TRENDnet TEG-ECSX - User manual

TEG-ECTX
TEG-ECSX
H/W: V1
Quick Installation Guide

Table of Contents
Table of Contents
Version 10.30.2008
English .....................................................................................................
Troubleshooting ........................................................................................
1
1
2
6
1. Before You Start
2. .....................................................................................
................................................................................
How to Install

System Requirements
Application
Package Contents
1. Before You Start
English
1
?
?Driver CD-ROM
?Multi-Language Quick Installation
Guide
TEG-ECTX/TEG-ECSX
?
?CD-ROM Drive
?CPU: 300MHz or above / 800MHz or above (Windows Vista)
?Memory: 256MB RAM or above / 512MB RAM or above (Windows Vista)
?Windows 2000/2000 Server/XP(32-/64-bit)/2003 Server/Vista(32-/64-bit)
?RJ-45 Ethernet cable (TEG-ECTX)
?50/125ìm or 62.5/125ìm multi-mode fiber cable
(TEG-ECSX)
?Recommend fiber converter: TFC-1000MSC or TFC-2000MSC
?Recommend Gigabit Switch: TEG-S5 or TEG-S8
PCI Express 1.0a slot
Gigabit
Gigabit
24-Port Gigabit
Web Smart Switch
(TEG-240WS)
300Mbps Wireless N
Gigabit Router
(TEW-633GR)
1000Base-T to 1000Base-SX
Multi-Mode SC Fiber Converter
(TFC-2000MSC)
Internet
Cable/DSL
Modem
Gigabit Fiber PCI
Express Adapter
(TEG-ECSX)
Gigabit PCI
Express Adapter
(TEG-ECTX)

2. How to Install
English
2
1. Insert the Driver CD-ROM into
your computer’s CD-ROM Drive.
Note: Do not connect the TEG-ECTX/TEG-ECSX to your computer until
instructed to do so.
2. Click Run autorun.exe (Windows
Vista only).
4. Click Next. Then follow the
InstallShield Wizard instructions.
3. Click Install Driver, and then click
your operating system.

English
3
9. Drivers will install automatically.
7. Shutdown your computer and then
open your computer's case.
8. Insert the PCIe card firmly into an
available PCIe slot, and then turn
ON the computer and wait until the
Windows desktop appears.
6. Click Finish.
5. Click OK (Windows 2000/XP/2003
server only).

English
4
Connect the TEG-ECTX to your network
1. Connect a RJ-45 network cable
from the computer to an available
Ethernet port on your Gigabit
router or Gigabit switch.

Your installation is now complete.
For detailed information regarding the TEG- configuration and
advanced settings, please refer to User Guide on the Utility and Driver CD-
ROM.
TEG-ECTX/ ECSX
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
register your product Online at: www.trendnet.com/register
Thank you for choosing TRENDnet
English
5
1. Connect a SC-type multimode
cable from the TEG-ECSX to a
Gigabit fiber converter (e.g.
TFC-2000MSC).
Note: Make sure the TX and RX
cables are reversed on the
opposing connection.
Connect the TEG-ECSX to your network
2. Connect an Ethernet cable from
the Fiber converter to a Gigabit
Ethernet port on your switch (e.g.
TEG-S5).

6
Q1:
A1:
Q2:
A2:
Q3:
A3:
Q4:
A4:
Q5:
A5:
Windows doesn't recognize my new hardware. What should I do?
First, verify that your computer meets the system requirements as specified in
Section 1. Second, go to Start -> Control Panel -> System > Hardware ->
Device Manager. In the list of device types, double-click on Network Adapters.
If you see the device with a yellow question mark or exclamation point next to it,
double-click on it, click on Drivers and click Update Drivers. Third, if the device
manager fails to recognize the presence of a new networking adapter, verify that
the network adapter is firmly seated in the PCIE Slot.
Windows recognizes my new hardware, but I'm unable to connect to my
network. What should I do?
First, verify that the cable is securely connected from your switch or router to
your network adapter. Second, verify that the LEDs on your network card are lit.
Third, verify that the TCP/IP settings are set to Obtain an IP address
automatically.
Why am I only getting a network connection speed of 100Mbps instead of
1000Mbps for the TEG-ECTX?
First, check the Ethernet Cable. Make sure you are using CAT-5e or CAT-6
Ethernet Cables. Some CAT-5 cables are not rated to run in Gigabit. Second,
make sure you are connected to a 1000Mbps switch.
I am not getting a network connection when I connect the TEG-ECSX to my
network. What should I do?
First, check the fiber cable. Make sure you are using 50/125ìm or
62.5/125ìm multi-mode fiber cable. Second, make sure that the opposing
connection is Gigabit multi-mode fiber connection. The TEG-ECSX will not auto
negotiate to 10 or 100Mbps.
What is the maximum distance that is supported by the adapters?
TEG-ECTX: 100 Meters. TEG-ECSX: 550 meters.
If you still encounter problems or have any questions regarding the TEG-ECTX/TEG-
ECSX, please refer to the User's Guide included on the Driver CD-ROM or contact
Trendnet's Technical Support Department.
Troubleshooting

Certifications
This equipment has been tested and found to comply with FCC and CE Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received. Including interference that may
cause undesired operation.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
Waste electrical and electronic products must not
be disposed of with household waste. Please
recycle where facilities exist. Check with you Local
Authority or Retailer for recycling advice.
ADVERTENCIA
En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de alimentacón
necesario para su funcionamiento. El uso de un adaptador distinto al mencionado puede producir
daños fisicos y/o daños al equipo conectado. El adaptador de alimentación debe operar con voltaje y
frecuencia de la energia electrica domiciliaria existente en el pais o zona de instalación.

Copyright ©2008. All Rights Reserved. TRENDnet.
Product Warranty Registration
Please take a moment to register your product online.
Go to TRENDnet’s website at http://www.trendnet.com/register
20675 Manhattan Place
Torrance, CA 90501
USA