Transcend TS-UWL31 User manual

TS-UWL31
TS-UWH31
TS-UWE31
USER/S MANUAL
Intel
®
Socket 370 CeleronTM /
Pentiu
®
III FC-PGA Series
Your Supplier, Your Partner,
Your Friend.
Transcend

TS-UWL31/TS-UWH31/TS-UWE31 Motherboard
Supporting Intel ® Socket 370 CeleronTM / Pemtium® III FC-PGA Processor Series
66/ 00/ 33MHz Front Side Bus
Intel® 8 0 Chipset
Welco e !!
Congratulations on your purchase of this great value motherboard, with its range of special
features and innovative onboard functions, built around the advanced architecture of the new
Intel® 8 0 series Chipset. More details to follow later in this manual.
Our Website
Please come and visit us at our website on http://www.transcendusa.com/ Youll find plenty of
interesting information about this and many other quality Transcend products.
Your Users Manual
This Users Manual is designed to help end users and system manufacturers to set up and
install the motherboard. All of the information within has been carefully checked for accuracy.
However, Transcend Information, Inc. (hereafter referred to as Transcend) carries no
responsibility or liability for any errors or inaccuracies which this manual may contain. This
includes references to products and software. In addition, the information and specifications
are subject to change without prior notice.
Disclai er
Transcend provides this manual as is without any warranty of any kind, either expressed or
implied, including  but not limited to  the implied warranties, conditions of merchantability or
fitness for a particular purpose. Transcend, its management, employees, distributors and
agents are in no way liable for any indirect special, incidental or consequential damages,
including loss of profits, loss of business and the like. This is even if Transcend has been
advised of the possibility of such damages arising from any defect or error in this manual or
product.
Trade arks
All brands, product names and trademarks mentioned in this document are the property of
their respective owners or companies and are used solely for identification or explanation. It
is Transcend policy to respect all product rights.
Copyright
This manual may not, in whole or in part, be photocopied, reproduced, transcribed, translated
or transmitted, in whatever form or language, without the written consent of the manufacturer,
except for copies retained by the purchaser for personal archiving purposes.
Manual Version: .0
Release Date: January,2000
Copyright © July 999 Transcend Information, Inc.

Table of Contents
CHAPTER 1 INTRODUCTION 1
. Essential Handling Precautions.......................................................................
.2 Checklist: Hardware Required for Setup..........................................................2
.3 Package Contents..........................................................................................2
.4 Specifications and Features.............................................................................3
CHAPTER 2 HARDWARE INSTALLATION 5
2. Transcend TS-UWL3 /TS-UWH3 /TS-UWE3 Motherboard............................5
2.2 Layout of Transcend TS-UWL3 /TS-UWH3 /TS-UWE3 Motherboard.................6
2.3 CPU Installation..............................................................................................7
2.4 66/ 00/ 33MHz System configuration.................................................................9
2.5 Memory Configuration.................................................................................. 0
2.6 Keyboard Wake Up......................................................................................
2.7 Primary / Secondary IDE Connectors............................................................ 2
2.8 Floppy Disk Drive Connector........................................................................ 3
2.9 Fan Power Connectors................................................................................ 4
2. 0 Wake-on-LAN Connector.............................................................................. 5
2. IrDA-Compliant Infrared Module Connector.................................................... 6
2. 2 Panel Connectors......................................................................................... 7
2. 3 Power Connector......................................................................................... 9
2. 4 External Back Panel I/O Ports........................................................................20
2. 5 Clear CMOS Jumper....................................................................................2
2. 6 FWH Lock Jumper........................................................................................22
2. 7 Onboard Audio Setting..................................................................................23
2. 8 Internal Audio Connectors............................................................................24

2. 9 Internal Serial Port Connector COMB ..........................................................25
2.20 VIO Adjust Jumper.............................................................................................26
CHAPTER 3 BIOS SETUP 27
3. BIOS Setup ............................................................................................... 27
3.2 The Main Menu ......................................................................................... 27
3.3 Standard CMOS Features........................................................................... 29
3.4 Advanced BIOS Features............................................................................ 32
3.5 Advanced Chipset Features ........................................................................ 35
3.6 Integrated Peripherals .................................................................................37
3.7 Power Management Setup...........................................................................4
3.8 PnP/PCI Configuration Setup....................................................................... 44
3.9 PC Health Status ........................................................................................46
3. 0 Frequency/Voltage Control..........................................................................47
3. Load Fail-Safe Default.................................................................................48
3. 2 Load Optimized Defaults.............................................................................48
3. 3 Supervisor Password..................................................................................49
3. 4 User Password...........................................................................................50
3. 5 Save & Exit Setup.......................................................................................50
3. 6 Exit Without Saving ................................................................................... 5
CHAPTER 4 SOFTWARE SETUP 52
4. INF Update for 8 0 Chipset ....................................................................... 52
4.2 VGA Driver Setup.......................................................................................53
4.3 Intel Security Controller Driver.....................................................................54
4.4 Audio Driver Setup.......................................................................................55
CHAPTER 5 BIOS UPGRADE 60
5. How to Check Your BIOS File Name and Version ........................................ 60
5.2 How to Download the Correct BIOS File from the Web..................................... 60
5.3 How to Upgrade Your Motherboard BIOS ......................................................... 6

INTRODUCTION 1
CHAPTER 1 INTRODUCTION
1.1 Essential Handling Precautions
IMPORTANT. Read this page before unpacking your motherboard!
• Power Supply
Be careful! Always ensure that the computer is disconnected from the power supply when
working on the motherboard and its components.
• Static
Static electricity may cause damage to the delicate integrated circuit chips on your motherboard.
Before handling the motherboard outside of its protective packaging, ensure that there is no
static electric charge in your body. To avoid this risk, please observe these simple precautions
while handling the motherboard and other computer components:
. If possible, wear an anti-static wrist strap. This fits around your wrist and is connected to
a natural earth ground.
2. Touch a grounded or anti-static surface, or a metal fixture such as a pipe or the chassis of
your system, before touching the motherboard.
3. When you have removed the motherboard from its anti-static packaging, try to hold it only
by the edges, without touching any components.
4. Avoid contacting the components on add-on cards, motherboards, and modules with the
golden fingers (gold-colored connectors) which plug into the expansion slots.
5. It is safest to handle system components only by their mounting brackets.
6. Keep components which are not connected to the system in the anti-static packaging
whenever possible.
These precautions help to reduce the risk of static build-up and ensure any static discharge is
harmless to your equipment.
••
••
• Battery Replace ent
The battery which holds the system settings memory on your motherboard should not
require replacement for at least five years, and probably much longer. In picture 2.2, it is
located near the bottom right hand corner.

Please replace your battery only with the same type, or a similar type recommended by the
manufacturer. If the battery is replaced incorrectly, there is a risk of a short circuit or explosion.
Used batteries should disposed of according to the manufacturers instructions.
••
••
• Electric Screwdrivers
To reduce the risk of damage to the motherboard due to excessive torque, avoid setting
electric screwdrivers above 7.5 kg/cm.
1.2 Checklist: Hardware Required for Setup
It is advisable to have all of these items of hardware available before you unpack your
motherboard from its anti-static packaging and start building your system.
- Computer case and chassis with appropriate power supply.
- Monitor.
- Socket 370 Central Processing Unit.
- DIMM memory module.
- PS/2 or USB Keyboard.
- PS/2 or USB Mouse.
- Hard Disk Drive.
- Floppy Disk Drive.
- CD-ROM Drive.
- (Optional) External Peripherals: printer, speakers, plotter, modem.
- (Optional) Internal Peripherals: modem, LAN cards.
1.3 Package Contents
This motherboard package should contain the following items. Please check them as soon as
you unpack. If you find any damaged or missing items, please contact your retailer.
- TS-UWL3 /TS-UWH3 /TS-UWE3 motherboard
- X CD-ROM
- X FDD cable
- Users Manual
- COM port cable x
- Ultra DMA / 66 cable x
2 INTRODUCTION

1.4 Specifications and Features
• •
• •
• CPU
- Supports Intel® Socket 370 CeleronTM / Pentium® III FC-PGA Series
• •
• •
• Chipset
- TS-UWL3 : Intel® 8 0 Chipset
- TS-UWH3 : Intel® 8 0- DC 00 Chipset
- TS-UWE3 : Intel® 8 0E Chipset
• •
• •
• Display Cache Me ory
- 4MB Display Cache 00/ 33MHz SDRAM (TS-UWH3 /TS-UWE3 )
• •
• •
• DRAM Me ory
- Supports Synchronous DRAM
- 2 x 68-pin DIMM module sockets on board
- 8~5 2MB memory size
- 8/ 6/32/64/ 28/256MB SDRAM DIMM
- 64 data bits structure only
• •
• •
• I/O Expansion Slot
- 3 x Master / Slave PCI slots (PCI 2.2 compliant)
- x AMR (Audio/Modem Riser) slot
• Award BIOS
- Supports PC99, Plug-and-Play
- Supports ACPI, APM, DMI, Green Feature
• •
• •
• I/O Functions
- Support PIO Mode 3,4 ATAPI devices and Ultra DMA/66
- Supports 2 high speed UART 6550 COM ports
- Supports SPP/EPP/ECP LPT port
- Supports 3 mode/ .44/2.88MB floppy drive
- Supports PS/2 Mouse and PS/2 Keyboard
- Supports IrDA port
- Supports 2 USB (Universal Serial Bus) ports
- Supports VGA port
INTRODUCTION 3

4 INTRODUCTION
- Supports Line-out, Line-in and MIC-in jack
- Supports Game/MIDI port
• Built-in AC97 CODEC
- AC97 2. compliant
- SB emulation and support 3D Wavetable synthesis
• Switching Voltage Regulator
- Intel VRM 8.4 compliant
• Other Features
- Year 2000 compliant
- Power failure resume
- FWH (Firmware Hub) supports security manageability
- BIOS Virus protection (warning)
- PS/2 Mouse and Keyboard Wake Up
- Support Wake-on-LAN function
- Remote Ring Wake Up
- Time Wake Up
- Board voltage monitors for CPU core, +3.3V, +/-5.0V,+/- 2.0V, VTT and VBAT
- CPU overheat alarm
- CPU fan auto-off in sleep mode
- VCORE & VIO Adjust
• PCB Di ensions
- Micro ATX form factor, 4-layer PCB, 20.7cm x 24.5cm (8. 5 x 9.6)

HARDWARE INSTALLATION 5
· 4M Bytes Display cache memory.
(TS-UWH3 ,TS-UWE3 only)
· Winbond 83627HF-AW
· Wake-on-LAN
· 4M bits FWH Flash Memory
(Intel 82802AB)
· 3x PCI Slots
· x AMR Slot
(Audio/Modem Riser)
Back panel I/O ports CPU Main Me ory
Intel 810 chipset
Expansion SlotsAC97 CODEC
LPC SuperI/O
Display Cache
IrDA Header
Syste BIOS
WOL Header
Switching Reg.
· SIR, CIR, ASKIR
PCI IDE Connector
· Bus Master
· PIO Mode 3/4
· DMA Mode 2
· Ultra DMA 33/66
FDD Connector
· Floppy Disk Drive Connector
· AC97 V2.
Audio CODEC
COMB Connector
· Serial COM port 2 connector
·Game/ MIDI port & Audio Jack
(Line-in, Line-out, MIC-in)
·VGA port & serial port &
parallel printer port
·2 x USB ports
·PS/2 KB & PS/2 Mouse ports
·Intel® Celeron/
PentiumIII FC-PGA
Series
·Intel VRM8.4 Compliant
·2 x 68-pin SDRAM DIMM
·Up to 5 2MB
· TS-UWL3 :Intel 8 0
· TS-UWH3 :Intel 8 0 DC- 00
· TS-UWE3 :Intel 8 0E
CHAPTER 2 HARDWARE INSTALLATION
2.1 Transcend TS-UWL31/TS-UWH31/TS-UWE31 Motherboard

6 HARDWARE INSTALLATION
2.2 Layout of Transcend TS-UWL31/TS-UWH31/TS-UWE31
Motherboard
DIMM1 (64bit 168pin SDRAM Module)
DIMM2 (64bit 168pin SDRAM Module)
PCI Slot1
(
PCI1
)
PCI Slot2
(
PCI2
)
PCI Slot3
(
PCI3
)
PS/2
T:Mouse
:Ke
y
board
US
T:Port 1
:Port 2
ATX Power Connector
KB MOUSE
USB
POWER-FAN
CPU-FAN
KB-AWK
WOL
Panel Connector
CASE-FAN
CMOS-CLR
IrDA
FDC
IDE2 IDE1
JP5
GMCH
COMB
JP2
FWH
JP
AC97
AMR
Game Port
Line_in
MIC
Intel
ICH
TS-UWH31
Winbond
83627
CD2 CD1 MODEM
Intel
COMA
VGA
Parallel Port
Li atter
y
VIDEO AUX
Line_out
/100/133MHz
Pin1
Transcend
JP20
JP15
JP22

2.3 CPU (Central Processing Unit) Installation
So far you have familiarized yourself with the handling precautions, checked you have all of
the necessary hardware for building your system, inspected the motherboard package contents
and looked at the layout of the motherboard. This chapter will take you step by step through
the process of installing the different hardware devices onto it.
Caution
1. Re e ber to always ake sure the syste power is off before installing or re oving
any devices.
2. Dont forget the static electricity precautions.
3. Be careful ! Inserting hardware onto your otherboard incorrectly can da age it.
The motherboard has a ZIF Socket 370 which houses the CPU. A fan is necessary for the
CPU to prevent overheating. If there is no fan on it, please purchase one before you turn on
your system.
WARNING! Be sure that sufficient air circulation is available across the processors
passive heatsink. Without sufficient circulation, the processor could overheat and
da age both the processor and the otherboard. You ay install an auxiliary fan, if
necessary.
Please follow the steps below to install the CPU:
Step :
To install the CPU, first turn off your system and remove its cover. Locate the ZIF socket and
open it by first pulling the lever sideways away from the socket then upwards to a 90-degree
right angle. Insert the CPU in the correct direction as shown below. The picture below is for
reference only. You should have a CPU fan to cover the face of the CPU. With the added
weight of the CPU fan, no force is required to insert the CPU. Once completely inserted, close
the sockets lever while holding down the CPU.
HARDWARE INSTALLATION 7

Step2:
Next, according to the CPU type you install, set JP 5 to short pin & pin2 for Intel ® CeleronTM
and Pentium ® III FC-PGA series CPU, or set JP 5 to short pin2 & pin3 for CYRIX Joshua
series CPU. Connect the CPUs fan cable to the CPU-FAN connector indicated on the diagram
below. Ensure that the cable is connected correctly! It will be obvious which way it fits.
8 HARDWARE INSTALLATION
DIMM1 (64bit 168pin SDRAM Module)
DIMM2 (64bit 168pin SDRAM Module)
PCI Slot1 (PCI1)
PCI Slot2 (PCI2)
PCI Slot3 (PCI3)
PS/2
T:Mouse:Keyboard
US
T:Port 1:Port 2
ATX Power Connector
KB MOUSE
USB
POWER-FAN
CPU-FAN
KB-AWK
WOL
Panel Connector
CASE-FAN
CMOS-CLR
IrDA
FDC
IDE2
IDE1
JP5
GMCH
COMB
JP2
FWH
JP
AC97
AMR
Game Port
Line_in
MIC
IntelICH
TS-UWH31
Winbond83627
CD2
CD1 MODEM
Intel
COMA
VGA
Parallel Port
Li attery
JP3
JP18
VIDEO AUX
Line_out
/
100MHz
Pin1
AUDIO
Transcend
Socket
370 CPU
(
Top View
)
Socket
370 CPU
(Bottom View)
Socket 370 CPU Installation
Notch
Notch
CPU_FAN
Notch
1
1INTEL
CYRIX
JP15

2.4 66/100/133MHz Syste Configuration
The (JP20) allows you to set the FSB (Front Side Bus) to either AUTO/66/ 00/ 33MHz
configurations. And through CPU Host/PCI Clock of Frequency/Voltage Control in the
BIOS Setup menu (please refer to page 47). When JP3 is set to 66MHz, you can select the
system bus frequency from 66MHz to 75MHz. When JP3 is set to 00MHz, you can select the
system bus frequency from 00MHz to 50MHz.
HARDWARE INSTALLATION 9
DIMM1 (64bit 168pin SDRAM Module)
DIMM2 (64bit 168pin SDRAM Module)
PCI Slot1 (PCI1)
PCI Slot2 (PCI2)
PCI Slot3 (PCI3)
PS/2
T:Mouse:Keyboard
US
T:Port 1:Port 2
ATX Power Connector
KB MOUSE
USB
POWER-FAN
CPU-FAN
KB-AWK
WOL
Panel Connector
CASE-FAN
CMOS-CLR
IrDA
FDC
IDE2
IDE1
JP5
GMCH
COMB
JP2
FWH
JP
AC97
AMR
Game Port
Line_in
MIC
IntelICH
TS-UWH31
Winbond83627
CD2
CD1 MODEM
Intel
COMA
VGA
Parallel Port
Li attery
VIDEO AUX
Line_out
/
100MHz
Pin1
Transcend
66/100/133MHz SB Configuration Jumper
66MHz
JP20
100MHz
1
1
1
1
1
133MHz
AUTO
Note:
UWL31-Support 66/100MHz
UWH31-Support 66/100MHz
UWE31-Support 66/100/133MHz

10 HARDWARE INSTALLATION
2.5 Me ory Configuration
This motherboard must be installed with PC 00 SDRAM DIMM, and can house either one or
two of these modules.
IMPORTANT: Me ory speed setup is reco ended through the functions in the
Advanced Chipset Features. (Please refer to page 35)
Install memory in any combination as follows:
68-pin DIMM
SDRAM 8, 6, 32, 64, 28 ,256MB
SDRAM 8, 6, 32, 64, 28, 256MB
5 2MB (MAX.)
DIMM Location
DIMM
DIMM2
Total Memory
168Pin Memory DIMM Sockets
DIMM1 (64bit 168pin SDRAM Module)
DIMM2 (64bit 168pin SDRAM Module)
PCI Slot1 (PCI1) PCI Slot3 (PCI3)
PS/2
T:Mouse:Keyboard
US
T:Port 1:Port 2
ATX Power Connector
KB MOUSE
USB
POWER-FAN
CPU-FAN
KB-AWK
WOL
Panel Connector
CASE-FAN
CMOS-CLR
IrDA
FDC
IDE2
IDE1
JP5
GMCH
JP2
FWH
JP
AC97
AMR
Game Port
Line_in
MIC
IntelICH
Winbond83627
CD2
CD1 MODEM
Intel
COMA
VGA
Parallel Port
Li attery
VIDEO AUX
Line_out
Pin1
AUDIO
Transcend
Unbuffered Position
3.3V Position
168-pin Unbuffered SDRAM Module (DIMM1)
168-pin Unbuffered SDRAM Module (DIMM2)

HARDWARE INSTALLATION 11
2.6 Keyboard Wake Up (3-pin KB-AWK)
This function makes the Keyboard Power Up the system. Set this jumper to Enable if you
would like your Keyboard to Power Up your computer. Then, go to the Integrated Peripherals
in the BIOS Setup Menu (please refer to page 37), and choose the setting you prefer.
Keyboard Wake Up
1
1
Disable
Enable
JP21
KB-AWK
DIMM1 (64bit 168pin SDRAM Module)
DIMM2 (64bit 168pin SDRAM Module)
PCI Slot1 (PCI1)
PCI Slot2 (PCI2)
PCI Slot3 (PCI3)
PS/2
T:Mouse:Keyboard
US
T:Port 1:Port 2
ATX Power Connector
KB MOUSE
USB
POWER-FAN
CPU-FAN
KB-AWK
WOL
Panel Connector
CASE-FAN
CMOS-CLR
FDC
IDE2
IDE1
JP5
GMCH
COMB
JP2
FWH
JP
AC97
AMR
Game Port
Line_in
MIC
IntelICH
TS-UWH31
Winbond83627
CD2
CD1 MODEM
Intel
COMA
VGA
Parallel Port
Li attery
VIDEO AUX
Line_out
/
100MHz
Pin1
Transcend

12 HARDWARE INSTALLATION
IDE Connectors
DIMM1 (64bit 168pin SDRAM Module)
DIMM2 (64bit 168pin SDRAM Module)
PCI Slot1 (PCI1)
PCI Slot2 (PCI2)
PCI Slot3 (PCI3)
PS/2
T:Mouse:Keyboard
US
T:Port 1:Port 2
ATX Power Connector
KB MOUSE
USB
POWER-FAN
CPU-FAN
KB-AWK
WOL
Panel Connector
CASE-FAN
CMOS-CLR
IrDA
FDC
IDE2
IDE1
JP5
GMCH
COMB
JP2
FWH
JP
AC97
AMR
Game Port
Line_in
MIC
IntelICH
TS-UWH31
Winbond83627
CD2
CD1 MODEM
Intel
COMA
VGA
Parallel Port
Li attery
VIDEO AUX
Line_out
/
100MHz
Pin1
Transcend
Primary IDE onnector
(Blue color)
Second IDE onnector
(Black olor)
IDE1
IDE2
PIN1
PIN1
IDE Connector
2.7 Pri ary / Secondary IDE Connectors (Two 40-1-pin IDE)
This motherboard supports two 40-pin IDE connectors marked as IDE (primary channel)
and IDE2 (secondary channel). Each channel supports two IDE devices, making a total of
four devices.
Connect your Hard Disk (the main one if you are using more than one) to the Master connector
(at the end of the cable) and connect it to the IDE (see important note below). If your HDD
supports Ultra DMA/66, you must use an 80-wire cable, otherwise the HDD wont be able to
reach this speed.
If you intend to operate two IDE devices from the same channel, one device must be set to
master mode, the other to slave mode. A Hard Disk, CD ROM or other IDE device can
have either setting, depending on devices jumper. Please refer to the devices manual for
more information.
NOTE:
The Connectors ust be attached to the IDE channels the right way round. Make
sure that the red stripe on one edge of the ribbon cable (this ay be faint and could
also be a dotted line) is the nearest to PIN 1 (on the left as the otherboard is shown
in the picture below).

HARDWARE INSTALLATION 13
loppy Disk Driver Connector
DIMM1 (64bit 168pin SDRAM Module)
DIMM2 (64bit 168pin SDRAM Module)
PCI Slot1 (PCI1)
PCI Slot2 (PCI2)
PCI Slot3 (PCI3)
PS/2
T:Mouse:Keyboard
US
T:Port 1:Port 2
ATX Power Connector
KB MOUSE
USB
POWER-FAN
CPU-FAN
KB-AWK
WOL
Panel Connector
CASE-FAN
CMOS-CLR
IrDA
FDC
IDE2
IDE1
JP5
GMCH
COMB
JP2
FWH
JP
AC97
AMR
Game Port
Line_in
MIC
IntelICH
TS-UWH31
Winbond83627
CD2
CD1 MODEM
Intel
COMA
VGA
Parallel Port
Li attery
VIDEO AUX
Line_out
/
100MHz
Pin1
Transcend
PIN1
FDD Connector
.,+
2.8 Floppy Disk Drive Connector (34-pin FDC)
This connector supports the floppy disk drive ribbon cable which is one of the items in your
motherboard package. After connecting the single end to the board, connect the two plugs at
the other end to the floppy drives. Remember, as in the last section, the red stripe on the
edge of the ribbon cable must be the nearest to PIN , otherwise your connection wont work.
This means it be on the left as the motherboard is shown below.

14 HARDWARE INSTALLATION
2.9 Fan Power Connectors
There are three fan power connectors on the motherboard: CPU-FAN, POWER-FAN, and
CASE-FAN. Each connector provides + 2V power. The cables can only be attached a certain
way: If you try to put them in the wrong way, they wont fit. These connectors support cooling
fans of 500 mA (6W) or less.
DIMM1 (64bit 168pin SDRAM Module)
DIMM2 (64bit 168pin SDRAM Module)
PCI Slot1 (PCI1)
PCI Slot2 (PCI2)
PCI Slot3 (PCI3)
PS/2
T:Mouse:Keyboard
US
T:Port 1:Port 2
ATX Power Connector
KB MOUSE
USB
POWER-FAN
CPU-FAN
KB-AWK
WOL
Panel Connector
CASE-FAN
CMOS-CLR
IrDA
FDC
IDE2
IDE1
JP5
GMCH
COMB
JP2
FWH
JP
AC97
AMR
Game Port
Line_in
MIC
IntelICH
TS-UWH31
Winbond83627
CD2
CD1 MODEM
Intel
COMA
VGA
Parallel Port
Li attery
VIDEO AUX
Line_out
/
100MHz
Pin1
Transcend
POWER-FAN
CPU-FAN
CASE-FAN
Fan Power Connectors
Rotation
+12V
GND
FAN

2.10 Wake-on-LAN Connector (3-pin WOL)
This connector connects to LAN cards with a Wake-on-LAN output. The system can be
Powered Up when a wakeup packet or signal is received from the LAN card.
NOTE:This function requires that the Wake-Up by PCI & WOL function in the Power
Manage ent Setup is set to Enabled and that your syste has an ATX power supply
with at least 720 A +5V standby power.
HARDWARE INSTALLATION 15
DIMM1 (64bit 168pin SDRAM Module)
DIMM2 (64bit 168pin SDRAM Module)
PCI Slot1 (PCI1)
PCI Slot2 (PCI2)
PCI Slot3 (PCI3)
PS/2
T:Mouse:Keyboard
US
T:Port 1:Port 2
ATX Power Connector
KB MOUSE
USB
POWER-FAN
CPU-FAN
KB-AWK
WOL
Panel Connector
CASE-FAN
CMOS-CLR
IrDA
FDC
IDE2
IDE1
JP5
GMCH
COMB
JP2
FWH
JP
AC97
AMR
Game Port
Line_in
MIC
IntelICH
TS-UWH31
Winbond83627
CD2
CD1 MODEM
Intel
COMA
VGA
Parallel Port
Li attery
VIDEO AUX
Line_out
/
100MHz
AUDIO
Transcend
Wake-on-LAN Connector
+5V Standby
ND
PME
WOL

2.11 IrDA-Co pliant Infrared Module Connector (10-pin IrDA)
The IrDA connector can be configured to support a wireless infrared module. With this module
and application software such as Laplink or Win95 Direct Cable Connection, users can transfer
files to or from laptops (notebooks), PDAs and printers. You must also configure the setting
through UART Mode Select in the Integrated Peripherals (please refer to page 39) to
select IrDA. Connect the Standard IR (SIR) device to the onboard SIR connector according
to the pin definitions. An optional Consumer Infrared (CIR) set connects to the CIR and SIR
connectors simultaneously for both wireless transmitting and remote control functions through
one external infrared module.
16 HARDWARE INSTALLATION
DIMM1 (64bit 168pin SDRAM Module)
DIMM2 (64bit 168pin SDRAM Module)
PCI Slot1 (PCI1)
PCI Slot2 (PCI2)
PCI Slot3 (PCI3)
PS/2
T:Mouse:Keyboard
US
T:Port 1:Port 2
ATX Power Connector
KB MOUSE
USB
POWER-FAN
CPU-FAN
KB-AWK
WOL
Panel Connector
CASE-FAN
CMOS-CLR
IrDA
FDC
IDE2
IDE1
JP5
GMCH
COMB
JP2
FWH
JP
AC97
AMR
Game Port
Line_in
MIC
IntelICH
TS-UWH31
Winbond83627
CD2
CD1 MODEM
Intel
COMA
VGA
Parallel Port
Li attery
VIDEO AUX
Line_out
/
100MHz
Pin1
AUDIO
Transcend
IrDA Connector
IrDA
+5V
IRRX
NC
ND
IRTX
NC
5VSB
CIRRX
NC
NC
12
910
CIRSIR