TradeQuip 1221T User manual

Product Code: 1221T
OWNER’S MANUAL
PRODUCT CODE: 1221T
STRUT SPRING COMPRESSOR
Capacity
(Maximum)
Stroke
Spring Coil
Thickness
Spring
Length
Spring Coil
Diameter
Net Weight
1,000kg
330mm
10-18mm
210-570mm
100-158mm
36kg

Product Code: 1221T
Page 2
WARNING
IMPORTANT: READ ALL INSTRUCTIONS BEFORE USE
WARNING
The instructions and warnings contained in this manual should be read and understood before
using or operating this equipment. Do not allow anyone to use or operate this equipment until
they have read this manual and have developed a thorough understanding of how this
equipment works. Failure to observe any of the instructions contained in the manual could
result in severe personal injury to the user or bystanders, or cause damage to the equipment
and property. Keep this manual in a convenient and safe place for future reference.
Whilst every effort has been made to ensure accuracy of information contained in this manual,
the TQB Brands Pty Ltd policy of continuous improvement determines the right to make
modifications without prior warning.
CONTENT
WARNING .....................................................................................................................................2
CONTENT ......................................................................................................................................2
SAFETY INSTRUCTIONS .................................................................................................................3
ASSEMBLY, OPERATION, PREVENTITIVE MAINTENANCE..............................................................4
PARTS LIST ....................................................................................................................................9
WARRANTY .................................................................................... Error! Bookmark not defined.

Product Code: 1221T
Page 3
SAFETY INSTRUCTIONS
SAFETY OPERATNG INSTRUCTIONS
Save these instructions. For your safety, read, understand, and follow the information
provided with and on this strut spring compressor before using.
This Strut spring compressor should be used for compressing springs only.
Always securely close the spring guard before use.
No person should get any part of the body near a spring that is compressed by this
strut spring compressor.
Do not overload this strut spring compressor beyond its rated capacity. Overloading
this strut spring compressor beyond its rated capacity can cause damage to or failure
of the strut spring compressor.
Use only on hard level surfaces. Use on other than hard level surfaces can result in
strut spring compressor instability.
Keep hands & feet clear of the strut spring compressor hinge mechanism & ground
contact area when under load.
Ensure all non essential persons keep a safe distance whilst the stand is in use.
Always wear approved impact goggles, heavy duty work gloves and appropriate
clothing.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non
slip shoes.
Locate the stand in an adequate working area for its function, keep area clean and
tidy and free from unrelated materials, and ensure there is adequate lighting.
Keep the stand clean for best and safest performance.
When servicing, use only Tradequip identical replacement parts. Use of any other
parts will void the warranty.
Use the right product for the job. There are certain applications for which the Strut
spring compressor was designed. Do not modify the strut spring compressor and do
not use the strut spring compressor for a purpose for which it was not intended.
DO NOT operate unit if damaged.
DO NOT allow untrained persons to operate the strut spring compressor.
TAKE EXTREME CARE WHEN WORKING WITH A COMPRESSED SPRING:

Product Code: 1221T
Page 4
ASSEMBLY, OPERATION, PREVENTITIVE MAINTENANCE
1. FEATURES
The Tradequip Strut Spring Compressor Stand has specially designed upper jaws that
adjust up-down for clamping the spring tightly, safely, and securely. The spring
compressor adjustable base holds the strut leg very securely and it's very simple to
dismantle. The lower hydraulic clamp foot pump mechanism is easy and safe to operate
ensuring hands are free to steady load. The heavy duty safety cage offers operator safety.
Specifically designed for dismantling macpherson strut shock absorber assemblies,
applicable for most cars.
2. ASSEMBLY
Unpacking: After removing the packing material, make sure the product is in perfect
condition and that there are no visible damaged parts. The packaging materials
(Polyethylene bags, polystyrene etc.), must be disposed of responsibly in an appropriate
refuse collection container. These materials must not be left within the reach of children
as they are potential sources of danger.
1. Install on a solid flat concrete floor.
2. Anchor the unit to the floor utilising the four holes in the base plate. Make sure
there is no movement between the base plate and floor.
3. BEFORE USE
Inspect before use and do not use this spring compressor if parts are loose or damaged.
Strut Spring Compressor stand should be bolted to the workshop floor before use.
Apply grease to the front and rear faces of the main upright to assist the smooth sliding of
upper and lower strut support rollers.
Conduct a visual inspection of spring compressor and ensure pins are securely positioned
and that there is no sign of wear or fatigue. If found, do not use the unit until it is repaired
by an authorised technician.

Product Code: 1221T
Page 5
4. OPERATION
Disassemble the Strut Assembly
1. Adjust the upper spring support arm and shoe assembly on the spring compressor
stand to the desired height of the strut spring so that the complete strut assembly
can be clamped firmly in place via the desired coils of the spring.
2. Ensure upper and lower shoes, spring support bars and retaining pins are properly
secured.
3. Ensure appropriate spring coils are securely seated in the correct upper and lower
spring shoes and cannot slide out during compression.
4. Close the spring compressor safety cage
5. When compressing the spring the operator must always stand to the side of the
spring compressor.
6. Before attempting to remove the top cap nut, always use some type of tool to test
that the compression on the nut and washer has been relieved. DO NOT use fingers
7. Remove nut and washer and lower strut assembly clear of spring.
8. Immediately release tension on the spring by depressing the release pedal. NEVER
leave compressed spring unattended.
WARNING! TAKE EXTREME CARE WHEN WORKING WITH A COMPRESSED SPRING
Assemble the Strut Assembly
1. Adjust the upper spring support bars and correct size shoe assembly to the desired
height of the strut spring so that the spring can be clamped firmly in place.
2. Ensure upper and lower shoes, strut supports and retaining pins are properly
secured.
3. Ensure the upper and lower coil of the spring is securely seated in the correct upper
and lower spring shoes and cannot slide out during compression.
4. Close the spring compressor safety cage
5. When compressing the spring the operator must always stand to the side of the
spring compressor. NEVER leave compressed spring unattended.
6. Compress the spring by depressing the foot pedal, until the threaded cap nut and
washer can be wound onto the threaded strut rod when the strut assembly is
reassembled. NUT MUST BE FULLY ENGAGED ON PISTON ROD THREADS!
7. Before releasing the tension on the spring, ensure that the cap nut is securely
fastened according to vehicle manufacturer specifications.
8. From the rear or side of the unit, Release the compression tension slowly by
depressing the release pedal, keeping hands and fingers away from the compressed
spring assembly
9. Be sure the tension on the spring is securely held by the strut assembly and cap nut
before opening the safety cage and removing the strut assembly from the upper and
lower shoes of the spring compressor stand.

Product Code: 1221T
Page 6
WARNING! DO NOT OVER COMPRESS SPRING!
NOTE: When replacing top spring seat or spring, make note of the position of the spring seat
and spring before releasing spring from tool. Replace new strut parts in tool in the same
position as the old.
5. STORAGE
This strut spring compressor should always be stored in a dry location on a level surface.
6. MAINTENANCE
Inspect the product for damage, wear, broken or missing parts and that all components
function before each use. Remove from service immediately if damaged in any way.
NOTE: To avoid personal injury or damage, permit only qualified personnel to perform
maintenance. See repair parts breakdown for replacement parts.
•ALWAYS: Keep coil seats free of oil and grease.
•DAILY: Inspect hydraulic unit, hooks, posts, lock pins and slots for wear.
•MONTHLY: Wipe down and clean drive screw, and hydraulic unit.
•PERIODICALLY: Inspect unit for loose or missing components.
•YEARLY: Clean and lightly lubricate all moving parts.
7. SERVICE & REPAIR
Any strut spring compressor found damaged in any way, or found to be worn or operates
abnormally should be removed from service until repaired by an authorised service agent.
Owners and / or operators should be aware that repair of this product may require
specialised equipment and knowledge. Only authorised parts, labels, decals shall be used
on this equipment. Annual inspection of the strut spring compressor is recommended
and can be made by an authorised repair facility to ensure that your equipment is in
optimum condition and that the equipment has the correct decals and safety labels
specified by the manufacturer.

Product Code: 1221T
Page 7

Product Code: 1221T
Page 8
PARTS DIAGRAM

Product Code: 1221T
Page 9
PARTS LIST
Part
#
Description
QTY
Part
#
Description
QTY
1
Frame
1
26
Ram
1
2
Base Support
2
27
Gasket
1
3
Washers
4
28
Seal Ring
1
4
Nuts
4
29
Ball
3
5
Bolts
4
30
Release Rod
1
6
Strut Support
1
31
Seal Ring
1
7
Roller
3
32
Spring
1
8
Circlip
10
33
Release Pedal
1
9
Cover
1
34
Valve Block
1
10
Pin Roller
2
35
Roller
1
11
Roller
2
36
Pedal
1
12
R-Pin
4
37
Roller
2
13
Large Shoes
2
38
Handle Socket
1
14
Strut Support
1
39
Circlip
3
15
Roller
4
40
Piston
1
16
Washer
4
41
Connecting Rod
1
17
Bolt
1
42
Circlip
1
18
O-Ring
1
43
Seal Ring
1
19
Bushing
1
44
Spring
1
20
Nylon Ring
1
45
Spring
1
21
Piston
1
46
Piston Base
1
22
Piston Head
1
47
Gasket
1
23
Washer
1
48
Small Shoe
2
24
O-Ring
1
49
Chain
1
25
Cylinder
1
50
Guard
1

Product Code: 1221T
Page 10
WARRANTY
Tradequip products have been carefully tested and inspected before shipment and are
guaranteed to be free from defective materials and workmanship for a period of 12 months
from the date of purchase except where tools are hired out when the guarantee period is
ninety days from the date of purchase.
Should this piece of equipment develop any fault, please return the complete tool to your
nearest authorised warranty repair agent or contact TQB Brands Pty Ltd Warranty team –
[email protected].
If upon inspection it is found that the fault occurring is due to defective materials or
workmanship, repairs will be carried out free of charge. This guarantee does not apply to
normal wear and tear, nor does it cover any damage caused by misuse, careless or unsafe
handling, alterations, accident, or repairs attempted or made by any personnel other than the
authorised TQB Brands Pty Ltd repair agent.
This guarantee applies in lieu of any other guarantee expressed or implied and variations of its
terms are not authorised.
Your TQB Brands Pty Ltd guarantee is not effective unless you can produce upon request a
dated receipt or invoice to verify your proof of purchase within the 12 month period.
Consumer Guarantee
Our goods come with a guarantee that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and compensation for any
other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the failure does not amount to a
major failure.