Transmitter Solutions Dolphin DOLXFD1000B-M User manual

DOLXFD1000B-M/S
Mullion or Single Gang Keypad
with Card Reader
-40°+140°
IP66
V.1.19.18
PH 866.975.0101
FX 866.975.0404
www.transmittersolutions.com

The DOLXFD1000BS/DOLXFD1000BM is a single door mulifunction stand alone
access controller or a Wiegand output reader. It uses Atmel MCU assuring stable
performance. The operation is very user-friendly, and low-power circuit makes a
long service life.
The DOLXFD1000BS/DOLXFD1000BM supports 1,000 users (998 common users
+ 2 panic users), all user data can be transferred from one to another. It supports
multi access modes in either card access, PIN access, Card + PIN access, or multi
cards/PINs access. It has extra features including block enrollment, interlocked,
Wiegand26~37 bits interface...etc.

DOLXFD1000BMDOLXFD1000BS

DOLXFD1000BS DOLXFD1000BM

Notes: the DOLXFD1000BS/DOLXFD1000BM has 3 working modes: Stand alo
Mode, Controller Mode, Wiegand Reader Mode, choose the mode you would like
to use. (Factory default is Stand alone Mode / Controller Mode.)
The DOLXFD1000BS/DOLXFD1000BM can be worked as Stand alone Reader for
a single door. (Factory default mode)--7 2 #

DOLXFD1000BS/DOLXFD1000BM

For Multi cards/PINs access mode, the interval time of reading cards/inputting PINs
can not exceed 5 seconds, or else, the DOLXFD1000BS/DOLXFD1000BM will exit
to standby automatically.

The DOLXFD1000BS/DOLXFD1000BM can be work as a Controller, connected
with the external Wiegand reader. (Factory default mode)--7 2 #

The DOLXFD1000BS/DOLXFD1000BM connected with External Card Reader:
- If EM card reader of HID card reader: users can be added/deleted on either the
DOLXFD1000BS/DOLXFD1000BM or external reader.
- If Mifare reader: users can only be added/deleted on external reader.
DOLXFD1000BS/DOLXFD1000BM

The DOLXFD1000BS/DOLXFD1000BM connected with Fingerprint Reader:
For example:
Connect F2 as the fingerprint reader to the DOLXFD1000BS/DOLXFD1000BM,
it is of two steps to enroll the valid fingerprint.
Step 1: Add the Fingerprint (A) on F2
Step 2: Add the same Fingerprint (A) on the DOLXFD1000BS/DOLXFD1000BM
The DOLXFD1000BS/DOLXFD1000BM connected with Keypad Reader:
The keypad reader can be 4 Bits, 8 Bits (ASCll), or 10 Bits output format.
Choose the below operation according to the PIN output format of your reader.
> Add PIN Users:
To add PIN users, after enter into programming mode on the DOLXFD1000BS/
DOLXFD1000BM, PIN(s) can be input/ added on either the DOLXFD1000BS/
DOLXFD1000BM controller or the external Keypad Reader.
To DOLXFD1000BS/DOLXFD1000BM can work as Stanard Wiegand Reader,
connected to the third party Controller--- 7 3 #
Notes:
The EM version reads EM cards only, while the HID & EM version can be set to
read HID & EM cards, or HID card only, or EM card only. Factory default card type
of the HID & EM version is HID & EM cards, if you want to change the type, please
se the DOLXFD1000BS/DOLXFD1000BM to Stand Alone Mode (7 2 #) and then set
the type. (See page 11 for setting card type.)

DOLXFD1000BS/DOLXFD1000BM

User Information Transfer:
The DOLXFD1000BS/DOLXFD1000BM supports the Use Information Transfer
function, and the enrolled user (cards, PINs) can be transferred from one (let’s name
it master unit) to another (let’s name it accept unit)
DOLXFD1000BS/DOLXFD1000BM DOLXFD1000BS/DOLXFD1000BM

Interlock:
The DOLXFD1000BS/DOLXFD1000BM supports the Interlock function. It is two
keypads for two doors, and mainly used for banks, prisons and other places where
a higher level secuirty is required.
DOLXFD1000BS/DOLXFD1000BM DOLXFD1000BS/DOLXFD1000BM

TRANSMITTER SOLUTIONS WARRANTY
The warranty period of Transmitter Solutions keypad is twenty-four (24) months.
This warranty shall begin on the date the keypad is manufactured. During the
warranty period, the product will be,repaired or replaced (at the sole discretion
of Transmitter Solutions) if the product does not operate correctly due to a
defective component. This warranty does not extend to (a) the keypad case,
which can be damaged by conditions outside the control of Transmitter Solu-
tions, or (b) battery life of the keypad. This warranty is further limited by the
following disclaimer of warranty and liability:
EXCEPT AS SET FORTH ABOVE, TRANSMITTER SOLUTIONS MAKES NO WARRANTIES
REGARDING THE GOODS, EXPRESS OR IMPLIED, INCLUDING WARRANTY OF
MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. BUYER
MAKES NO RELIANCE ON ANY REPRESENTATION OF TRANSMITTER SOLUTIONS,
EXPRESS OR IMPLIED, WITH REGARD TO THE GOODS AND ACCEPTS THEM
“AS-IS/WHERE-IS”. TRANSMITTER SOLUTIONS SELLS THE GOODS TO BUYER ON
CONDITION THAT TRANSMITTER SOLUTIONS WILL HAVE NO LIABILITY OF ANY KIND
AS A RESULT OF THE SALE. BUYER AGREES THAT TRANSMITTER SOLUTIONS SHALL
HAVE NO LIABILITY FOR DAMAGES OF ANY KIND, WHETHER DIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES, INCLUDING INJURIES TO PERSONS OR PROPERTY, TO
BUYER, ITS EMPLOYEES OR AGENTS, AS A RESULT OF THE SALE. BUYER ALSO
AGREES TO HOLD TRANSMITTER SOLUTIONS HARMLESS FROM ANY CLAIMS BUYER,
OR ANY THIRD PARTY, MAY HAVE AS A RESULT OF BUYER’S USE OR DISPOSAL OF
THE GOODS. BUYER HAS READ THIS DISCLAIMER AND AGREES WITH ITS
TERMS IN CONSIDERATION OF RECEIVING THE GOODS.

2480 South 3850 West, Suite B
Salt Lake City, UT 84120
[phone] • [phone] fax
www.transmittersolutions.com