Trend Micro Cloud Edge 100 G2 User manual

TREND MICROTM
Cloud Edge 100 G2 Routing Mode/Bridge Mode
Trend Micro Cloud Edge is a next generation security solution for MSPs (Managed
Service Provider) that combines on-premises and cloud-based security features. Deploy
your Cloud Edge gateways on-premises and the MSP can remotely manage your
network through the cloud.
Deployment Modes
3
Opening and Inspecting the Carton
1
Verify that the Cloud Edge gateway carton contains the following items:
Deployment Checklist
4
1. Toggle the switch on the back panel as needed.
2. Connect the Cloud Edge gateway to a power source.
3. Power on the Cloud Edge gateway.
Setting up the Hardware
5
Power
Bridge Routing
Reset
1. Connect the WAN port to a wide area network (i.e. Internet).
2. Connect the LAN1 port to an internal endpoint (Bridge Mode) or an internal
network (Routing Mode).
Connecting to the Network
6
Requirement Details
Connect a laptop to the MGMT port. Connect the WAN port, which
serves as an uplink to the Internet, to the upstream side of the
network.
Bridge Mode:
 Connect the LAN1 port to an internal endpoint.
Routing Mode:
 Connect the LAN1 port to an internal network.
Bridge Mode:
 Obtain information for one internal address (sw0), either DHCP or
static (IP address, netmask, and gateway).
Routing Mode:
 Obtain the information about connecting to the WAN from your
Internet Service Provider (ISP): DHCP, Static, or PPPoE.
 Obtain IP address information for the LAN1 connection (Static).
Bridge Mode:
 Your network DNS server IP addresses.
Routing Mode:
 Use either automatic DNS settings assigned by the ISP’s DHCP or
obtain your network DNS server IP addresses.
A computer that has the following software installed:
 Adobe™Flash™10 or later
 Supported web browser
Firefox™61 or later
Google™Chrome 68 or later
Internet Explorer™10-11
Ethernet cables (3 cables)
IP addresses (1-2
addresses)
DNS settings
Laptop with Ethernet port
Mode Description
The Cloud Edge gateway acts as a transparent layer 2 device, providing scan and threat
protection without interrupting traffic flow. In addition, the gateway functions as a
hardware switch with a WAN port that provides the uplink to the Internet and seven LAN
ports that can be connected directly to endpoints such as clients, servers, and Wi-Fi
access routers.
The Cloud Edge gateway is visible on the network and acts as a layer 3 routing device
with traffic scanning and control capabilities.
Bridge
Routing
AC Adapter
Endpoint
100 - 240V AC
InternetModem/Router
Bridge Mode
Router
Internet
WAN
LAN1 LAN2 LAN3 LAN7
...
Cloud EdgeCloud Edge
......
Bridge Mode
LAN
...
Switch
Cloud Edge
Cloud Edge
Routing Mode
WLAN
Cloud Edge 100 G2
WANMGMT
Reset
CloudConsole
Connected
LAN8 LAN7 LAN6 LAN5 LAN4 LAN3 LAN2 LAN1
WAN
Cloud Edge 100 G2
WANMGMT
Reset
CloudConsole
Connected
LAN8 LAN7 LAN6 LAN5 LAN4 LAN3 LAN2 LAN1
Internet
Internet
Management
Laptop
AC Adapter
100 - 240V AC
Internet
Routing Mode
Management
Laptop
Internal
Switch
Power Cord
Opening and Inspecting the Carton
1
Documents
AC adapter
Cloud Edge Gateway
Serial cable
Verify that the Cloud Edge gateway carton contains the following items:
Ethernet cables (2)
Examining the Cloud Edge Gateway
2
Cloud Edge Gateway Front Panel
Cloud Edge Gateway Back Panel

Green LED Status
The Cloud Edge gateway cannot communicate with the Internet.
No light
The Cloud Edge gateway is not registered or cannot communicate
with Cloud Edge Cloud Console. Contact your managed service
provider for assistance.
Blinking green light
The Cloud Edge gateway is registered and communicating with
Cloud Edge Cloud Console.
Solid green light
Website:
http://www.trendmicro.com
List of worldwide offices and phone numbers:
http://www.trendmicro.com/us/about-us/contact/index.html
Contact Information
12
© 2019 Trend Micro Incorporated. All Right Reserved. Trend Micro and the t-ball logo are
trademarks or registered trademarks of Trend Micro Incorporated. All other company and/or product
names may be trademarks or registered trademarks of their owners. Information contained in this
document is subject to change without notice.
Item Code: APEQ18686/190627
The Green LED (Light-Emitting Diode) on the front panel shows the deployment status.
Verifying Connectivity
9
Green LED
TREND MICROTM
Cloud Edge 100 G2 Routing Mode/Bridge Mode
2. Specify DNS server IP addresses (if not assigned by DHCP).
3. Under System settings section:
a. Specify a FQDN in the Host name field.
b. Configure time settings.
 Automatically: Select Enable NTP server and enter the NTP server IP address.
 Manually: Select Manually set time and enter time in the Local time field.
4. Click Start Configuration Test to verify and then click Save & Register.
Routing Mode
1. In the Uplink configuration section, specify information for the WAN interface.
 DHCP
 PPPoE: Specify user name and password.
 Static: Specify IPv4 address, netmask, and gateway.
2. Specify DNS server IP addresses (if not assigned by DHCP or PPPoE).
3. Under System settings section:
a. Specify a FQDN in the Host name field.
b. Configure time settings.
 Automatically: Select Enable NTP server and enter the NTP server IP address.
 Manually: Select Manually set time and enter time in the Local time field.
4. Click Start Configuration Test to verify and then click Save & Register.
5. Click on the Cloud Edge On-Premises Console link.
6. Go to Network Interfaces.
7. Click the LAN1 interface, select L3 type, and configure IP address settings.
 DHCP
 Static: Specify IPv4 address, netmask, and optionally, a gateway.
8. Click Apply.
After logging on for the first time, the Quick Setup screen opens automatically.
Bridge Mode
1. In the Uplink configuration section, specify information for sw0.
 DHCP
 Static: Specify IPv4 address, netmask, and gateway.
Performing the Initial Configuration
8
Note:You can modify the Intranet Security mode after initial deployment using
Cloud Edge Cloud Console. You cannot modify which interfaces are
included in the switch.
Logging on the Web Console
1. Connect computer to the Cloud Edge gateway MGMT port.
2. Open a supported web browser.
3. Go to the following URL: https://192.168.252.1:8443/
4. Specify the logon credentials.
 User name: admin
 Password: adminCloudEdge
5. Press Enter or click Log On.
7
Client
Restoring Factory Settings
1. Power off the Cloud Edge gateway.
2. Press and hold the reset button located on the back panel.
3. Power back on the Cloud Edge gateway.
4. Release the reset button when the yellow LED starts to blink. The yellow LED
blinks for 2 minutes and then the gateway restarts.
Restore the Cloud Edge gateway to factory settings to reconfigure your network
settings or to decommission hardware. The yellow LED (Light-Emitting Diode) on
the back panel shows the factory settings restore status.
10
Yellow LED
Cautions
1. Lithium Battery Caution
 There is risk of explosion if the battery is replaced by an incorrect type.
 Dispose of used batteries according to the instructions.
 Installation should be performed only by a skilled person who knows all
installation and device specifications which are to be applied.
 Do not carry by the handle of power supplies when moving to another place.
 Please conform to your local laws and regulations regarding safe disposal of
lithium BATTERY.
 Disposal of a battery into a fire or a hot oven, or mechanically crushing or
cutting of a battery can result in an explosion.
 Leaving a battery in an extremely high temperature surrounding environment
can result in an explosion or the leakage of flammable liquid or gas.
 A battery subjected to extremely low air pressure may result in an explosion or
the leakage of flammable liquid or gas.
2. Grounding Caution
This equipment must be grounded and the power cord for product should be
connected to a socket outlet with a grounded connection.
11