TRENDnet TEW-671BR User manual

Quick Installation Guide
TEW-671BR
1.01

Table of Contents
Table of Contents
English ......................................................................................................
Troubleshooting ........................................................................................
1
1
2
3
7
1. Before You Start
2. Hardware Installation .........................................................................
3.
.................................................................................
Configure the Wireless Router ...........................................................
Version 06.17.2009

Installation Requirements
Application
Package Contents
1. Before You Start
English
1
?
?
?
?
Acomputer with a wired or wireless network adapter properly installed
Web Browser: Internet Explorer (6.0 or higher)
Broadband Internet
Installed Cable or DSLModem
Wireless n (802.11n) 2.4GHz Wireless n (802.11n) 5GHz
300Mbps Dual Band
Wireless N Router
(TEW-671BR)
Laptop with
Wireless N USB Adapter
(TEW-624UB)
Modem
Internet
Workstation with 300Mbps Dual
Band Wireless N USB Adapter
(TEW-664UB)
Media Center
Workstation with 300Mbps Dual
Band Wireless N USB Adapter
(TEW-664UB)
?
?
?
?
?
TEW-671BR
Multi-Language Quick Installation
Guide
CD-ROM (User's Guide)
Cat.5 Ethernet cable (1m / 3.2ft)
PowerAdapter (12V, 1A)

English
2
2. Hardware Installation
Note: Gather all information related to your Internet Connection before you
start. If necessary, contact your Internet Service Provider (ISP).
1. Verify that you have an Internet
connection when connecting your
computer directly to the Cable or
DSLmodem.
Cable/DSL Modem
Internet
5. Verify that the following panel lights
are on: POWER, LAN(1,2,3 or 4),
WAN and WLAN (2.4GHz/5GHz) .
2. Connect one end of a RJ-45 cable
to the TEW-671BR’s WAN port.
Connect the other end of the cable
to your modem.
4. Connect theAC PowerAdapter to
the wireless router and then to a
power outlet.
3. Connect one end of a RJ-45 cable
to one of the TEW-671BR’s LAN
ports. Connect the other end of the
cable to your computer.

English
3
3. Configure the Wireless Router
Note: It is recommended that you configure the Wireless Router from a wired
computer and your PC's IP address is set to receive an IPaddress
automatically (see troubleshooting section).
1. Open your web browser, type
http://192.168.10.1 in the
Address bar, and then press Enter.
4. Click Next.
2. Enter the User Name and
Password, and then click OK.
By default:
User Name: admin
Password: admin
3. Click Wizard.

English
4
5. Click Next.
6. The TEW-671BR will attempt to
auto detect your Internet
connection. Follow the wizard
instructions and continue on to
step 8.
8. Follow the wizard instructions to
complete the configuration.
Note: Each Internet Connection
type may have different options.
Configure the settings based on
information provided by your ISP.
7. This screen will appear if the
TEW-671BR is unable to auto
detect your Internet connection.
Click Manual Config.

English
5
9. Use your mouse to select the
desired security level (lowest for no
encryption, highest for WPA2-
PSK).
11. Use your mouse to select the
desired security level (lowest for
WEP, highest for WPA2-PSK).
12. Enter the desired SSID and Key.
Then click Next. By default, the
SSID for 5G WLAN is
TRENDnet671A.
10. Enter the desired SSID and Key.
Then click Next. By default, the
SSID for 2.4G WLAN is
TRENDnet671N.
Note: The examples below are for WPA2-PSK security. If you select WPA-
PSK or WPA2-PSK, make sure your wireless adapters support WPAor WPA2.
If your wireless adapters do not support WPAor WPA2, then select WEP.

English
6
Your configuration is now complete.
For detailed information regarding the TEW-671BR’s configuration and
advanced settings, please refer to the Troubleshooting section, User's Guide
CD-ROM, or TRENDnet's website at http://www.trendnet.com.
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
register your product Online at: www.trendnet.com/register
Thank you for choosing TRENDnet
13. Setup is successful. Click
Reboot.

7
Troubleshooting
2. Click Internet Protocol Version
4(TCP/IPv4) and then click Properties.
Then click on Obtain an IP address
automatically.
Q1:
A1:
I typed http://192.168.10.1 in my Internet Browser'sAddress Bar, but an error
message says “The page cannot be displayed.” How can I get into the TEW-
671BR's web configuration page?
First, check your hardware settings again by following the instructions in
Section 2. Second, make sure the LAN (1,2,3 or 4) and WLAN(2.4GHz/5GHz)
lights are lit. Third, make sure your TCP/IPsettings are set to Obtain an IP
address automatically (see the steps below).
1. Go into the Control Panel, click
Network and Internet, click Network
and Sharing Center, click Manage
Network Connections and then right-
click the Local Area Connection icon
and then click Properties.
Windows Vista
1. Go into the Control Panel, double-click
the Network Connections icon and
then right-click the Local Area
Connection icon and then click
Properties.
Windows XP/2000

8
Fourth, press on the factory reset button for 15 seconds.
I am not sure what type of InternetAccount Type I have for my Cable/DSL
connection. How do I find out?
Contact your Internet Service Provider's (ISP) support service for the correct
information.
I configured my router with my ISP settings, but I can not get onto the
Internet. What should I do?
First, verify that you can get onto the Internet with a direct connection into your
modem. Second, contact your ISP and verify all the information that you have in
regards to your Internet connection settings is correct. Third, power cycle your
modem and router. Unplug the power to the modem and router. Wait 30
seconds, and then reconnect the power to the modem. Wait for the modem to fully
boot up, and then reconnect the power to the router.
All the settings are correct, but I can not make a wireless connection to the
Router. What should I do?
First, double check that the WLAN (2.4GHz/5GHz) light on the Wireless
Router is lit. Second, power cycle the TEW-671BR. Unplug the power to the
TEW-671BR. Wait 15 seconds, then plug the power back in to the TEW-671BR.
Third, contact the manufacturer of your wireless network adapter and make sure
the wireless network adapter is configured with the proper SSID. The preset SSID
of theAccess Point is TRENDnet671N (2.4GHz) and TRENDnet671A (5GHz).
If you still encounter problems or have any questions regarding the TEW-671BR, please
contact TRENDnet'sTechnical Support Department.
Q2:
A2:
Q3:
A3:
Q4:
A4:
2. Click Internet Protocol (TCP/IP) and
then click Properties. Then click on
Obtain an IP address automatically.