Response Electronics SAKP E User manual

These instructions shou d be read in conjunction with
your System Insta ation and Operating Instructions
and be retained for future reference
.
Introduction
Th SAKP E Wir fr R mot K ypad is d sign d for us
with R spons Wir fr Intrud r Alarm syst ms op rating
on 433MHz only
.
Th Wir l ss K ypad is us d to control th syst m by using
a four digit Us r Acc ss Cod . Th K ypad incorporat s
Panic and anti-tamp r prot ction f atur s that will
imm diat ly initiat a Full Alarm condition wh n activat d.
Any att mpt to op n th casing of th K ypad will
imm diat ly initiat a Full Alarm condition v n if th
syst m is disarm d, (unl ss th syst m is in S rvic , T st or
Programming mod s). In addition if a s qu nc of mor
than 16 incorr ct k y pr ss s is nt r d th K ypad will b
disabl d for th n xt 1 minut . During this 1 minut duration
th LED will k p flashing slowly. Cons cutiv ly disabl d
for 3 tim s, th K ypad will mit th tamp r signal to th
Control Pan l.
Th K ypad’s Us r Acc ss Cod is ind p nd nt from any
acc ss cod s us d with a Control Pan l.
Th K ypad is pow r d by a 9V PP3 Alkalin batt ry. Und r
normal op rating conditions this will provid an xp ct d lif
in xc ss of 1 y ar. Wh n th batt ry l v l falls b low an
acc ptabl l v l, th “LOW BATTERY” indicator on th front
of th K ypad will flash. Wh n this occurs th batt ry should
b r plac d as soon as possibl .
Positioning the Keypad
Th K ypad is rat d IP44 and suitabl for mounting
outdoors. Th K ypad should b mount d in a position
clos to th main ntranc door so that th us r acc ss
cod can b nt r d asily.
Ensur that th position s l ct d for th K ypad is within
th ff ctiv rang of th Sir n or Control Pan l.
Note: DO NOT fix th K ypad to m talwork or locat th
unit within 1m of m talwork (i. . radiators, wat r pip s, tc)
as this could aff ct th radio rang of th K ypad.
Insta ing and Configuring
the Keypad
If you hav a syst m with a Control Pan l, nsur it is in
T st or Programming Mod . If you hav a syst m without a
Control Pan l, nsur that th Sir n is in S rvic mod .
1. Undo and r mov th fixing scr w from th bottom dg of
th K ypad and r mov th wall mounting plat . (Fig. 2).
2. Using th mounting plat as a t mplat , mark th
positions of th four fixing hol s on th wall.
Note: To mak th b st us of anti-tamp r prot ction
you must ins rt a wall plug and scr w in th sp cifi d
hol (as illustrat d).
3. Fix th mounting plat to th wall using th scr ws and
wall plugs provid d, (a 5mm hol will b r quir d for th
wall plugs). Do not ov r-tight n th fixing scr ws as this
may distort or damag th mounting plat .
Note: Installing th K ypad against a flat and smooth
wall is of gr at importanc so as to avoid th tamp r
switch b ing fals ly trigg r d.
Note: Th wall plugs suppli d with th product ar not
suitabl for plast rboard walls, if mounting th K ypad
on to plast rboard us appropriat wall plugs.
Anti-Tamper
Protection
Fixing
Screw
Fig. 2
Wall Mounting Plate
0
1 2 3
4 5 6
7 8 9 2
1
Arm
Disarm
Part-Arm 1
or Delay Arm
Part-Arm 2
or Delay Arm
Low Battery
Indicator
LED
Transmit
Indicator
LED
Key Pressed
Confirmation
Indicator LED
2
1
Fig. 1 Wireless Keypad Function Guide
433MHz Wirefree Remote Keypad (SAKP E)
Installation and Op rating Instructions

4. Undo and r mov th two fixing scr ws in th r ar of th
K ypad and r mov th r ar cov r. (Fig. 3).
5. Th r ar two jump r links locat d abov th batt ry
compartm nt. (Fig. 3)
J2 jumper link: Reset to Factory default
J3 jumper link: System type selection
If th K ypad is to b us d with a Sir n Controll d Syst m
th n th jump r link J3 must b s t as shown on Fig. 4a. If
your syst m has a s parat Control Pan l th jump r link J2
must b s t as shown on Fig. 4b.
To v rify th compatibility of your syst m follow th st p
b low for t sting:
Pr ss and tog th r for mor than 2 s conds.
Th K ypad will s nd th Panic signal to th Control pan l,
if th Control pan l do s not r act prop rly, adjust th
jump r link J3 accordingly.
6. Conn ct th PP3 Alkalin batt ry to th batt ry clip.
7. R plac th r ar cov r and r fit fixing scr ws. Do not
ov r-tight n th fixing scr ws.
8. R fit th K ypad by slanting 45° onto th wall mounting
plat . Do not ov r-tight n th fixing scr w. (Fig. 5).
Note: Th K ypad is suppli d with a d fault Us r Acc ss
Cod of: 1234. For s curity r asons, it is r comm nd d
that this cod is chang d to anoth r four digit numb r
which only you and oth r us rs of th syst m know.
Note: Us thumb and middl fing r to hing off th K ypad
cov r. (Fig. 6) Th K ypad has a back light illumination
facility. It will illuminat for 5 s conds wh n op ning th
K ypad cov r or pr ssing any k y.
Testing the Keypad
Ensur that th Control Pan l is in T st or Programming Mod .
1. Pr ss
to arm th syst m
2. Pr ss and hold and buttons tog th r, aft r
approximat ly 2 s conds, an alarm will b initiat d
3. Pr ss
to disarm th syst m
Operating the Keypad
Arm:
Pr ss
Part-Arm: (for Contro Pane Systems)
Pr ss
for Part-Arm 1
Pr ss
for Part-Arm 2
De ay-Mode: (For siren on y systems)
To Arm th syst m in D lay Mod nt r th Us r Acc ss Cod
follow d by either of th ‘DELAYARM’ buttons on th K ypad.
Th Sir n will acknowl dg th signal by b ping onc and
th n again aft r th 15 s cond ntry d lay.
Fig. 5
Fig. 6
,
User Access Code
? ? ? ?
,
User Access Code
? ? ? ?
,
User Access Code
? ? ? ? 1
,
User Access Code
? ? ? ? 2
, or
User Access Code
? ? ? ? 1 2
,
User Access Code
? ? ? ?
1
2
1
2
System Type
Jumper
Link J3
Reset
Jumper
Link J2
Anti-Tamper
Switch
Fig. 3
1
1 J3 J3
Fig. 4a Fig. 4b

Disarm:
Pr ss
Panic:
Default setting: On
Pr ss and hold and buttons tog th r for
mor than 2 s conds with LED flashing rapidly.
To nabl or disabl th panic function, follow th b low
st ps in s qu nc :
Disab ing the Panic:
1. Pr ss
2. Ent r
3. Pr ss , th LED will illuminat onc
and flash twic
4. Pr ss
5. Pr ss , th LED will illuminat onc
and flash thr tim s to confirm th s tting has
b n acc pt d.
Enab ing the Panic:
1. Pr ss
2. Ent r
3. Pr ss , th LED will illuminat onc
and flash twic
4. Pr ss
5. Pr ss , th LED will illuminat onc
and flash thr tim s to confirm th s tting has
b n acc pt d.
Inputting the House Code
In ord r to pr v nt any unauthoris d att mpt to op rat or
disarm your syst m, you must configur your syst m to
acc pt radio signals only from your own syst m d vic s. This
is don by s tting a s ri s of ight miniatur (DIP) switch s in
all d vic s to th sam ON/OFF combination (Th Hous
Cod ) s l ct d by th us r/install r. Th K ypad is d sign d
to b affix d outdoor. For s curity r asons, it do s not includ
a DIP switch, but hous cod s tting is ss ntial.
To input th hous cod , pr ss th following k ys in
s qu nc :
1. Pr ss
2. Ent r
3. Pr ss , th LED will illuminat onc
and flash twic
4. Pr ss
5. Pr ss , th LED will illuminat onc
and flash thr tim s to confirm th s tting has
b n acc pt d.
For xampl : if th hous cod s t on th Control Pan l
r ads as: 12578. It m ans th Dip Switch numb rs 1, 2, 5,
7, 8 ar s t to th “ON” position, whil 3, 4, 6 ar s t to
th “OFF” position. Apply th Dip Switchs s t in “ON”
positions for hous cod inputting.
Resetting to Factory Defau t
If you forg t th Us r Acc ss cod , you can r s t th Us r
Acc ss cod to factory d fault by following th st ps b low:
1. R mov th batt ry.
2. Pr ss and hold any k y for mor than 1 s cond.
3. S t th Jump r link J2 as shown on Fig. 7b.
4. R fit th batt ry and t st it by pr ssing th d fault
Us r Acc ss cod of 1 2 3 4.
5. If th t sting is ok, s t th jump r link J2 as shown on
Fig. 7a, which is what th K ypad is s t to normally.
Changing the User Access Code
Default Code: 1 2 3 4
Wh n using th K ypad th k ys must b pr ss d firmly
and within fiv s conds of ach oth r. If you mak a
mistak , wait fiv s conds and r comm nc programming
from th b ginning of th s qu nc . To chang th Us r
Acc ss Cod , pr ss th following k ys in s qu nc :
1. Pr ss
2. Ent r
3. Pr ss , th LED will illuminat onc
and flash twic
4. Ent r
5. Pr ss , th LED will illuminat onc and
flash thr tim s to confirm th s tting has b n acc pt d.
,
User Access Code
? ? ? ?
User Access Code
? ? ? ?
1
2
2
2
User Access Code
? ? ? ?
House Code set on Control Panel
? ? ? ?
2
1
User Access Code
? ? ? ?
2
2
2
1
1
1 J2 J2
Fig. 7a Fig. 7b
User Access Code
? ? ? ?
1
1
New User Access Code
? ? ? ?
1

If th light do s not flash, wait fiv s conds and r -
nt r th programming s qu nc from th b ginning.
Disab ing the Keypad
If a s qu nc of mor than 16 incorr ct k y pr ss s is
nt r d th K ypad will b disabl d for th n xt 1 minut .
Cons cutiv ly disabl d for 3 tim s, th K ypad will mit a Tamp r
signal to th control pan l with LED flashing slowly.
Note: Wh n th K ypad is disabl d for 1 minut , th
LED will flash slowly, indicating that th K ypad is
shut down t mporarily. During this 1 minut , any pr ssing
to th K ypad will b tr at d as invalid pr ssing. Aft r th
laps of 1 minut , ff ctiv inputting will b acc pt d.
Rep acing the Batteries
Th “LOW BATTERY” indicator on th front of th K ypad
will not flash until th K ypad mits RF radio signal. In
short, th “LOW BATTERY” indication won’t b s n in
normal circumstanc . Th batt ri s should b r plac d as
soon as possibl as follows:
1. By pr ssing th Us r Acc ss cod twic , two LEDs
( & ) will k p flashing for 20 s conds. During
this 20 s conds duration, no radio signal will mit and
any inputting will not b acc pt d. In this way, th K ypad
won’t mit radio signal wh n r placing th batt ry.
2. Undo fixing scr w at bottom of K ypad and r mov
from wall mounting plat .
3. Undo two fixing scr ws in th r ar cov r and r mov
cov r.
4. R plac batt ry with a n w 9V PP3 Alkalin batt ry.
5. R plac and fix th r ar cov r and th n r fit and s cur
th K ypad onto th wall plat .
So ar Siren Operating Mode:
Solar Siren ON
To switch th Solar Sir n into Op rating Mod :
Pr ss (and hold)
for approx 10 s conds until th sir n mits a singl long
b p and long flash.
Solar Siren OFF
To switch th Solar Sir n into Op rating Mod :
Pr ss (and hold)
for approx 10 s conds until th sir n mits a singl long
b p and long flash.
Th Disarm k y should b r l as d aft r th long b p.
Anti-tamper Protection
Th K ypad incorporat s anti-tamp r prot ction f atur s
against unauthoris d att mpts to r mov th K ypad from
th wall. If it has b n r mov d from th wall, a full alarm
condition will b initiat d.
Troub eshooting
Disposa and Recyc ing
Disposal of this product is cov r d by th
Wast El ctrical or El ctronic Equipm nt
(WEEE) Dir ctiv .
It should not b dispos d of with oth r
hous hold or comm rcial wast .
At th nd of its us ful lif th packaging and product
should b dispos d of via a suitabl r cycling c ntr .
Pl as contact your local authority or th r tail r from
wh r th product was purchas d for information on
availabl faciliti s.
Response E ectronics Ltd.
Roman Hous , Lysons Av nu , Ash Val , Surr y GU12 5QF
Email: [e-mail]
W b: www.ResponseElectronics.com
Customer Support He p ine: 0845 373 1353
(Local Call Rat - lin s op n 09.00 to 17.00 Monday to Friday)
SAKP E Ed.3
Guarantee
Th product is guarant d for on y ar from th dat of purchas
against faulty mat rials and workmanship. No liability can b acc pt d
for any probl ms caus d by fair w ar and t ar, buy r’s n glig nc ,
improp r fitting or us , wilful or accid ntal damag , or any
cons qu ntial loss or damag howso v r caus d. This guarant
do s not aff ct your statutory rights and is valid for UK and EIRE only.
If you b li v th product to b faulty or in th unlik ly v nt of th
product d v loping a fault during th warranty p riod, th n pl as
contact our Custom r Support T am (contact d tails shown b low)
for product assistanc . Product r pair or r plac m nt will b off r d
for faulty products only with our prior agr m nt. Should you n d
to r turn a products th n:
1. Contact th H lp Lin on th numb r b low to obtain a R turn
Authorisation Numb r.
2. Ad quat ly packag your product to pr v nt damag in transit
and includ th following:
a. A copy of your original invoic /r c ipt.
b. A cov ring l tt r giving your full contact d tails, including
mail addr ss (if applicabl ).
c. A d scription of th fault or probl m.
Status Possible Cause Remedy
No function 1. Batt ry too w ak R plac with a
nw batt ry
2. Wrong coding Ch ck if both
HOUSE CODES
ar xactly th sam
LED flash Batt ry too w ak R plac with a n w
batt ry
,
? ? ? ?
,
? ? ? ?