TRENDnet TV-NVR104 User manual

Quick Installation Guide
TV-NVR104 / TV-IP104D2 (V1.1)

Table of Content
1 English
1. Before you start
2. Hardware Drive Installation (For TV-NVR104 only)
3. System Installation
4. Initial Setup
5. Setup Wizard

1
Package Contents
Minimum System Requirements
1. Before You Start
ŸTV-NVR104 or TV-NVR104D2
ŸCD-ROM (Utility & User's Guide)
ŸPower Adapter
ŸNetwork cables (1.8 m / 6 ft.)
ŸOptical Mouse
ŸQuick Installation Guide
ŸMonitor/TV with VGA or HDMI connection
ŸHard drive (for TV-NVR104)

2
Skip this step if you have TV-NVR104D2.
2. Hardware Drive Installation (For TV-NVR104 only)
Note:
ŸStatic electricity can damage the TV-NVR104. Before handling the unit, discharge any static electricity by touching a metal object, or use
an anti-static wrist strap.
ŸThe TV-NVR104 supports 3.5” SATA hard drive up to 6TB.
1. Remove the four retaining screws from the bottom panel of the TV-NVR104.
2. The top cover is slotted vertically. From the back of the unit, gently slide the cover up to separate it from the lower panel.
3. Attach the SATA cable to the hard drive (not included) and control board. SATA connectors are keyed to prevent improper installation.

3
5. Reattach the top cover to the unit. Make sure the lower panel lines up with the slots on the cover.
4. Mount the hard drive to the TV-NVR104's drive bay using the mounting screws included with your hard drive.
6. Hard drive is now installed!

3. System Installation
Power
Display
VGA HDMI
WPS
4

5
4. Initial Setup
1. When you turn on your NVR you will be promoted to active the NVR. Please change the password to the requirements listed on the
window and click “ ”.OK
2. You will get a pop up that your device has been activated Please click “OK”.
Activation
Enter new password. For your security new password
must be between 8 and 16 characters and contain at
least one: Special character (!.@.#.$) Alphanumeric (1,
2,3, etc.) Upper case character.
OK Cancel
Username
New Password
Confirm Passw...
admin
OK
Attention
The device is activated.
i
3. After you setup your pattern, you will then be asked to setup your language select the language and click “Apply”.
English
Language
System Language
Apply Exit

6
5. Setup Wizard
1. First window will be if you want to start the wizard when the device starts. Please select the check box to your preference and click
“Next”.
2. Configure your time zone along with system date, time, and format then and click “Next”.
**Our password recovery system utilizes the device time and date so it is important to set it up correctly**
Wizard
Start wizard when device starts?
ExitNext
Wizard
(GMT-08:00) Pacific Time (U.S. & Canada)
Time Zone
Date Format MM-DD-YYYY
System Date 02-27-2017
System Time 10:20:55
Exit
NextPrevious
3. Next window is your network configuration. If you don't intend to have your NVR connected to a network you can click “Next”;
otherwise please configure your network settings then hit “Next”. It is recommended to enable both the DHCP Client and DNS DHCP.
Enable DNS DHCP
Primary DNS Server
Secondary DNS Server
10M/100M Auto detection
192 .168 .10 .60
255 .255 .255 .0
Network Type
Enable DHCP Client
IPv4 Address
IPv4 Subnet Mask
IPv4 Default Gateway . . .
Wizard
Exit
NextPrevious

7
4. Next window is your ports and DNS settings. If you don't have or don't know what DNS settings are, you can click “Next” otherwise
please configure your DNS settings then hit “Next”.
8000
Server Port
HTTP Port
RTSP Port
80
554
Wizard
Server Address
Device Domain Name
Status
Username
DDNS is disabled
Password
dyn.com
DDNS Type
Enable DDNS
Enable UPnP
Exit
NextPrevious
5. If this is your first setup on a new unit you may simply press “OK”. If you have installed a different Hard Drive, please select your Hard
Drive from the list and then click “Init” to initialize/format your hard drive. Once the Hard Drive is done initializing, click “OK”.
6. The final window contains the recording setup options. Please configure the NVR to your recording preferences: either Continuous or
Motion Detection. After that click “OK” and you're done!
Continuous
Motion Detection
Wizard
Exit
OK
Previous
Wizard
Label
1
Capacity
931.51GB
Status Property Type Free Space
Normal R/W Local 927GB
Previous
Exit
Init
OK
7. Installation is completed, please refer to user's guide for more detail information and other configurations. (or use our standard style from
other models)

Directives:
TRENDnet hereby declare that the product is in compliance with the essential requirements and
other relevant provisions under our sole responsibility.
This product is herewith confirmed to comply with the Directives.
Product Information:
Model Number:
Trade Name: TRENDnet
Safety EN 60950-1: 2006 + A11: 2009: +A1: 2010 + A12: 2011 + A2: 2013
EMC
Manufacturer’s Name and Address
Date: March 06, 2017
Title: Director of Technology
Person responsible for this declaration.
Place of Issue: Torrance, California, USA
Name: Sonny Su
Signature:
TRENDnet, Inc.
20675 Manhattan Place
Torrance, CA 90501 USA
Zwolsestraat 156 2587 WB
The Hague The Netherlands
LVD Directive 2014/35/EU
EMC Directive 2014/30/EU
RoHS Directive 2011/65/EU
WEEE Directive 2012/19/EU
REACH Regulation (EC) No. 1907/2006
EN 55022: 2010 Class B
EN 50130-4: 2011
EN 61000-3-2: 2006 + A1: 2009 + A2: 2009
EN 61000-3-3: 2008
TV-NVR104 / TV-NVR104D2
NVR

Copyright © 2017. All Rights Reserved. TRENDnet.
Waste electrical an electronic products must not be disposed of with
household waste. Please recycle where facilities exist. Check with your
Local Authority or Retailer for recycling advice.
Note
The Manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the
user’s authority to operate the equipment.
Advertencia
En todos nuestros equipos se mencionan claramente las caracteristicas del
adaptador de alimentacón necesario para su funcionamiento. El uso de un
adaptador distinto al mencionado puede producir daños fisicos y/o daños al equipo
conectado. El adaptador de alimentación debe operar con voltaje y frecuencia de la
energia electrica domiciliaria exitente en el pais o zona de instalación.
Certifications
This device can be expected to comply with Part 15 of the FCC Rules provided it
is assembled in exact accordance with the instructions provided with this kit.
Operation is subject to the following conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received including interference that
may cause undesired operation.
Applies to PoE Products Only: This product is to be connected only to PoE
networks without routing to the outside plant.
TRENDnet
20675 Manhattan Place
Torrance, CA 90501
USA
Product Warranty Registration
Please take a moment to register your
product online. Go to TRENDnet’s website at:
www.trendnet.com/register
Technical Support
If you have any questions regarding the product
installation, please contact our Technical Support.
Toll free US/Canada: 1-866-845-3673
Regional phone numbers available
at www.trendnet.com/support
TV-NVR104 / TV-NVR104D2 (V1.1)