TRENDnet TEG-448WS - Switch User manual

Copyright ©2005. All Rights Reserved. TRENDware International, Inc.
TRENDnet
TRENDware, USA
What's Next in Networking
TEG-448WS
Version 05.04.2005
48-port 10/100/1000Mbps Copper Gigabit Smart Switch (Rack Mount)
Quick Installation Guide
Guide d'installation rapide
Commutateur intelligent Ethernet Gigabit cuivre
10/100/1000Mbps à 48 ports (montable sur rack)
48-facher 10/100/1000 MBit/s Kupfer-Gigabit-Smart-Switch (Einbau)
Kurzanleitung zur Installation
Guía de instalación rápida del
Conmutador Smart Gigabit de cobre (Rack Mount) de 48 puertos a 10/100/1000Mbps

Table of Contents
English ......................................................................................................
Troubleshooting ........................................................................................
1
1
2
3
4
5
10
1. Prepare for Installation ......................................................................
2. Product Detail ....................................................................................
3. Hardware Installation .........................................................................
4. Verify Installation ...............................................................................
5. Configuring the TEG-448WS ............................................................

Thank you for purchasing the TRENDnet TEG-448WS 48-port
10/100/1000Mbps Copper Gigabit Smart Switch (Rack Mount).
This guide will help you to install and configure the TEG-448WS. Installation
should be easy and trouble-free. If you experience any problems, please refer
to the Troubleshooting section. If you need further technical assistance, please
visit www.TRENDNET.com or contact technical support by phone.
Verify Package Contents
Please make sure you have everything in the box:
1
1. Prepare for Installation
English QIG
English
Minimum System Requirements
Before setting up the TEG-448WS, you should have the following:
1. Workstations with network cards
2. TCP/IP protocol installed in all workstations
3. A web browser such as Internet Explorer or Netscape Navigator
4. A RJ-45 Network Cable to connect your workstations to the TEG-448WS
5. (Optional) 4 Mini-GBIC modules (e.g. TEG-MGBSX)
TEG-448WS
AC Power Cord
Quick Installation Guide
Rubber Cushions: 4
Driver CD-ROM
Two Mounting brackets
with screws
Copyright ©2005. All Rights Reserved. TRENDware International, Inc.
TRENDnet
TRENDware, USA
What's Next in Networking
TEG-448WS
Version 05.04.2005
48-port 10/100/1000Mbps Copper Gigabit Smart Switch (Rack Mount)
Quick Installation Guide
Guide d'installation rapide
Commutateur intelligent Ethernet Gigabit cuivre
10/100/1000Mbps à 48 ports (montable sur rack)
48-facher 10/100/1000 MBit/s Kupfer-Gigabit-Smart-Switch (Einbau)
Kurzanleitung zur Installation
Guía de instalación rápida del
Conmutador Smart Gigabit de cobre (Rack Mount) de 48 puertos a 10/100/1000Mbps

2
2. Product Detail
The TEG-448WS has 48 10/100/1000 Mbps ports that support auto negotiation
and Auto-MDIX. It also has LED's that indicate power, system activity, network
speed, and network activity.
English
Power
system activity
network speed/network acitivity

3
3. Hardware Installation
English
Please keep in mind that the site where you install the TEG-448WS may
greatly affect its performance. Refer to the User's Guide in the provided CD-
ROM for optimal installation.
1. Connect AC Power cord to the back of the TEG-448WS.
2. Using a RJ-45 network cable (CAT 5 cable), connect your workstation to the
TEG-448WS.
Note: If you would like to verify the TEG-448WS has been properly
installed, please go to the Verify Installation section.
Congratulations!
Installation is now complete.

4English
Verify the following LED display:
1. Make sure that the power LED is on.
2. Verify that the System LED is blinking.
3. Verify that the connected workstation has the Link/Act LED on and a network
LED on.
4. Verify Installation
1
2
3

5English
5. Configuring the TEG-448WS
Note: For MAC Users, change your computers IP address to
192.168.0.X (where X is an available number from 1-253), and enter
http:\\192.168.0.1 in your web browser to access the TEG-448WS
Web Utility.
For Windows Users
1. Insert the TEG-448WS CD-ROM into your computer's CD-ROM drive.
2. Double-click My Computer on your desktop, double-click CD-ROM, double-
click Web-Management Utility, and double click Setup to install the
Configuration Program.
3. Click Next to start the installation.

6English
4. Click Next.
5. Click Next.

7English
6. Click Next.
7. Check Run web_management_utility. Click OK.

8English
8. Click Discovery, Click the TEG-448WS, and Click Configuration Setting.
9. In the Configuration window, type in the IP Address and Gateway that
applies to your network segment, and type admin as your password. Click
Set.
10. Click OK.