Trane BAYECON085A Assembly instructions

January 2010 ACC-SVN44D-EN
Installer’s Guide
Economizer
Packaged Rooftop Units
Model Number: Used With:
BAYECON085A TSC/YSC036E-060E*R WSC060EDR
THC/YHC036E*R
WSC036E-048E*R
BAYECON086A THC/YHC036E*E TSC/YSC036E-060E*E
BAYECON087A THC/YHC048E-120E*R WSC060E(3/4/W)R
TSC072E-120E*R WSC072E-120E*R
YSC072E-120E*R
BAYECON088A THC/YHC048E-120E*E
TSC072-120E*E
YSC072-120E*E

© 2010 Trane All rights reserved ACC-SVN44D-EN
Warnings, Cautions and Notices
Warnings, Cautions and Notices. Note that warnings, cautions and notices appear at
appropriate intervals throughout this manual. Warnings are provided to alert installing contractors
to potential hazards that could result in personal injury or death. Cautions are designed to alert
personnel to hazardous situations that could result in personal injury, while notices indicate a
situation that could result in equipment or property-damage-only accidents.
Your personal safety and the proper operation of this machine depend upon the strict observance
of these precautions.
Important
Environmental Concerns!
Scientific research has shown that certain man-made chemicals can affect the earth's naturally
occurring stratospheric ozone layer when released to the atmosphere. In particular, several of the
identified chemicals that may affect the ozone layer are refrigerants that contain Chlorine, Fluorine
and Carbon (CFCs) and those containing Hydrogen, Chlorine, Fluorine and Carbon (HCFCs). Not all
refrigerants containing these compounds have the same potential impact to the environment.
Trane advocates the responsible handling of all refrigerants-including industry replacements for
CFCs such as HCFCs and HFCs.
Responsible Refrigerant Practices!
Trane believes that responsible refrigerant practices are important to the environment, our
customers, and the air conditioning industry. All technicians who handle refrigerants must be
certified. The Federal Clean Air Act (Section 608) sets forth the requirements for handling,
reclaiming, recovering and recycling of certain refrigerants and the equipment that is used in these
service procedures. In addition, some states or municipalities may have additional requirements
that must also be adhered to for responsible management of refrigerants. Know the applicable
laws and follow them.
WARNING
Personal Protective Equipment (PPE) Required!
Installing/servicing this unit could result in exposure to electrical, mechanical and chemical
hazards.
• Before installing/servicing this unit, technicians MUST put on all Personal Protective
Equipment (PPE) recommended for the work being undertaken. ALWAYS refer to appropriate
MSDS sheets and OSHA guidelines for proper PPE.
• When working with or around hazardous chemicals, ALWAYS refer to the appropriate MSDS
sheets and OSHA guidelines for information on allowable personal exposure levels, proper
respiratory protection and handling recommendations.
• If there is a risk of arc or flash, technicians MUST put on all necessary Personal Protective
Equipment (PPE) in accordance with NFPA70E for arc/flash protection PRIOR to servicing the
unit.
Failure to follow recommendations could result in death or serious injury.
ATTENTION: Warnings, Cautions and Notices appear at appropriate sections throughout
this literature. Read these carefully.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, could
result in minor or moderate injury. It could also be used to alert against unsafe practices.
NOTICE:Indicates a situation that could result in equipment or property-damage-only
accidents.

Table of Contents
ACC-SVN44D-EN 3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Model Number Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installation - Field Installed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Downflow Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Horizontal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Optional Sensors (ReliaTel Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Blockoff Asssembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Wiring Connections ReliaTel Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Electromechanical Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Factory Installed Economizer Set-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Downflow Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Horizontal Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Minimum Position Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Dry Bulb Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Reference Enthalpy Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

4ACC-SVN44D-EN
Installation
Model Number Description
All products are identified by a multiple-character model number that precisely identifies a
particular type of unit. Its use will enable the owner/operator, installing contractors, and service
engineers to define the operation, specific components, and other options for any specific unit.
When ordering replacement parts or requesting service, be sure to refer to the specific model
number and serial number printed on the unit nameplate.
Parts List
• 1 - Economizer Assembly
• 1 - Mist Eliminator
• 10 - Screws (T/YSC036-060E, T/YHC036E, WSC036-048E, and WSC060ED)
• 12 - Screws (T/YSC072E-120E, T/YHC048-120E, WSC060E(3/4/W), and WSC072-120E)
• 1 - Sensor; Thermistor
•1-Grommet
• 1 - Tie; Wire
• 1 - Barometric Duct Blockoff Plate
Installation - Field Installed
Note: This instruction covers installation of BAYECON085A, BAYECON086A (T/YSC036-060E, T/
YHC036E, WSC036-048E, and WSC060ED) and BAYECON087A, BAYECON088A (T/
YSC072E-120E, T/YHC048-120E, WSC060E(3/4/W), and WSC072-120E).
WARNING
Hazardous Voltage!
Disconnect all electric power, including remote disconnects before servicing. Follow proper
lockout/tagout procedures to ensure the power can not be inadvertently energized. Failure to
disconnect power before servicing could result in death or serious injury.
Uncrate the economizer and locate all parts shown in Figure 1, p. 5.
Each economizer ships with items 1, 2 and 3 attached. Remove screws completely from items 1 and
2. Remove item 3 by loosening the 3 screws but do not remove them. Refer to Figure 1, p. 5.

ACC-SVN44D-EN 5
Installation
Remove unit end panel, retain the screws removed from the top of panel and the screws removed
from bottom of panel for use later.
Downflow Installation
For Downflow Installation, assemble end panel to the economizer. Refer to Figure 2.
Horizontal Installation
For Horizontal Installation, assemble end panel to the economizer. Refer to Figure 3 for
disassembly instructions of the downflow configuration.
Figure 1.
Figure 2.

6ACC-SVN44D-EN
Installation
Refer to Figure 4 for reassembly instructions to Horizontal configuration.
Optional Sensors (ReliaTel Only)
If the optional sensors for humidity and temperature monitoring are to be used (BAYENTH005A
and BAYENTH006B), install them now. Use the instructions provided in the kits.)
Blockoff Asssembly
The return duct blockoff plate(s) must be installed prior to the installation of the economizer in the
unit. Refer to Figure 5 for installation in units without Return Air Smoke Detector. If the unit has a
Return Air Smoke Detector, refer to Figure 6 for installation.
Note: If either Power Exhaust or Barometric Relief Accessory kits are installed along with an
Economizer, do not install the duct blockoff plate.
Figure 3.
Figure 4.

ACC-SVN44D-EN 7
Installation
Note: On (T/YSC072E-120E, T/YHC048-120E, WSC060E(3/4/W), and WSC072-120E) downflow
units only, install return air blockoff. See Figure 6.
To install the economizer, lift into position by fitting the upper left hand corner around the channel
in the cabinet post. Then pivot the economizer into the opening in the cabinet.
Once the economizer is in place, lift the economizer and panel assembly to align the upper two
screw holes. Secure the top by inserting 2 screws, top left 1 then top right 2 screws.
Pull out on the bottom of the economizer and secure bottom left 3 screws.
Remove the filter access panel. Position the adapter backing plate inside the filter section. The
adapter backing plate will slip over the 3 screws that were loosened in Figure 1, p. 5. Align the screw
engagement hole in the adapter backing plate, with the screw clearance hole in panel and secure
lower right side of economizer with screw 4.
Install the bottom blockoff and secure with 3 screws.
Figure 5.
Figure 6.
Note: IfPower Exhaust
or Barometric Relief
accessory kits are installed
along with an Economizer,
do not install duct blockoff
plate
Note: IfPower Exhaust
or Barometric Relief
accessory kits are installed
along with an Economizer,
do not install duct blockoff
plate

8ACC-SVN44D-EN
Installation
Install the Mixed Air Sensor with grommet, secure with pop-in wire tie. Connect to exiting
jumper connections located in the Indoor Fan Section.
Wiring Connections ReliaTel Units
Locate unit wiring harness plug P7 and plug into J7 on the actuator motor.
Note: If Options Module (RTOM) is not installed then connect plug 3P4 to 3J4 on the Refrigeration
Module (RTRM) in the control box.
Electromechanical Units
Locate unit wiring harness plug PPM2A and plug into the actuator motor wiring harness.
Replace access panels.
Figure 7. Mixed Air Sensor figure for units with FC fan (All units except Y/TSC120E(3/4/W), Y/
THC092-120E, WSC120E(3/4/W)
Figure 8. Mixed Air Sensor for units with Plenum fan (Y/TSC120E(3/4/W), Y/THC092-120E,
WSC120E(3/4/W)

ACC-SVN44D-EN 9
Installation
Factory Installed Economizer Set-Up
Downflow Configuration
To position economizer for Downflow operation, complete the following steps:
WARNING
Hazardous Voltage!
Disconnect all electric power, including remote disconnects before servicing. Follow proper
lockout/tagout procedures to ensure the power can not be inadvertently energized. Failure to
disconnect power before servicing could result in death or serious injury.
1. Remove filter access panel.
2. Remove bottom blockoff from its shipping location. See Figure 9.
3. Remove the bottom three screws from the economizer panel.
4. Pull the economizer assembly out into operating position as shown in Figure 10.
5. Secure the economizer assembly with 2 screws at the bottom of the corner posts.
6. Install bottom blockoff and secure with 3 screws.
Figure 9.
Figure 10.

10 ACC-SVN44D-EN
Installation
7. Using field supplied silicone, apply sealant around economizer hood as shown in Figure 11
below.
Horizontal Configuration
To position economizer for horizontal operation, complete the following steps:
1. Remove filter access panel.
2. Remove item 3, adapter panel shown in Figure 1, p. 5.
3. Remove the bottom three screws and top two screws from the economizer panel.
4. Remove return air blockoff.
5. Pull the economizer assembly and end panel out of the unit.
6. Refer to Figure 3, p. 6 and Figure 4, p. 6 for reassembly instructions to Horizontal configuration.
Note: (ReliaTel units only) If optional sensors for humidity and temperature monitoring are to be
used (BAYENTH005A and BAYENTH006B), install them now. Use the instructions provided
in the kits.)
7. Remove supply and return duct covers from the horizontal openings and install over the
downflow opening.
8. To reinstall the economizer, lift into position by fitting the upper left hand corner around the
channel in the cabinet post. Then pivot the economizer into the opening in the cabinet.
9. Lift the economizer and panel assembly to align the upper two screw holes. Secure the top by
inserting 2 screws, top left 1 then top right 2.
10. Pull out on the bottom of the economizer and secure bottom left 3.
11. Replace adapter panel removed in Step 2.
12. Secure bottom right with screw engaging into adapter panel.
13. Install the bottom blockoff and secure with 3 screws. Refer to Figure 10, p. 9.
14. Using field supplied silicone, apply sealant around economizer hood as shown in Figure 11.
Figure 11.