TRAXION Topside Creeper Shorty User manual

engineered products
Topside Creeper
Shorty
Thank you for purchasing this Topside Creeper Shorty.
If you have any questions or comments please
visit our website at www.traxionproducts.com
or phone [phone].
© 2019 All Rights Reseed
Part No. 3-104

TopSide Creeper
Shorty Parts List
I-Beam x1
Front Beam x1
Back Beam x1
Ladder Housing x1
Ladder x1
Required Tools:
13mm Wrench
17mm Wrench
F
13mm Nut x?
Short 13mm Bolt x?
Long 13mm Bolt x4
Medium 13mm Bolt x?
Lock Pin x1

K L 0
17mm Nutx2
p
17mm Boltx2
Caster x1 Locking Caster x1
Pouch x1
Pouch Bar x1
Pad Housing x1
Foam Tube x3
6mm Phillips Screw x?
Pad x1 6mm Nut x2

0 Assemble Base
VERY IMORTANT
Before assembly please check to make sure all parts
are present. If something is missing, please contact
our oce on the phone at 479-474-3460 or over
email at servi[email protected]
First, take the front bar (B) and insert
it into the side of the I-beam (A) with
the yellow sticker.
The caster sockets
should face towards
the rest of the I-bea m as shown by
the red circles.
(H x2)
Next, take the back bar (C)
and insert it into the other
side of the I-beam (A). The
caster sockets should face
away from the front beam
as shown by the red circles.
(H x2)
\
\
Next, attach the I-beam and front bar
using 2x long 13mm bolts (H) and 2x
13mm nuts (F). Make sure to tighten the
bolts enough so that the front bar has no
wiggle room.
Finally, secure the back bar using 2x
long 13mm bolts (H) and 2x 13mm
nuts (F). Make sure to tighten the
bolte enough so that the back bar
has no wiggle room.

Attach Casters





(K)




 

Attach Ladder Housing
Hold the ladder housing (D) on top of the
assembled base so that the housing is on
the inside of the front beam's sockets.
Rest the bottom of the ladder housing
near the front beam with one hand and
with the other, extend and line up the
support beam and the hole on the i-beam
and insert the lock pin (J) as shown.
Secure the ladder housing with 2x 17mm
bolts (P) and 2x 17mm nuts (0), one of
each for each side, as shown in the
image below. Be sure that these bolts
are tight but make sure that the housing
can still move without diculty for
storage purposes.

8 Attach Ladder
Slide the ladder (E) through the ladder
housing, make sure htat the side with the
open ends is facing upwards, as idnicated
by the red circles .
To secure the ladder, move it to your de
sired height and insert the housing's
springbar fasteners into the hole and
move the ladder to the nearest setting,
when the springbars are in place the
ladder should not be able to slide into
dierent sockets. This process can be seen
in the images below.

Attach Pad Housing




 

Attach Pouch







0 Attach Pad Housing
Place the pad (N) on top of the pad houisng (M) and be sure that the
screw holes line up underneath. Use 2x phillips screws (T) to x the
pad in place, one one each side. To make this process easier, put the
screws in loosely and then tighten them once everything is in place.
(N)
 Attach Foam Tubes
Finally, attach the three foam tubes (S) to the ladder housing as
shown in the image below. The tubes have slits that allow you to slide
them onto the housing, you may have to apply a bit of force to get
the slits to open wide enough.