-SG3424 User manual

TL-SG3424
JetStream 24-Port Gigabit L2 Managed
Switch with 4 Combo SFP Slots
REV1.2.0
1910010895

COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered trademark of
TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or
registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make any
derivative such as translation, transformation, or adaptation without permission from TP-LINK
TECHNOLOGIES CO., LTD. Copyright © 2013 TP-LINK TECHNOLOGIES CO., LTD. All rights
reserved.
http://www.tp-link.com
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
Продукт сертифіковано згідно справилами системи УкрСЕПРО на відповідність вимогам
нормативних документів та вимогам, що передбачені чинними законодавчими актами
України.
I

Safety Information
When product has power button, the power button is one of the way to shut off the product;
When there is no power button, the only way to completely shut off power is to disconnect the
product or the power adapter from the power source.
Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock and
voiding the limited warranty. If you need service, please contact us.
Avoid water and wet locations.
This product can be used in the following countries:
AT BG BY CA CZ DE DK EE
ES FI FR GB GR HU IE IT
LT LV MT NL NO PL PT RO
RU SE SK TR UA
II

CONTENTS
Package Contents..........................................................................................................................1
Chapter 1 About This Guide .........................................................................................................2
1.1 Intended Readers .........................................................................................................2
1.2 Conventions..................................................................................................................2
1.3 Overview of This Guide ................................................................................................2
Chapter 2 Introduction ..................................................................................................................6
2.1 Overview of the Switch .................................................................................................6
2.2 Main Features...............................................................................................................6
2.3 Appearance Description ...............................................................................................7
2.3.1 Front Panel ........................................................................................................7
2.3.2 Rear Panel .........................................................................................................8
Chapter 3 Login to the Switch.......................................................................................................9
3.1 Login.............................................................................................................................9
3.2 Configuration .............................................................................................................. 11
Chapter 4 System .......................................................................................................................13
4.1 System Info.................................................................................................................13
4.1.1 System Summary.............................................................................................13
4.1.2 Device Description ...........................................................................................15
4.1.3 System Time ....................................................................................................15
4.1.4 Daylight Saving Time .......................................................................................16
4.1.5 System IP.........................................................................................................18
4.1.6 System IPv6.....................................................................................................19
4.2 User Management ......................................................................................................27
4.2.1 User Table........................................................................................................27
4.2.2 User Config ......................................................................................................27
4.3 System Tools ..............................................................................................................28
4.3.1 Config Restore .................................................................................................29
4.3.2 Config Backup..................................................................................................29
4.3.3 Firmware Upgrade ...........................................................................................30
4.3.4 System Reboot ................................................................................................30
4.3.5 System Reset...................................................................................................31
4.4 Access Security ..........................................................................................................31
III

4.4.1 Access Control.................................................................................................31
4.4.2 SSL Config.......................................................................................................33
4.4.3 SSH Config ......................................................................................................34
Chapter 5 Switching....................................................................................................................40
5.1 Port .............................................................................................................................40
5.1.1 Port Config .......................................................................................................40
5.1.2 Port Mirror ........................................................................................................41
5.1.3 Port Security ....................................................................................................44
5.1.4 Port Isolation ....................................................................................................46
5.1.5 Loopback Detection .........................................................................................47
5.2 LAG ............................................................................................................................48
5.2.1 LAG Table ........................................................................................................49
5.2.2 Static LAG ........................................................................................................50
5.2.3 LACP Config ....................................................................................................51
5.3 Traffic Monitor.............................................................................................................53
5.3.1 Traffic Summary...............................................................................................53
5.3.2 Traffic Statistics ................................................................................................54
5.4 MAC Address..............................................................................................................56
5.4.1 Address Table ..................................................................................................56
5.4.2 Static Address ..................................................................................................58
5.4.3 Dynamic Address .............................................................................................59
5.4.4 Filtering Address ..............................................................................................61
Chapter 6 VLAN..........................................................................................................................64
6.1 802.1Q VLAN..............................................................................................................65
6.1.1 VLAN Config ....................................................................................................67
6.1.2 Port Config .......................................................................................................69
6.2 MAC VLAN .................................................................................................................71
6.3 Protocol VLAN ............................................................................................................72
6.3.1 Protocol Group Table .......................................................................................75
6.3.2 Protocol Group.................................................................................................75
6.3.3 Protocol Template ............................................................................................76
6.4 Application Example for 802.1Q VLAN .......................................................................77
6.5 Application Example for MAC VLAN...........................................................................79
6.6 Application Example for Protocol VLAN......................................................................80
6.7 GVRP .........................................................................................................................82
IV

Chapter 7 Spanning Tree ............................................................................................................86
7.1 STP Config .................................................................................................................91
7.1.1 STP Config.......................................................................................................91
7.1.2 STP Summary..................................................................................................93
7.2 Port Config..................................................................................................................93
7.3 MSTP Instance ...........................................................................................................95
7.3.1 Region Config ..................................................................................................95
7.3.2 Instance Config ................................................................................................96
7.3.3 Instance Port Config.........................................................................................97
7.4 STP Security...............................................................................................................99
7.4.1 Port Protect ......................................................................................................99
7.4.2 TC Protect......................................................................................................102
7.5 Application Example for STP Function .....................................................................102
Chapter 8 Multicast................................................................................................................... 106
8.1 IGMP Snooping ........................................................................................................ 110
8.1.1 Snooping Config ............................................................................................ 111
8.1.2 VLAN Config .................................................................................................. 112
8.1.3 Port Config ..................................................................................................... 114
8.1.4 IP-Range........................................................................................................ 115
8.1.5 Multicast VLAN .............................................................................................. 116
8.1.6 Static Multicast IP........................................................................................... 119
8.1.7 Packet Statistics.............................................................................................121
8.2 MLD Snooping ..........................................................................................................122
8.2.1 Global Config .................................................................................................123
8.2.2 VLAN Config ..................................................................................................125
8.2.3 Filter Config....................................................................................................126
8.2.4 Port Config .....................................................................................................127
8.2.5 Static Multicast ...............................................................................................128
8.2.6 Querier Config................................................................................................128
8.2.7 Packet Statistics.............................................................................................129
8.3 Multicast Table ..........................................................................................................130
8.3.1 IPv4 Multicast Table .......................................................................................131
8.3.2 IPv6 Multicast Table .......................................................................................131
Chapter 9 QoS..........................................................................................................................133
9.1 DiffServ.....................................................................................................................136
V

9.1.1 Port Priority ....................................................................................................136
9.1.2 DSCP Priority.................................................................................................137
9.1.3 802.1P/CoS mapping.....................................................................................138
9.1.4 Schedule Mode ..............................................................................................139
9.2 Bandwidth Control ....................................................................................................140
9.2.1 Rate Limit.......................................................................................................140
9.2.2 Storm Control .................................................................................................141
9.3 Voice VLAN ..............................................................................................................143
9.3.1 Global Config .................................................................................................145
9.3.2 Port Config .....................................................................................................145
9.3.3 OUI Config .....................................................................................................147
Chapter 10 ACL ..........................................................................................................................149
10.1 Time-Range ..............................................................................................................149
10.1.1 Time-Range Summary ...................................................................................149
10.1.2 Time-Range Create........................................................................................150
10.1.3 Holiday Config................................................................................................151
10.2 ACL Config ...............................................................................................................151
10.2.1 ACL Summary................................................................................................152
10.2.2 ACL Create ....................................................................................................152
10.2.3 MAC ACL.......................................................................................................153
10.2.4 Standard-IP ACL ............................................................................................154
10.2.5 Extend-IP ACL ...............................................................................................154
10.3 Policy Config.............................................................................................................156
10.3.1 Policy Summary .............................................................................................156
10.3.2 Policy Create..................................................................................................156
10.3.3 Action Create .................................................................................................157
10.4 Policy Binding ...........................................................................................................158
10.4.1 Binding Table .................................................................................................158
10.4.2 Port Binding ...................................................................................................159
10.4.3 VLAN Binding.................................................................................................159
10.5 Application Example for ACL ....................................................................................160
Chapter 11 Network Security ......................................................................................................163
11.1 IP-MAC Binding ........................................................................................................163
11.1.1 Binding Table .................................................................................................163
11.1.2 Manual Binding ..............................................................................................164
VI

11.1.3 ARP Scanning................................................................................................166
11.1.4 DHCP Snooping.............................................................................................167
11.2 ARP Inspection .........................................................................................................173
11.2.1 ARP Detect ....................................................................................................177
11.2.2 ARP Defend ...................................................................................................178
11.2.3 ARP Statistics ................................................................................................179
11.3 DoS Defend ..............................................................................................................180
11.4 802.1X ......................................................................................................................182
11.4.1 Global Config .................................................................................................186
11.4.2 Port Config .....................................................................................................188
11.4.3 Radius Server ................................................................................................189
Chapter 12 SNMP.......................................................................................................................191
12.1 SNMP Config ............................................................................................................193
12.1.1 Global Config .................................................................................................193
12.1.2 SNMP View....................................................................................................194
12.1.3 SNMP Group..................................................................................................195
12.1.4 SNMP User ....................................................................................................196
12.1.5 SNMP Community..........................................................................................198
12.2 Notification................................................................................................................200
12.3 RMON.......................................................................................................................202
12.3.1 History Control ...............................................................................................203
12.3.2 Event Config ..................................................................................................203
12.3.3 Alarm Config ..................................................................................................204
Chapter 13 Cluster......................................................................................................................207
13.1 NDP ..........................................................................................................................208
13.1.1 Neighbor Info .................................................................................................208
13.1.2 NDP Summary ...............................................................................................209
13.1.3 NDP Config .................................................................................................... 211
13.2 NTDP........................................................................................................................212
13.2.1 Device Table ..................................................................................................212
13.2.2 NTDP Summary.............................................................................................213
13.2.3 NTDP Config..................................................................................................215
13.3 Cluster ......................................................................................................................216
13.3.1 Cluster Summary ...........................................................................................216
13.3.2 Cluster Config ................................................................................................217
VII

VIII
13.4 Application Example for Cluster Function .................................................................219
Chapter 14 Maintenance ............................................................................................................221
14.1 System Monitor.........................................................................................................221
14.1.1 CPU Monitor ..................................................................................................221
14.1.2 Memory Monitor .............................................................................................222
14.2 Log............................................................................................................................223
14.2.1 Log Table .......................................................................................................224
14.2.2 Local Log .......................................................................................................225
14.2.3 Remote Log ...................................................................................................225
14.2.4 Backup Log ....................................................................................................226
14.3 Device Diagnostics ...................................................................................................227
14.3.1 Cable Test ......................................................................................................227
14.3.2 Loopback .......................................................................................................228
14.4 Network Diagnostics .................................................................................................228
14.4.1 Ping................................................................................................................228
14.4.2 Tracert............................................................................................................229
Appendix A: Specifications .........................................................................................................231
Appendix B: Configuring the PCs ...............................................................................................232
Appendix C: Load Software Using FTP ......................................................................................237
Appendix D: 802.1X Client Software ..........................................................................................242
Appendix E: Glossary .................................................................................................................250

Package Contents
The following items should be found in your box:
One JetStream 24-Port Gigabit L2 Managed Switch with 4 Combo SFP Slots
One power cord
One console cable
Two mounting brackets and other fittings
Installation Guide
Resource CD for TL-SG3424 switch, including:
This User Guide
Other Helpful Information
Note:
Make sure that the package contains the above items. If any of the listed items are damaged or
missing, please contact your distributor.
1

Chapter 1 About This Guide
This User Guide contains information for setup and management of TL-SG3424 JetStream
24-Port Gigabit L2 Managed Switch with 4 Combo SFP Slots. Please read this guide carefully
before operation.
1.1 Intended Readers
This Guide is intended for network managers familiar with IT concepts and network terminologies.
1.2 Conventions
In this Guide the following conventions are used:
The switch or device mentioned in this Guide stands for JetStream 24-Port Gigabit L2
Managed Switch with 4 Combo SFP Slots without any explanation.
Menu Name→Submenu Name→Tab page indicates the menu structure. System→System
Info→System Summary means the System Summary page under the System Info menu
option that is located under the System menu.
Bold font indicates a button, a toolbar icon, menu or menu item.
Symbols in this Guide：
Symbol Description
Note:
Ignoring this type of note might result in a malfunction or damage to the
device.
Tips:
This format indicates important information that helps you make better use
of your device.
1.3 Overview of This Guide
Chapter Introduction
Chapter 1 About This Guide Introduces the guide structure and conventions.
Chapter 2 Introduction Introduces the features, application and appearance of the switch.
Chapter 3 Login to the Switch Introduces how to log on to the Web management page.
2

Chapter Introduction
Chapter 4 System This module is used to configure system properties of the switch.
Here mainly introduces:
System Info: Configure the description, system time and network
parameters of the switch.
User Management: Configure the user name and password for
users to log on to the Web management page with a certain
access level.
System Tools: Manage the configuration file of the switch.
Access Security: Provide different security measures for the
login to enhance the configuration management security.
Chapter 5 Switching This module is used to configure basic functions of the switch. Here
mainly introduces:
Port: Configure the basic features for the port.
LAG: Configure Link Aggregation Group. LAG is to combine a
number of ports together to make a single high-bandwidth data
path.
Traffic Monitor: Monitor the traffic of each port
MAC Address: Configure the address table of the switch.
Chapter 6 VLAN This module is used to configure VLANs to control broadcast in
LANs. Here mainly introduces:
802.1Q VLAN: Configure port-based VLAN.
MAC VLAN: Configure MAC-based VLAN without changing the
802.1Q VLAN configuration.
Protocol VLAN: Create VLANs in application layer to make some
special data transmitted in the specified VLAN.
GVRP: GVRP allows the switch to automatically add or remove
the VLANs via the dynamic VLAN registration information and
propagate the local VLAN registration information to other
switches, without having to individually configure each VLAN.
Chapter 7 Spanning Tree This module is used to configure spanning tree function of the
switch. Here mainly introduces:
STP Config: Configure and view the global settings of spanning
tree function.
Port Config: Configure CIST parameters of ports.
MSTP Instance: Configure MSTP instances.
STP Security: Configure protection function to prevent devices
from any malicious attack against STP features.
Chapter 8 Multicast This module is used to configure multicast function of the switch.
Here mainly introduces:
IGMP Snooping: Configure global parameters of IGMP Snooping
function, port properties, VLAN and multicast VLAN.
MLD Snooping: Configure global parameters of MLD Snooping
function, port properties, VLAN and multicast VLAN.
Multicast Table: View the information of IPv4 and IPv6 multicast
groups already on the switch.
3

Chapter Introduction
Chapter 9 QoS This module is used to configure QoS function to provide different
quality of service for various network applications and
requirements. Here mainly introduces:
DiffServ: Configure priorities, port priority, 802.1P priority and
DSCP priority.
Bandwidth Control: Configure rate limit feature to control the
traffic rate on each port; configure storm control feature to filter
broadcast, multicast and UL frame in the network.
Voice VLAN: Configure voice VLAN to transmit voice data
stream within the specified VLAN so as to ensure the
transmission priority of voice data stream and voice quality.
Chapter 10 ACL This module is used to configure match rules and process policies
of packets to filter packets in order to control the access of the
illegal users to the network. Here mainly introduces:
Time-Range: Configure the effective time for ACL rules.
ACL Config: ACL rules.
Policy Config: Configure operation policies.
Policy Binding: Bind the policy to a port/VLAN to take its effect on
a specific port/VLAN.
Chapter 11 Network Security This module is used to configure the multiple protection measures
for the network security. Here mainly introduces:
IP-MAC Binding: Bind the IP address, MAC address, VLAN ID
and the connected Port number of the Host together.
ARP Inspection: Configure ARP inspection feature to prevent the
network from ARP attacks.
DoS Defend: Configure DoS defend feature to prevent DoS
attack.
802.1X: Configure common access control mechanism for LAN
ports to solve mainly authentication and security problems.
Chapter 12 SNMP This module is used to configure SNMP function to provide a
management frame to monitor and maintain the network devices.
Here mainly introduces:
SNMP Config: Configure global settings of SNMP function.
Notification: Configure notification function for the management
station to monitor and process the events.
RMON: Configure RMON function to monitor network more
efficiently.
Chapter 13 Cluster This module is used to configure cluster function to central manage
the scattered devices in the network. Here mainly introduces:
NDP: Configure NDP function to get the information of the directly
connected neighbor devices.
NTDP: Configure NTDP function for the commander switch to
collect NDP information.
Cluster: Configure cluster function to establish and maintain
cluster.
4

Chapter Introduction
Chapter 14 Maintenance This module is used to assemble the commonly used system tools
to manage the switch. Here mainly introduces:
System Monitor: Monitor the memory and CPU of the switch.
Log: View configuration parameters on the switch.
Device Diagnostics: Test the connection status of the cable
connected to the switch, test if the port of the switch and the
connected device are available.
Network Diagnostics: Test if the destination is reachable and the
account of router hops from the switch to the destination.
Appendix A Specifications Lists the hardware specifications of the switch.
Appendix B Configure the PCs Introduces how to configure the PCs.
Appendix C Load Software
Using FTP
Introduces how to load firmware of the switch via FTP function.
Appendix D 802.1X Client
Software
Introduces how to use 802.1X Client Software provided for
authentication.
Appendix E Glossary Lists the glossary used in this manual.
Return to CONTENTS
5

Chapter 2 Introduction
Thanks for choosing the TL-SG3424 JetStream 24-Port Gigabit L2 Managed Switch with 4 Combo
SFP Slots!
2.1 Overview of the Switch
Designed for workgroups and departments, TL-SG3424 from TP-LINK provides wire-speed
performance and full set of layer 2 management features. It provides a variety of service features
and multiple powerful functions with high security.
The EIA-standardized framework and smart configuration capacity can provide flexible solutions
for a variable scale of networks. ACL, 802.1x and Dynamic ARP Inspection provide robust security
strategy. QoS and IGMP/MLD snooping optimize voice and video application. Link aggregation
(LACP) increases aggregated bandwidth, optimizing the transport of business critical data.
SNMP/SNMPv6, RMON, WEB/CLI/Telnet Log-in bring abundant management policies.
TL-SG3424 switch integrates multiple functions with excellent performance, and is friendly to
manage, which can fully meet the need of the users demanding higher networking performance.
2.2 Main Features
Resiliency and Availability
+ Link aggregation (LACP) increases aggregated bandwidth, optimizing the transport of
business critical data.
+ IEEE 802.1s Multiple Spanning Tree provides high link availability in multiple VLAN
environments.
+ IGMP snooping and MLD snooping automatically prevents flooding of IP multicast traffic.
+ Root Guard protects root bridge from malicious attack or configuration mistakes
Layer 2 Switching
+ GVRP (GARP VLAN Registration Protocol) allows automatic learning and dynamic
assignment of VLANs.
+ Supports up to 4K VLANs simultaneously (out of 4K VLAN IDs).
Quality of Service
+ Supports L2/L3 granular CoS with 4 priority queues per port.
+ Rate limiting confines the traffic flow accurately according to the preset value.
Security
+ Supports multiple industry standard user authentication methods such as 802.1x, RADIUS.
+ Dynamic ARP Inspection blocks ARP packets from unauthorized hosts, preventing
man-in-the-middle attacks.
+ L2/L3/L4 Access Control Lists restrict untrusted access to the protected resource.
+ Provides SSHv1/v2, SSL 2.0/3.0 and TLS v1 for access encryption for both IPv4 and IPv6.
Manageability
+ IP Clustering provides high scalability and easy Single-IP-Management.
+ Supports Telnet, CLI, SNMP v1/v2c/v3, RMON and web access.
6

+ Port Mirroring enables monitoring selected ingress/egress traffic.
+ Simple Network and Management Protocol (SNMP) can be configured over IPv6 transport.
+ IPv6 supports stateless autoconfiguration to manage link, subnet, and site addressing
changes.
+ DHCPv6 enables switch to receive configuration parameters, such as IPv6 network
addresses from DHCPv6 servers.
2.3 Appearance Description
2.3.1 Front Panel
Figure 2-1 Front Panel
The following parts are located on the front panel of the switch:
10/100/1000Mbps Ports: Designed to connect to the device with a bandwidth of 10Mbps,
100Mbps or 1000Mbps. Each has a corresponding 1000Mbps LED.
SFP Ports: Designed to install the SFP module. TL-SG3424 switch features some SFP
transceiver slots that are shared with the associated RJ45 ports. The associated two ports are
referred to as “Combo” ports, which means they cannot be used simultaneously, otherwise only
SFP ports work.
Note:
When using the SFP port with a 100M module or a gigabit module, you need to configure its
corresponding Speed and Duplex mode on Switching→Port→Port Config page. For 100M
module, please select 100MFD while select 1000MFD for gigabit module. By default, the Speed
and Duplex mode of SFP port is 1000MFD.
Console Port: Designed to connect with the serial port of a computer or terminal for monitoring
and configuring the switch.
LEDs
Name Status Indication
On Power is on.
Flashing Power supply is abnormal.
Power
Off Power is off or power supply is abnormal.
On The switch is working abnormally.
Flashing The switch is working normally.
System
Off The switch is working abnormally.
1000Mbps On A 1000Mbps device is connected to the corresponding
port.
7

Off A 10/100Mbps device or no device is connected to the
corresponding port.
On A device is connected to the corresponding port, but not
activity.
Flashing Data is being transmitted or received.
Link/Act
Off No device is connected to the corresponding port.
2.3.2 Rear Panel
The rear panel of the switch features a power socket and a Grounding Terminal (marked with ).
Figure 2-2 Rear Panel
Grounding Terminal: The switch already comes with Lightning Protection Mechanism. You
can also ground the switch through the PE (Protecting Earth) cable of AC cord or with Ground
Cable.
AC Power Socket: Connect the female connector of the power cord here, and the male
connector to the AC power outlet. Please make sure the voltage of the power supply meets the
requirement of the input voltage (100-240V~ 50/60Hz 0.6A).
Return to CONTENTS
8

Chapter 3 Login to the Switch
3.1 Login
In the IPv4 network：
1) To access the configuration utility, open a web-browser and type in the default address
http://192.168.0.1 in the address field of the browser, then press the Enter key.
Figure 3-1 Web-browser
Tips:
To log in to the switch, the IP address of your PC should be set in the same subnet addresses of
the switch. The IP address is 192.168.0.x ("x" is any number from 2 to 254), Subnet Mask is
255.255.255.0. For the detailed instructions as to how to do this, please refer to Appendix B.
2) After a moment, a login window will appear, as shown in Figure 3-2. Enter admin for the User
Name and Password, both in lower case letters. Then click the Login button or press the Enter
key.
Figure 3-2 Login
In the IPv6 network：
1) Ensure that your PC’s IPv6 function is enabled, and it’s in the same subnet with the switch.
2) To log on to the switch by the console port on the switch, please take the following steps:
1. Connect the PCs or Terminals to the console port on the switch by a provided cable.
2. Configure the Hyper terminal as illustrated in Configure the Hyper Terminal in Appendix C.
3. The DOS prompt” TL-SG3424>” will appear after pressing the Enter button as Figure 3-3
shown. It indicates that you can use the CLI now.
9

Figure 3-3 Log in the Switch
3) Type in the command enable →show ipv6 interface vlan 1 to obtain the switch’s link-local
address.
Figure 3-4 The Switch’s Link-local Address
4) Type in the switch’s link-local address with square brackets in the address field of the web
browser. Then press the Enter key.
5) After a moment, a login window will appear, as shown in . Enter admin for the User Name and
Password, both in lower case letters. Then click the Login button or press the Enter key.
10

Figure 3-5 Login
3.2 Configuration
After a successful login, the main page will appear as Figure 3-6, and you can configure the
function by clicking the setup menu on the left side of the screen.
Figure 3-6 Main Setup-Menu
11