TRENDnet TI-PF11SFP (V1) User manual

TI-PF11SFP (V1)
Quick Installation Guide

Table of Content
1 English
1. Before You Start
2. Quick Reference
3. Hardware Installation
4. Additional information

ENGLISHFRANÇAISDEUTSCH
ESPAÑOLРORTUGUÊS
1
1. Before You Start
Package Contents
ŸTI-PF11SFP
Ÿ Quick Installation Guide
ŸRemovable terminal block
ŸDIN-rail mount
ŸWall mount plates
Minimum Requirements
ŸExisting network
ŸPower supply (TI-S12048)
2. Quick Reference
SFP Module SFP Module
PoE Camera
TI-PG541
TI-PF11SFP
POE

ŸThe TI-PF11SFP can be placed on a desktop, wall, or mounted to a DIN-rail.
2. Position the unit in front of the DIN-rail and hook the mount over the top of the rail.
3. Hardware Installation
DIN-rail Mounting Instructions
1. Attach the DIN-rail mount bracket to the media converter.
3. Rotate the media converter downward towards the rail to lock it into place. You will know it
is secure when you hear the click.
4. To remove the unit, pull down to clear the bottom of the DIN-rail and rotate away from the
rail.
2
Mounting the unit Releasing the unit

ENGLISHFRANÇAISDEUTSCH
ESPAÑOLРORTUGUÊS
3
Wall Mounting Instructions
1. Attach the wall mount plates to the media converter.
2. Mount the unit.
Safety Note
ŸTurn off the power before connecting any module or wire. The correct power supply voltage
(48-56V DC) is listed on the product label. Check the voltage of your power source to make
sure that you are using the correct part. Do NOT use voltage greater than 48-56V DC, as
specified on the product label.
ŸCalculate the maximum possible current in each power wire and common wire. Observe all
electrical codes dictating the maximum current allowable for each wire size. If the current
surpasses the maximum ratings, the wiring could overheat, causing serious damage to your
equipment.
!

4
Applying Power
1. Connect the power supply (sold separately) to the included terminal block (as shown below)
and secure the screws.
Note: Polarities must match.
2. Attach the terminal block to the unit, connect the neutral wire to the ground, and supply
power to the power adapter.
3. Connect your Ethernet cable, install an SFP module, and connect a fiber cable to the media
converter. Check the LEDs to confirm the connections are established. Your installation is
completed.

ENGLISHFRANÇAISDEUTSCH
ESPAÑOLРORTUGUÊS
5
4. Additional information
2 DIP Switches
N/A
N/A
Reserved
100 Mbps
1000 Mbps
SFP Speed
1
2
OFFON

Manufacturer’s Name and Address
Person responsible for this declaration.
Signature:
Date: April 05, 2017
Title: Director of Technology
Name: Sonny Su
TRENDnet, Inc.
20675 Manhattan Place
Torrance, CA 90501 USA
Zwolsestraat 156 2587 WB
The Hague The Netherlands
Place of Issue: Torrance, California, USA
Directives:
Low Voltage Directive 2006/95/EC
EMC Directive 2004/108/EC
RoHS Directive 2011/65/EU
REACH Regulation (EC) No. 1907/2006
TRENDnet hereby declare that the product is in compliance with the essential requirements and
other relevant provisions under our sole responsibility.
This product is herewith confirmed to comply with the Directives.
Product Information:
Product Name:
Model Number: TI-PF11SFP
Trade Name: TRENDnet
Industrial SFP to Gigabit PoE+ Media Converter
Safety EN 60950-1: 2006 + A11: 2009 + A1: 2010 + A12: 2011 + A2: 2013
EMC EN 55011: 2009 + A1: 2010 Class A
EN 55022: 2010 + AC: 2011 Class A
EN 61000-6-4: 2007 + A1: 2011
EN 55024: 2010
EN 61000-6-2: 2005 + AC: 2005

Certifications
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received.
Including interference that may cause undesired operation.
TRENDnet
20675 Manhattan Place
Torrance, CA 90501
USA
Applies to PoE Products Only: This product is to be connected
only to PoE networks without routing to the outside plant.
Note
The Manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this
equipment. Such modifications could void the user’s authority
to operate the equipment.
Advertencia
En todos nuestros equipos se mencionan claramente las
caracteristicas del adaptador de alimentacón necesario para
su funcionamiento. El uso de un adaptador distinto al
mencionado puede producir daños fisicos y/o daños al equipo
conectado. El adaptador de alimentación debe operar con
voltaje y frecuencia de la energia electrica domiciliaria exitente
en el pais o zona de instalación.
Product Warranty Registration
Please take a moment to register your
product online. Go to TRENDnet’s website at:
www.trendnet.com/register
Technical Support
If you have any questions regarding the product
installation, please contact our Technical Support.
Toll free US/Canada: 1-866-845-3673
Regional phone numbers available
at www.trendnet.com/support
Waste electrical an electronic products must not
be disposed of with household waste. Please
recycle where facilities exist. Check with your
Local Authority or Retailer for recycling advice.
Copyright © 2017. All Rights Reserved. TRENDnet. TI-PF11SFP (V1) /04.05.2017