TP-Link TL-WR741ND - Wireless Lite N Router User manual

TL-WR740N
TL-WR741ND
150Mbps Wireless N Router
REV 4.0.0
1910011
138

COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered trademark of
TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or
registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make any
derivative such as translation, transformation, or adaptation without permission from TP-LINK
TECHNOLOGIES CO., LTD. Copyright © 2014 TP-LINK TECHNOLOGIES CO., LTD. All rights
reserved.
http://www.tp-link.com

FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
•Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1）This device may not cause harmful interference.
2）This device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s authority
to operate the equipment.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This device and its antenna must not be co-located or operating in conjunction with
any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is applicable to only
Mobile Configurations. The antennas used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter.”

CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
Canadian Compliance Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject
to the following two conditions:
(1) This device may not cause interference, and
(2)This device must accept any interference, including interference that may cause undesired
operation of the device.
Cet appareil est conforme aux norms CNR exemptes de licence d’Industrie Canada. Le
fonctionnement est soumis aux deux conditions suivantes:
(1) cet appareil ne doit pas provoquer d’interférences et
(2) cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un
fonctionnement non souhaité de l’appareil.
This device has been designed to operate with the antennas listed below, and having a maximum
gain of 3 dBi. Antennas not included in this list or having a gain greater than 3 dBi are strictly
prohibited for use with this device. The required antenna impedance is 50 ohms.
To reduce potential radio interference to other users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for
successful communication.
Industry Canada Statement
Complies with the Canadian ICES-003 Class B specifications.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
This device complies with RSS 210 of Industry Canada. This Class B device meets all the
requirements of the Canadian interference-causing equipment regulations.
Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.
Korea Warning Statements
당해 무선설비는 운용중 전파혼신 가능성이 있음.

NCC Notice & BSMI Notice
注意！
依據 低功率電波輻射性電機管理辦法
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻
率、加大功率或變更原設計之特性或功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現有干擾現象時，應立
即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電信。低功率
射頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。
減少電磁波影響，請妥適使用。
安全諮詢及注意事項
●請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
●清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。
●注意防潮，請勿將水或其他液體潑灑到本產品上。
●插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。
●請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。
●請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам
нормативних документів та вимогам, що передбачені чинними законодавчими актами
України.
Safety Information
When product has power button, the power button is one of the way to shut off the product;
when there is no power button, the only way to completely shut off power is to disconnect the
product or the power adapter from the power source.
Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock
and voiding the limited warranty. If you need service, please contact us.
Avoid water and wet locations.

This product can be used in the following countries:
AT BG BY CA CZ DE DK EE
ES FI FR GB GR HU IE IT
LT LV MT NL NO PL PT RO
RU SE SK TR UA US

TP-LINK TECHNOLOGIES CO., LTD
DECLARATION OF CONFORMITY
For the following equipment:
Product Description: 150Mbps Wireless N Router
Model No.: TL-WR740N/TL-WR741ND
Trademark: TP-LINK
We declare under our own responsibility that the above products satisfy all the technical
regulations applicable to the product within the scope of Council Directives:
Directives 1999/5/EC, Directives 2004/108/EC, Directives 2006/95/EC, Directives 1999/519/EC,
Directives 2011/65/EU
The above product is in conformity with the following standards or other normative documents
EN 300 328 V1.8.1
EN 301 489-1 V1.9.2 & EN 301 489-17 V2.2.1
EN 55022: 2010 + AC: 2011
EN 55024: 2010
EN 61000-3-2: 2006 + A1: 2009 + A2: 2009
EN 61000-3-3: 2013
EN 60950-1: 2006 + A11: 2009 + A1: 2010 + A12: 2011
EN 50385: 2002
The product carries the CE Mark:
Person responsible for making this declaration:
Yang Hongliang
Product Manager of International Business
Date of issue: 2014
TP-LINK TECHNOLOGIES CO., LTD.
Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park,
Shennan Rd, Nanshan, Shenzhen, China

CONTENTS
Package Contents ............................................................................................................................. 1
Chapter 1. Introduction ...................................................................................................................2
1.1 Overview of the Router...................................................................................................2
1.2 Conventions ....................................................................................................................3
1.3 Main Features.................................................................................................................3
1.4 Panel Layout ...................................................................................................................4
1.4.1 The Front Panel ..................................................................................................4
1.4.2 The Rear Panel...................................................................................................5
Chapter 2. Connecting the Router .................................................................................................6
2.1 System Requirements ....................................................................................................6
2.2 Installation Environment Requirements.......................................................................... 6
2.3 Connecting the Router.................................................................................................... 6
Chapter 3. Quick Installation Guide...............................................................................................8
3.1 TCP/IP Configuration......................................................................................................8
3.2 Quick Installation Guide.................................................................................................. 9
Chapter 4. Configuring the Router...............................................................................................17
4.1 Login .............................................................................................................................17
4.2 Status ............................................................................................................................17
4.3 Quick Setup ..................................................................................................................18
4.4 WPS .............................................................................................................................. 18
4.5 Network......................................................................................................................... 21
4.5.1 WAN .................................................................................................................. 21
4.5.2 MAC Clone........................................................................................................29
4.5.3 LAN ................................................................................................................... 30
4.6 Wireless ........................................................................................................................ 31
4.6.1 Wireless Settings .............................................................................................. 31
4.6.2 Wireless Security ..............................................................................................33
4.6.3 Wireless MAC Filtering ..................................................................................... 36
4.6.4 Wireless Advanced ...........................................................................................39
4.6.5 Wireless Statistics ............................................................................................. 40
4.7 DHCP ............................................................................................................................ 41
4.7.1 DHCP Settings..................................................................................................41
4.7.2 DHCP Clients List .............................................................................................42
4.7.3 Address Reservation.........................................................................................43

4.8 Forwarding .................................................................................................................... 44
4.8.1 Virtual Servers...................................................................................................44
4.8.2 Port Triggering ..................................................................................................46
4.8.3 DMZ .................................................................................................................. 48
4.8.4 UPnP.................................................................................................................48
4.9 Security .........................................................................................................................49
4.9.1 Basic Security ...................................................................................................50
4.9.2 Advanced Security............................................................................................51
4.9.3 Local Management ...........................................................................................52
4.9.4 Remote Management ....................................................................................... 53
4.10 Parental Control............................................................................................................54
4.11 Access Control..............................................................................................................56
4.11.1 Rule................................................................................................................... 57
4.11.2 Host...................................................................................................................62
4.11.3 Target ................................................................................................................ 63
4.11.4 Schedule ........................................................................................................... 65
4.12 Advanced Routing ........................................................................................................67
4.12.1 Static Routing List .............................................................................................67
4.12.2 System Routing Table.......................................................................................68
4.13 Bandwidth Control.........................................................................................................69
4.13.1 Control Settings ................................................................................................69
4.13.2 Rules List ..........................................................................................................70
4.14 IP & MAC Binding Setting............................................................................................. 71
4.14.1 Binding Settings ................................................................................................71
4.14.2 ARP List ............................................................................................................ 73
4.15 Dynamic DNS ...............................................................................................................73
4.15.1 Comexe DDNS ................................................................................................. 74
4.15.2 Dyndns DDNS...................................................................................................74
4.15.3 No-IP DDNS...................................................................................................... 75
4.16 System Tools................................................................................................................. 76
4.16.1 Time Settings ....................................................................................................77
4.16.2 Diagnostic .........................................................................................................78
4.16.3 Firmware Upgrade ............................................................................................80
4.16.4 Factory Defaults................................................................................................81
4.16.5 Backup & Restore............................................................................................. 81
4.16.6 Reboot...............................................................................................................82
4.16.7 Password ..........................................................................................................82

4.16.8 System Log ....................................................................................................... 83
4.16.9 Statistics ............................................................................................................85
4.17 Logout ...........................................................................................................................87
Appendix A: FAQ.............................................................................................................................88
Appendix B: Configuring the PCs.................................................................................................93
Appendix C: Specifications ...........................................................................................................96
Appendix D: Glossary.....................................................................................................................97

TL-WR740N/TL-WR741ND
150Mbps Wireless N Router
Package Contents
The following items should be found in your package:
TL-WR740N/TL-WR741ND 150Mbps Wireless N Router
DC Power Adapter for TL-WR740N/TL-WR741ND 150Mbps Wireless N Router
Quick Installation Guide
Resource CD for TL-WR740N/TL-WR741ND 150Mbps Wireless N Router, including:
•This Guide
•Other Helpful Information

Note:
Make sure that the package contains the above items. If any of the listed items is damaged or
missing, please contact your distributor.
1

TL-WR740N/TL-WR741ND
150Mbps Wireless N Router
Chapter 1. Introduction
1.1 Overview of the Router
The TL-WR740N/TL-WR741ND 150Mbps Wireless N Router integrates 4-port Switch, Firewall,
NAT-Router and Wireless AP. The 150Mbps Wireless N Router delivers exceptional range and
speed, which can fully meet the need of Small Office/Home Office (SOHO) networks and the
users demanding higher networking performance.
The TL-WR740N/TL-WR741ND 150Mbps Wireless N Router provides up to 150Mbps wireless
connection with other 802.11n wireless clients. The incredible speed makes it ideal for handling
multiple data streams at the same time, which ensures your network stable and smooth. The
performance of this 802.11n wireless Router will give you the unexpected networking experience
at speed 650% faster than 802.11g. It is also compatible with all IEEE 802.11g and IEEE 802.11b
products.
With multiple protection measures, including SSID broadcast control and wireless LAN
64/128/152-bit WEP encryption, Wi-Fi protected Access (WPA2-PSK, WPA-PSK), as well as
advanced Firewall protections, the TL-WR740N/TL-WR741ND 150Mbps Wireless N Router
provides complete data privacy.
The TL-WR740N/TL-WR741ND 150Mbps Wireless N Router provides flexible access control, so
that parents or network administrators can establish restricted access policies for children or staff.
It also supports Virtual Server and DMZ host for Port Triggering, and then the network
administrators can manage and monitor the network in real time with the remote management
function.
Since the Router is compatible with virtually all the major operating systems, it is very easy to
manage. Quick Setup Wizard is supported and detailed instructions are provided step by step in
this user guide. Before installing the Router, please look through this guide to know all the
Router’s functions.
Simple Installation
Flexible Access Control
Multiple Security Protections
Incredible Speed
2

TL-WR740N/TL-WR741ND
150Mbps Wireless N Router
1.2 Conventions
The Router or TL-WR740N/TL-WR741ND mentioned in this guide stands for
TL-WR740N/TL-WR741ND 150Mbps Wireless N Router without any explanation.

Note:
The two devices of TL-WR740N and TL-WR741ND share this User Guide. For simplicity, we will
take TL-WR740N for example throughout this Guide.
The difference between them is:
TL-WR740N has one fixed antenna.
TL-WR741ND has one detachable antenna.
1.3 Main Features
Make use of IEEE 802.11n wireless technology to provide a wireless data rate of up to
150Mbps
One 10/100M Auto-Negotiation RJ45 WAN port, four 10/100M Auto-Negotiation RJ45 LAN
ports, supporting Auto MDI/MDIX
Provides WPA/WPA2, WPA-PSK/WPA2-PSK authentication, TKIP/AES encryption security
Shares data and Internet access for users, supporting Dynamic IP/Static IP/PPPoE Internet
access
Supports Virtual Server, Special Application and DMZ host
Supports UPnP, Dynamic DNS, Static Routing
Provides Automatic-connection and Scheduled Connection on certain time to the Internet
Connects Internet on demand and disconnects from the Internet when idle for PPPoE
Built-in NAT and DHCP server supporting static IP address distributing
Supports Stateful Packet Inspection
Supports VPN Passthrough
Supports Parental Control and Access Control
Provides 64/128/152-bit WEP encryption security and wireless LAN ACL (Access Control
List)
Supports Flow Statistics
Supports firmware upgrade and Web management
Provide a switch for the power
3

TL-WR740N/TL-WR741ND
150Mbps Wireless N Router
1.4 Panel Layout
1.4.1 The Front Panel
Figure 1-1 Front Panel sketch
The Router’s LEDs and the WPS button are located on the front panel (View from left to right).
Name Status Indication
(Power) Off Power is off.
On Power is on.
(System)
Off The router has a system error.
On 1. The router is initializing.
2. The working router has a system error.
Flashing The Router is working properly.
(WLAN)
Off
The Wireless function is disabled.
Flashing The Wireless function is working properly.
(LAN)
(WAN)
Off No device(s) are connected to the corresponding port(s).
On
There are device(s) connected to the corresponding
port(s) but no activity.
Flashing
There are device(s) connected to the corresponding
port(s) and active.
(WPS)
Slow Flash A wireless device is trying to
connect to the network via
WPS. This process may take about 2-3 minutes.
On
1.
When the system is initializing, it turns on for a short
while and then goes off.
2. When a wireless device has been successfully
conn
ected to the network via WPS, it turns on for
about 5 minutes and then goes off.
Quick
Flash
The router’s WPS times out and no wireless device
connects to the network.
Table 1-1 The LEDs description
4

TL-WR740N/TL-WR741ND
150Mbps Wireless N Router

Note:
After a device is successfully added to the network by WPS function, the WPS LED will keep on
for about 5 minutes and then turn off.
1.4.2 The Rear Panel
Figure 1-2 Rear Panel sketch
The following parts are located on the rear panel (View from left to right).
POWER: The Power socket is where you will connect the power adapter. Please use the
power adapter provided with this TL-WR740N/TL-WR741ND 150Mbps Wireless N
Router.
4/3/2/1 (LAN): These ports connect the Router to the local PC(s).
WAN:This WAN port is where you will connect the DSL/cable Modem, or Ethernet.
WPS/RESET:
Pressing this button for less than 5 seconds enables the WPS function. If your client devices,
such as wireless adapters, that support Wi-Fi Protected Setup, then you can press this button
to quickly establish a connection between the router and client devices and automatically
configure wireless security for your wireless network.
Pressing this button for more than 5 seconds enables the Reset function. With the router
powered on, press and hold the WPS/RESET button (approximately 8 seconds) until the
system LED becomes quick-flash from slow-flash. And then release the button and wait the
router to reboot to its factory default settings.
There are two ways to reset to the Router's factory defaults:
1) Use the Factory Defaults function on System Tools -> Factory Defaults page in the
Router's Web-based Utility.
2) Use the Factory Default Reset button: Press the WPS/RESET button for more than 5
seconds and then wait for the Router to reboot.
Wireless antenna: To receive and transmit the wireless data.
5

TL-WR740N/TL-WR741ND
150Mbps Wireless N Router
Chapter 2. Connecting the Router
2.1 System Requirements
Broadband Internet Access Service (DSL/Cable/Ethernet)
One DSL/Cable Modem that has an RJ45 connector (which is not necessary if the Router is
connected directly to the Ethernet.)
PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors
TCP/IP protocol on each PC
Web browser, such as Microsoft Internet Explorer 5.0 , Netscape Navigator 6.0 or above
2.2 Installation Environment Requirements
Place the Router in a well ventilated place far from any heater or heating vent
Avoid direct irradiation of any strong light (such as sunlight)
Keep at least 2 inches (5 cm) of clear space around the Router
Operating Temperature: 0℃~40℃(32℉~104℉)
Operating Humidity: 10%~90%RH, Non-condensing
2.3 Connecting the Router
Before installing the Router, make sure your PC is connected to the Internet through the
broadband service successfully. If there is any problem, please contact your ISP. After that, please
install the Router according to the following steps. Don't forget to pull out the power plug and keep
your hands dry.
1. Power off your Cable/DSL Modem, and the Router.
2. Locate an optimum location for the Router. The best place is usually at the center of your
wireless network. The place must accord with the 2.2 Installation Environment Requirements.
3. Adjust the direction of the antenna. Normally, upright is a good direction.
4. Connect the PC(s) or each Switch/Hub in your LAN to the LAN Ports on the Router, shown in
Figure 2-1. (If you have the wireless NIC and want to use the wireless function, you can skip
this step.)
5. Connect the DSL/Cable Modem to the WAN port on the Router, shown in Figure 2-1.
6. Connect the power adapter to the power socket on the Router, and the other end into an
electrical outlet. The Router will start to work automatically.
6

TL-WR740N/TL-WR741ND
150Mbps Wireless N Router
7. Power on your Cable/DSL Modem.
Figure 2-1 Hardware Installation
7

TL-WR740N/TL-WR741ND
150Mbps Wireless N Router
Chapter 3. Quick Installation Guide
This chapter will show you how to configure the basic functions of your TL-WR741ND 150Mbps
Wireless N Router using Quick Setup Wizard within minutes.
3.1 TCP/IP Configuration
The default domain name of the TL-WR741ND 150Mbps Wireless N Router is http://tplinkwifi.net,
the default IP address is 192.168.0.1, and the default Subnet Mask is 255.255.255.0. These
values can be changed as you desire. In this guide, we all use the default values for description.
Connect the local PC to the LAN ports of the Router, and then you can configure the IP address
for your PC by following the steps below:
1) Set up the TCP/IP Protocol in "Obtain an IP address automatically" mode on your PC.
If you need instructions as to how to do this, please refer to Appendix B: Configuring the
PC.
2) Then the built-in DHCP server will assign IP address for the PC.
Now, you can run the Ping command in the command prompt to verify the network connection
between your PC and the Router. The following example is in Windows 2000 OS.
Open a command prompt, and type ping 192.168.0.1, and then press Enter.
If the result displayed is similar to the Figure 3-1, it means the connection between your PC
and the Router has been established well.
Figure 3-1 Success result of Ping command
If the result displayed is similar to the Figure 3-2, it means the connection between your PC
and the Router failed.
8

TL-WR740N/TL-WR741ND
150Mbps Wireless N Router
Figure 3-2 Failure result of Ping command
Please check the connection following these steps:
1. Is the connection between your PC and the Router correct?

Note:
The 1/2/3/4 LEDs of LAN ports which you link to on the Router and LEDs on your PC's adapter
should be lit.
2. Is the TCP/IP configuration for your PC correct?

Note:
If the Router's IP address is 192.168.0.1, your PC's IP address must be within the range of
192.168.0.2 ~ 192.168.0.254.
3. Try the IP address 192.168.1.1.

Note:
If the LAN IP of the modem connected with your router is 192.168.0.x, the default LAN IP of the
Router will automatically switch from 192.168.0.1 to 192.168.1.1 to avoid IP conflict. Therefore, in
order to verify the network connection between your PC and the Router, you can open a
command prompt, and type ping 192.168.1.1, and then press Enter.
3.2 Quick Installation Guide
With a Web-based (Internet Explorer or Netscape®Navigator) utility, it is easy to configure and
manage the TL-WR741ND 150Mbps Wireless N Router. The Web-based utility can be used on
any Windows, Macintosh or UNIX OS with a Web browser.
1. To access the configuration utility, open a web-browser and type the default address
http://tplinkwifi.net in the address field of the browser.
9

TL-WR740N/TL-WR741ND
150Mbps Wireless N Router
Figure 3-3 Login the Router
After a moment, a login window will appear, similar to Figure 3-4. Enter admin for the User Name
and Password, both in lower case letters. Then click the Login button or press the Enter key.
Figure 3-4 Login Windows

Note:
If the above screen does not pop-up, it means that your Web-browser has been set to a proxy. Go
to Tools menu>Internet Options>Connections>LAN Settings, in the screen that appears, cancel
the Using Proxy checkbox, and click OK to finish it.
2. After successful login, click Next on the Quick Setup page and then you can go to quickly
configure your router.
Figure 3-5 Quick Setup
3. WAN Connection Type page will appear as shown in Figure 3-6, select a proper type and
then click Next.
10