TRENDnet TEG-S18TXE User manual

TEG-S18TXE
Version 10.19.2005
User’s Guide
Copyright ©2005. All Rights Reserved. TRENDnet.

Table of Contents
English ............................................................................................
Românǎ ..........................................................................................
1
6
1
6
2
7
4
9
11
1. Introduction .............................................................................
2. Unpacking and Setup ..............................................................
3. Identifying External Components ............................................
1. Introducere ..............................................................................
2. Despachetare si instalare .......................................................
3. Identificarea componentelor externe .......................................
Technical Specifications ..................................................................

This section describes the features of the 8-Port 1000BASE-T Gigabit Ethernet
Switch.
Features
The 8-Port 1000BASE-T Gigabit Ethernet Switch was designed for easy
installation and high performance in an environment where traffic on the
network and the number of users increase continuously.
1
1. Introduction
English UG
English
8 1000BASE-T Gigabit Ethernet ports
Supports Auto-Negotiation for speed and duplex mode
Supports Auto-MDIX for each port
Support Full/Half duplex transfer mode for 10 and 100Mbps
Support Full duplex transfer mode for 1000Mbps
Full wire speed reception and transmission
Store-and-Forward switching method
Supports 4K absolute MAC addresses
Supports 128K Bytes RAM for data buffering
Extensive front-panel diagnostic LEDs
IEEE 802.3x flow control for full-duplex
Back pressure flow control for half-duplex

2English
2. Unpacking and Setup
This chapter provides unpacking and setup information for the Switch.
Unpacking
Open the shipping carton of the Switch and carefully unpack its contents. The
carton should contain the following items:
If any item is found missing or damaged, please contact your local reseller for
replacement.
TEG-S18TXE
User's Guide
Four rubber feet with
adhesive backing
One external power adapter
TEG-S18TXE
Version 10.19.2005
User’s Guide
Copyright ©2005. All Rights Reserved. TRENDnet.

3English
Setup
The setup of the Switch can be performed using the following steps:
Install the Switch in a fairly cool and dry place. See Technical
Specification for the acceptable operation temerature and humidity
ranges.
Install the Switch in a site free from strong electromagnetic
source,vibration, dust,and direct sunlight.
Leave at least 10cm of space at the left and right hand side of the Switch
for ventilation.
Visually inspect the DC power jack and make sure that it is fully secured
to the power adapter.

4English
3. Identifying External Components
The front panel of the Switch consists of eight 1000BASE-T ports and LED
indicators.
This chapter describes the front panel, rear panel and LED indicators of the
Switch
Front Panel
Front panel view of the Switch
Rear panel view of the Switch
1000BASE-T Ports:
Eight Gigabit Ethernet ports of 10/100/1000Mbps Auto-Negotiation interface.
LED Indicators
Comprehensive LED indicators display the conditions of the Switch and status
of the network. A description of these LED indicators follows (see LED
Indicators).
DC Power Jack:
Power is supplied through an external AC power adapter. Check the technical
specification section for information about the AC power input voltage.
Rear Panel
The rear panel of the Switch consists of an DC power connector. The following
figure shows the rear panel of the Switch.

5English
The LED indicators of the Switch include Power, Link/Act, 1000Mbps and
100Mbps. The following shows the LED indicators for the Switch along with an
explanation of each indicator.
LED Indicators
This indicator lights green when the Switch is receiving power, otherwise,
it is off.
These LED indicators are lighted up when there is a secure connection (or
link) to the desired port. The LED indicators blinking whenever there is
reception or transmission (i.e. ActivityACT) of data occurring at a port.
These LED indicators are lighted up when there is a secure connection (or
link) to 1000Mbps Gigabit Ethernet device at the desired port.
These LED indicators are lighted up when there is a secure connection (or
link) to 100Mbps Fast Ethernet device at the desired port.
Power:
Link/ACT:
1000Mbps:
100Mbps:
When the connection (or link) is 10Mbps, both of 1000Mbps and 100Mbps LED
indicators are off.

6
1. Introducere
Românǎ
Românǎ
Aceasta sectiune descrie caracteristicile switch-ului cu 8 porturi 1000BASE-T
Gigabit Ethernet.
Caracteristici
Switch-ul cu 8 porturi 1000BASE-T Gigabit Ethernet a fost creat pentru o
instalare rapida si performanta inalta intr-un mediu unde traficul din retea si
numarul de utilizatori creste continuu.
8 porturi 1000BASE-T Gigabit Ethernet
Suporta Auto-Negociere pentru pentru viteza si mod duplex
Suporta Auto-MDIX pentru fiecare port
Suporta mod de transfer Full/Half duplex pentru 10 si 100Mbps
Suporta mod de transfer Full duplex pentru 1000Mbps
Receptie si transmisie Full wire speed
Metoda de comutare Store-and-Forward
Suporta adrese 4K absolut MAC
Suporta 128KBytes RAM pentru buffer date
Panou frontal cu LED-uri de diagnosticare extensiva
Control trafic IEEE 802.3x pentru full-duplex
Control trafic pentru half-duplex

7
2. Despachetare si instalare
Românǎ
Acest capitol ofera informatii despre despachetare si instalare a switch-ului.
Despachetare
Deschideti cartonul switch-ului si despachetati cu grija continutul. Cutia ar
trebui sa contina urmatoarele obiecte:
Daca vreunul dintre obiecte lipseste sau e deteriorat, va rugam sa contactati
vanzatorul local pentru inlocuire.
TEG-S18TXE
Acest ghid de utilizare
Patru picioruse de
cauciuc cu adeziv
Un adaptor extern de alimentare
TEG-S18TXE
Version 10.19.2005
User’s Guide
Copyright ©2005. All Rights Reserved. TRENDnet.

8Românǎ
Instalare
Instalarea switch-ului poate fi facuta urmand acesti pasi:
Instalati switch-ul intr-un loc racoros si uscat. Vedeti Specificatii tehnice
pentru temperatura de operare si gradul de umiditate acceptabile.
Instalati switch-ul intr-un loc fara surse electromagnetice puternice,vibratii,
praf si lumina solara directa.
Lasati cel putin 10cm de spatiu pe lateralele switch-ului pentru ventilare.
Inspectati vizual mufa alimentatorului DC si asigurati-va ca este bine fixat
in adaptorul de alimentare.