Tranberg TEF 2920 User manual

Tranberg AS | P.O. Box 8033 | N-4068 Stavanger | Norway | Tel.: [phone] | Fax.: [phone]
E-mail: [email protected] | www.tranberg.com
Tranberg Systems | Hjulmagervej 15C | 7100 Vejle | Denmark | Tel.: [phone]
E-mail: [email protected] | www.tranbergsystems.com
TEF 2920
XENON FLASHLIGHT
USER MANUAL
IMPORTANT
Read this instruction carefully before installing the
product
TUM 1020
2438

TEF 2920 XENON FLASHLIGHT USER MANUAL
INTRODUCTION
Thank you for purchasing this product!
For installation, maintenance and assurance of a long life
of this product, please follow this manual.
CONTENT IN BOX
The product is fully assembled, and ready for installation.
SAFETY PRECAUTIONS
Note that changes made to the product and/or installation
of components which do not conform to the approval, may
be a safety violation. The manufacturer will in no circum-
stance be held responsible for such activity.
For your health and safety, always use safety gear suited
for the task. Be certain to follow codes, regulations and/or
specific procedures that are related to the installation.
TOOLS REQUIRED
Regular tools required for installation:
10 mm wrench –for assembling the luminaire
27 mm wrench –for cable gland.
24 mm wrench –for tightening the pressure nut.
6,5 mm flat screwdriver –for earth screw.
•
•
•
•
MAINTENANCE INSTRUCTIONS
The luminaire should be inspected according to Company
routines. The manufacturer suggests regular check for wa-
ter intrusion/condensation which should be removed imme-
diately. Check the drain plug / drain hole function.
When cleaning, use only mild detergents. Alcohol or pe-
troleum based products may damage lens, paint or plastic
components.
RUBBER SEAL
Cable diameter Size Part No.
5 - 9mm Ø20,4/9,0x8mm 5002 0045
8,5 - 14mm Ø20,5/13,0x8mm 5002 0038
Be sure to install the cable in a way wich prevents water to penetrate into the enclosure through the cable gland,
also make sure to use the correct rubber seal when you install the luminaire
APPLICATIONS
Signal lighting
Obstacle marking
Safe area
•
•
•
APPROVALS
NA

TEF 2920 XENON FLASHLIGHT USER MANUAL
INSTALLATION INSTRUCTIONS
SPARE PARTS
Description Part No.
Flashing insert, 230V 2943
Flashing insert, 120V 3083
Globe without gasket, clear 5044 0018
Globe without gasket, green 5044 1006
Globe without gasket, red 5044 2006
Globe without gasket, blue 5044 4004
Globe without gasket, yellow/amber 5044 6001
Globe without gasket, yellow 5044 3004
Globe gasket 5001 0021
Guard, 2438N (2889) 2000 037
Cable gland, M20 marine 7045 043
Stopping plug, M20 marine 7945 001
Prior to the installation, remove the globe of the
luminaire. This is done by turning the globe ring/guard
counter clockwise, and then pull out both the guard and
the globe. Ensure that the silicon gasket stay on the globe
flange, as it is vital to obtain the water ingress protection.
The lamp is fastened to a structure typically by means of
two M5 bolts, spaced at 120mm. If installed on a wall,
ensure that the cable gland is pointing downwards to
minimize the risk of water ingress through the cable
gland.
Remove the bottom assembly plate inside the luminaire.
This is done by only loosening the two M3 screws, then
slightly turning the bottom assembly plate until it can be
pulled out.
Check that the rubber gasket inside the cable gland
matches the dimension of the cable. See the section at
bottom of the preceding page in this manual, and swicth
to a different size if required. Pull the cable through the
cable gland and connect the wires to the terminals on the
bottom assembly plate.
Replace the bottom assembly plate, while ensuring that
the cable and wires beneath it, does not get jammed when
the two screws for the bottom assembly plate are
tightened. Then tighten the cable gland nut until the
rubber gasket is firmly sealing against the cable.
Finally, test the lamp, then replace the globe and the globe
ring/guard. Please ensure that the silicon gasket is free
from foreign objects and that it is not twisted, nor
dislocated, as that may impair the water ingress rating of
the product.
Mount on plane surface, or on pipe 1”BSP (code 0)

Tranberg AS | P.O. Box 8033 | N-4068 Stavanger | Norway | Tel.: [phone] | Fax.: [phone]
E-mail: [email protected] | www.tranberg.com
Tranberg Systems | Hjulmagervej 15C | 7100 Vejle | Denmark | Tel.: [phone]
E-mail: [email protected] | www.tranbergsystems.com
TEF 2920 XENON FLASHLIGHT USER MANUAL
TECHNICAL DATA
Material: Cast copper alloy
Input voltage: 210/250V AC or 110/130V AC
Flash rate: 60/120/180 flash pr. min. 230V AC
Light energy: Approx. 10 joule dependant on flash rate
IP-rating: IP 56
Weight: 1,8 kg.