Tridonic EM powerLED BASIC FX 103 SR 50W 50V User manual

www.tridonic.com 1
Subject to change without notice. Information provided without guarantee.
Data sheet 03/20-EM042-21
Emergency lighting units
EM powerLED
Product description
• Independent fixed output LED Driver for mains operation with
integrated Simple CORRIDOR FUNCTION (CF)
• Emergency lighting LED Driver with manual test function
• For self-contained emergency lighting
• For LED modules with a forward voltage of 15 – 50 V
• SELV for output voltage < 60 V DC
• Compact plastic casing (209 x 82 x 34 mm) with strain relief
• 5 years guarantee
Properties
• 4.9 – 50 W output power
• Constant current LED operation
• 300 – 1,400 mA output current in mains operation selectable
with I-SELECT PLUG in steps of 50 mA
• Simple CORRIDOR FUNCTION (CF) with 10 % light level
• Integrated emergency lighting unit
• 1 or 3 h rated duration selectable with plug (duration link)
• Automatic shutdown of output if LED load is out of range
• Green charge status display LED
• Electronic charge system
• Polarity reversal protection for battery
• Deep discharge protection
• Short-circuit-proof battery connection
Batteries
• High-temperature cells
• NiCd or NiMH batteries
• D, Cs, LA or LAL cells
• 4-year design life
• 1-year guarantee
• For battery compatibility refer to table „Battery selection“
È
Standards, page 10
Wiring diagrams and installation examples, page 11
EM powerLED BASIC FX SR 50 W
Combined emergency lighting LED Driver

www.tridonic.com 2
Subject to change without notice. Information provided without guarantee.
Data sheet 03/20-EM042-21
Emergency lighting units
EM powerLED
EL
Technical data
Rated supply voltage 220 – 240 V
Mains frequency 50 / 60 Hz
Typ. λ (at 230 V, 50 Hz, normal ope-
ration)
0.95
Typ. λ (at 230 V, 50 Hz, CF operation) 0.45
Overvoltage protection 320 V (for 1 h)
Battery charging time 24 h
Max. open circuit voltage 60 V
Time to light < 0.5 s from detection of emergency event
Typ. power consumption in charging 3.5 W
Output LF current ripple (< 120 Hz) < 2 %
Output current tolerance 7 %
THD normal operation < 20 %
THD CF operation < 30 %
Ambient temperature ta > 40 W
output power
40 °C
Ambient temperature ta ≤ 40 W
output power
50 °C
Max. casing temperature tc 80 °C
Dimensions LxBxH 209 x 82 x 34 mm
Mains voltage changeover threshold according to EN 60598-2-22
Type of protection IP20
Charge current 1h 100 mA
Charge current 3h 200 mA
Discharge current 1h 960 mA
Discharge current 3h 960 mA
EM powerLED BASIC FX SR 50 W
Combined emergency lighting LED Driver
ø4,5
ø 86
33 34
82
175,5
209
Dur
ation
link 3
h
No
du
ration
link 1
h
Note: LED Driver supplied with duration link in 3 hours position. Remove duration link for
1 hour duration. Duration link and I-SELECT PLUG must be set before battery and mains
connection.
Ordering data
Type3Article
number
Rated
duration
Number
of cells
Packaging,
carton
Packaging,
pallet
Weight
per pc.
EM powerLED BASIC FX 103 SR 50W 50V 89800430 1/3 h 310 pc(s). 400 pc(s). 0.29 kg
EM powerLED BASIC FX 104 SR 50W 50V 89800412 1/3 h 410 pc(s). 400 pc(s). 0.29 kg

www.tridonic.com 3
Subject to change without notice. Information provided without guarantee.
Data sheet 03/20-EM042-21
Emergency lighting units
EM powerLED
Specific technical data
Type3Number
of battery
cells
Output
current
Min.
output
voltage2
Max.
output
voltage2
Min.
output
power
Max.
output
power
Input power
(at 230 V, 50
Hz, full load)
Input current
(at 230 V, 50 Hz,
full load)
Eiciency
(at 230 V,
50 Hz)
λ
(at 230 V, 50
Hz, full load)
Ambient
temperature
ta1
tc/ta for ≥
50.000 h1I sel resistor value
Normal operation
EM powerLED BASIC FX
103 / 104 SR 50W 50V
– 300 mA 16.6 V 50.0 V 5.0 W 15.0 W 20 W 110 mA 74 0.80 -5 ... 50 °C 79 / 50 °C open
– 350 mA 16.6 V 50.0 V 5.8 W 17.5 W 22 W 120 mA 79 0.80 -5 ... 50 °C 79 / 50 °C 69.80 kΩ
– 400 mA 16.6 V 50.0 V 6.6 W 20.0 W 25 W 130 mA 79 0.85 -5 ... 50 °C 79 / 50 °C 62.00 kΩ
– 450 mA 16.6 V 50.0 V 7. 5 W 22.5 W 27 W 140 mA 82 0.85 -5 ... 50 °C 79 / 50 °C 56.00 kΩ
– 500 mA 16.6 V 50.0 V 8.3 W 25.0 W 31 W 150 mA 81 0.90 -5 ... 50 °C 79 / 50 °C 48.70 kΩ
– 550 mA 16.6 V 50.0 V 9.1 W 27.5 W 34 W 165 mA 81 0.90 -5 ... 50 °C 79 / 50 °C 43.20 kΩ
– 600 mA 16.6 V 50.0 V 10.0 W 30.0 W 36 W 175 mA 83 0.90 -5 ... 50 °C 79 / 50 °C 36.50 kΩ
– 650 mA 16.6 V 50.0 V 10.8 W 32.5 W 40 W 185 mA 81 0.90 -5 ... 50 °C 79 / 50 °C 28.70 kΩ
– 700 mA 16.6 V 50.0 V 11.6 W 35.0 W 44 W 200 mA 80 0.95 -5 ... 50 °C 79 / 50 °C 24.00 kΩ
– 750 mA 16.6 V 50.0 V 12.5 W 37.5 W 46 W 210 mA 82 0.95 -5 ... 50 °C 79 / 50 °C 20.50 kΩ
– 800 mA 16.6 V 50.0 V 13.3 W 40.0 W 49 W 225 mA 81 0.95 -5 ... 50 °C 79 / 50 °C 18.00 kΩ
– 850 mA 16.6 V 50.0 V 14.1 W 42.5 W 52 W 235 mA 81 0.95 -5 ... 40 °C 76 / 40 °C 16.00 kΩ
– 900 mA 16.6 V 50.0 V 15.0 W 45.0 W 55 W 250 mA 82 0.95 -5 ... 40 °C 76 / 40 °C 13.30 kΩ
– 950 mA 15.7 V 50.0 V 15.0 W 47.5 W 58 W 265 mA 82 0.95 -5 ... 40 °C 76 / 40 °C 11.00 kΩ
– 1,000 mA 15.0 V 50.0 V 15.0 W 50.0 W 61 W 275 mA 82 0.97 -5 ... 40 °C 76 / 40 °C 9.31 kΩ
– 1,050 mA 15.0 V 47.6 V 15.0 W 50.0 W 60 W 280 mA 84 0.97 -5 ... 40 °C 76 / 40 °C 7.87 kΩ
– 1,100 mA 15.0 V 45.5 V 15.0 W 50.0 W 60 W 280 mA 88 0.97 -5 ... 40 °C 76 / 40 °C 6.49 kΩ
– 1,150 mA 15.0 V 43.5 V 15.0 W 50.0 W 60 W 280 mA 88 0.97 -5 ... 40 °C 76 / 40 °C 4.70 kΩ
– 1,200 mA 15.0 V 41.7 V 15.0 W 50.0 W 60 W 280 mA 88 0.97 -5 ... 40 °C 76 / 40 °C 3.83 kΩ
– 1,250 mA 15.0 V 40.0 V 15.0 W 50.0 W 60 W 280 mA 88 0.97 -5 ... 40 °C 76 / 40 °C 2.70 kΩ
– 1,300 mA 15.0 V 38.5 V 15.0 W 50.0 W 60 W 280 mA 88 0.97 -5 ... 40 °C 76 / 40 °C 2.20 kΩ
– 1,350 mA 15.0 V 37.0 V 15.0 W 50.0 W 61 W 280 mA 87 0.97 -5 ... 40 °C 76 / 40 °C 1.50 kΩ
–1,400 mA 15.0 V 35.0 V 15.0 W 50.0 W 62 W 285 mA 87 0.97 -5 ... 40 °C 76 / 40 °C short circuit
(0 Ω)
CF operation
EM powerLED BASIC FX
103 / 104 SR 50W 50V
– 30 mA – – 0.5 W 1.7 W 4.0 W 50 mA 50 0.40 – – open
– 38 mA – – 0.6 W 2.1 W 4.5 W 50 mA 56 0.40 – – 69.80 kΩ
– 39 mA – – 0.6 W 2 .1 W 4.5 W 50 mA 56 0.40 – – 62.00 kΩ
– 52 mA – –0.9 W 2.9 W 5.0 W 55 mA 60 0.40 – – 56.00 kΩ
– 52 mA – – 0.9 W 2.9 W 5.0 W 55 mA 60 0.40 – – 48.70 kΩ
– 52 mA – – 0.9 W 2.9 W 5.0 W 55 mA 70 0.40 – – 43.20 kΩ
– 66 mA – – 1.1 W 3.6 W 5.5 W 55 mA 73 0.45 – – 36.50 kΩ
– 69 mA – – 1.1 W 3.8 W 5.5 W 55 mA 73 0.45 – – 28.70 kΩ
– 80 mA – – 1.3 W 4.4 W 6.0 W 60 mA 75 0.45 – – 24.00 kΩ
– 83 mA – – 1.4 W 4.6 W 6.0 W 60 mA 83 0.45 – – 20.50 kΩ
– 85 mA – – 1.4 W 4.7 W 6.0 W 60 mA 83 0.45 – – 18.00 kΩ
– 92 mA – – 1.5 W 5.1 W 6.5 W 60 mA 85 0.50 – – 16.00 kΩ
– 92 mA – – 1.5 W 5.1 W 6.5 W 60 mA 92 0.50 – – 13.30 kΩ
– 105 mA – – 1.6 W 5.8 W 7.0 W 60 mA 86 0.50 – – 11.00 kΩ
– 106 mA – – 1.6 W 5.8 W 7.0 W 60 mA 86 0.50 – – 9.31 kΩ
– 118 mA – – 1.8 W 6.2 W 7. 5 W 65 mA 87 0.55 – – 7.87 kΩ
– 119 mA – – 1.8 W 6.0 W 7. 5 W 65 mA 87 0.55 – – 6.49 kΩ
– 130 mA – – 2.0 W 6.2 W 8.0 W 65 mA 88 0.55 – – 4.70 kΩ
– 131 mA – – 2.0 W 6.0 W 8.0 W 65 mA 88 0.55 – – 3.83 kΩ
– 144 mA – – 2.2 W 6.3 W 8.0 W 65 mA 88 0.55 – – 2.70 kΩ
– 144 mA – – 2.2 W 6.1 W 8.0 W 65 mA 88 0.60 – – 2.20 kΩ
– 145 mA – – 2.2 W 5.9 W 8.5 W 65 mA 88 0.60 – – 1.50 kΩ
–158 mA – – 2.4 W 6.1 W 9.0 W 70 mA 83 0.60 – – short circuit
(0 Ω)
Emergency operation
EM powerLED BASIC FX
103 SR 50W 50V 3 see page 8 15 V 50 V 2.1 W 2.75 W – – – – – – all
EM powerLED BASIC FX
104 SR 50W 50V 4 see page 8 15 V 50 V 2.7 W 3.50 W – – – – – – all
1Ambient temperature range ta defined in normal operation
2Output voltage range defined in normal operation. LED forward voltage will decrease in CF operation.
3 EM = Emergency
y

www.tridonic.com 4
Subject to change without notice. Information provided without guarantee.
Data sheet 03/20-EM042-21
Emergency lighting units
EM powerLED
Product description
• For connection to the emergency lighting LED Driver
• For checking the device function
Test switch EM2
ACCES-
SORIES
Ordering data
Type Article number Packaging,
bag
Packaging,
carton
Weight
per pc.
Test switch EM 2 89805277 25 pc(s). 600 pc(s). 0.009 kg
Product description
• A green LED indicates that charging current is flowing into the
battery
Status indication green LED
ACCES-
SORIES
Ordering data
Type Article number Packaging,
bag
Packaging,
carton
Weight
per pc.
LED EM green 89899605 25 pc(s). 200 pc(s). 0.011 kg
LED EM green, ultra high brightness 89899756 25 pc(s). 200 pc(s). 0.012 kg
smartSWITCH HF 5DP f
Automatic switching based on motion and light level
ACCES-
SORIES
smartSWITCH HF 5DP f
smartSWITCH HF 5DP S f
Ordering data
Type Article number Dimensions
L x W x H
Packaging,
carton
Weight
per pc.
smartSWITCH HF 5DP f 28002214 70 x 36.5 x 24.5 mm 5 pc(s). 0.040 kg
smartSWITCH HF 5DP S f 28002235 58 x 48.5 x 24.5 mm 5 pc(s). 0.040 kg

www.tridonic.com 5
Subject to change without notice. Information provided without guarantee.
Data sheet 03/20-EM042-21
Emergency lighting units
EM powerLED
Product description
• Motion detector for luminaire installation
• Motion detection through glass and thin materials (except metal)
• For automatic on/o switching of electronic ballasts
• Bright-out function: luminaire is not switched on if there is
adequate brightness
• Delay time, detection range and light value for the bright-out
function can be set via 9 dip switches
• Max. installation height 5 m
• Two housing options allowing flexible installation
• Variable detection area (100 – 10 %)
• Zero cross switching supported
• 5-year guarantee
smartSWITCH HF 5DP f
Automatic switching based on motion and light level
ACCES-
SORIES
smartSWITCH HF 5DP f
smartSWITCH HF 5DP S f
Ordering data
Type Article number Dimensions
L x W x H
Packaging,
carton
Weight
per pc.
smartSWITCH HF 5DP f 28002214 70 x 36.5 x 24.5 mm 5 pc(s). 0.040 kg
smartSWITCH HF 5DP S f 28002235 58 x 48.5 x 24.5 mm 5 pc(s). 0.040 kg

www.tridonic.com 6
Subject to change without notice. Information provided without guarantee.
Data sheet 03/20-EM042-21
Emergency lighting units
EM powerLED
Product description
• Ready-for-use resistor to set output current value
• Resistor is base insulated
• Resistor power 0.25 W
• Resistor value tolerance ± 1 %
I-SELECT PLUG E
ACCES-
SORIES
3,5
xxxx
5,5 3,5
613,5
9
Ordering data
Type Article
number Colour Marking Resistor value
Packaging
bag Weight per pc.
I-SELECT PLUG E 28001167 Green 69k8 69.80 kΩ 10 pc(s). 0.001 kg
I-SELECT PLUG E 28001166 Green 62k 62.00 kΩ 10 pc(s). 0.001 kg
I-SELECT PLUG E 28000627 Green 56k 56.00 kΩ 10 pc(s). 0.001 kg
I-SELECT PLUG E 28000626 Green 48k7 48.70 kΩ 10 pc(s). 0.001 kg
I-SELECT PLUG E 28000625 Green 43k2 43.20 kΩ 10 pc(s). 0.001 kg
I-SELECT PLUG E 28000624 Green 36k5 36.50 kΩ 10 pc(s). 0.001 kg
I-SELECT PLUG E 28000622 Green 28k7 28.70 kΩ 10 pc(s). 0.001 kg
I-SELECT PLUG E 28001165 Green 24k 24.00 kΩ 10 pc(s). 0.001 kg
I-SELECT PLUG E 28001164 Green 20k5 20.50 kΩ 10 pc(s). 0.001 kg
I-SELECT PLUG E 28001163 Green 18k 18.00 kΩ 10 pc(s). 0.001 kg
I-SELECT PLUG E 28001162 Green 16k 16.00 kΩ 10 pc(s). 0.001 kg
I-SELECT PLUG E 28001161 Green 13k3 13.30 kΩ 10 pc(s). 0.001 kg
I-SELECT PLUG E 28001160 Green 11k 11.00 kΩ 10 pc(s). 0.001 kg
I-SELECT PLUG E 28000617 Green 9k31 9.31 kΩ 10 pc(s). 0.001 kg
I-SELECT PLUG E 28001159 Green 7k87 7.87 kΩ 10 pc(s). 0.001 kg
I-SELECT PLUG E 28000616 Green 6k49 6.49 kΩ 10 pc(s). 0.001 kg
I-SELECT PLUG E 28001158 Green 4k7 4.70 kΩ 10 pc(s). 0.001 kg
I-SELECT PLUG E 28001157 Green 3k83 3.83 kΩ 10 pc(s). 0.001 kg
I-SELECT PLUG E 28001156 Green 2k7 2.70 kΩ 10 pc(s). 0.001 kg
I-SELECT PLUG E 28001155 Green 2k2 2.20 kΩ 10 pc(s). 0.001 kg
I-SELECT PLUG E 28001154 Green 1k5 1.50 kΩ 10 pc(s). 0.001 kg
I-SELECT PLUG E 28000612 Green 0R 0 kΩ 10 pc(s). 0.001 kg
NiCd Battery pack 1.8 – 4.5 Ah
Batteries
ACCES-
SORIES
Ordering data
Type Article number Packaging, carton Weight per pc.
Battery pack 1.8 Ah with plug
Pack-NiCd 3C CON 28001221 5 pc(s). 0.270 kg
Pack-NiCd 4C CON 28001222 5 pc(s). 0.320 kg
Battery pack 4.5 Ah with plug
Pack-NiCd 3D CON 89800389 5 pc(s). 0.534 kg
Pack-NiCd 4D CON 89800390 5 pc(s). 0.661 kg

www.tridonic.com 7
Subject to change without notice. Information provided without guarantee.
Data sheet 03/20-EM042-21
Emergency lighting units
EM powerLED
Product description
• High-temperature NiCd battery pack for use with emergency
lighting units
Properties
• Constant high-temperature operation – depending on the emer-
gency lighting unit used (refer to respective emergency control
gear datasheet)
• Good charging properties at high temperature
• High energy maintenance of the charged battery
• 4 year life-time in operation at max. temperature
• Certified quality manufacturer
• Casing material made of polycarbonate
• 0.2 m double-insulated cable with plug connection
• 0.8 m double-insulated cable with plug and pre-stripped ends for
connection with the emergency unit
• 1.0 mm² solid wire, pre-stripped
• Suitable for emergency lighting equipment as per
IEC 60598-2-22
NiCd Battery pack 1.8 – 4.5 Ah
Batteries
ACCES-
SORIES
Ordering data
Type Article number Packaging, carton Weight per pc.
Battery pack 1.8 Ah with plug
Pack-NiCd 3C CON 28001221 5 pc(s). 0.270 kg
Pack-NiCd 4C CON 28001222 5 pc(s). 0.320 kg
Battery pack 4.5 Ah with plug
Pack-NiCd 3D CON 89800389 5 pc(s). 0.534 kg
Pack-NiCd 4D CON 89800390 5 pc(s). 0.661 kg

www.tridonic.com 8
Subject to change without notice. Information provided without guarantee.
Data sheet 03/20-EM042-21
Emergency lighting units
EM powerLED
NiMH Battery pack 2.2 – 4.0 Ah
Batteries
ACCES-
SORIES
Fig. 1
Fig. 2
Battery pack 2.2 Ah
Pack-NiMH 2.2Ah 3 CON  5 pc(s). 25 pc(s). 0.32 kg
Pack-NiMH 2.2Ah 4 CON  5 pc(s). 25 pc(s). 0.36 kg
Battery pack 4.0 Ah
Pack-NiMH 4Ah 3 CON  5 pc(s). 25 pc(s). 0.40 kg
Pack-NiMH 4Ah 4 CON  5 pc(s). 25 pc(s). 0.48 kg
Product description
• High-temperature NiMH battery pack for use
with emergency lighting units
• 4-year design life
• 1-year guarantee
Properties
• Constant high-temperature operation
• Temperature depending on the used emergency lighting unit
(refer to respective emergency control gear datasheet)
• Good charging properties at high temperature
• High energy maintenance of the charged battery
• Certified quality manufacturer
• Casing material made of polycarbonate
• 1.0 mm² stranded wire
• Suitable for emergency lighting equipment as per IEC 60598-2-
22
ACD EM LED INDICATOR HOLDER
ACCES-
SORIES
ø39,95
ø6
ø19,9
ø26,29
42,9
ø35
1,8
6,8
13
Ordering data
Type Article
number Colour Packaging carton Weight per pc.
ACD EM LED INDICATOR HOLDER 28002189 White 10 pc(s). 0.010 kg

www.tridonic.com 9
Subject to change without notice. Information provided without guarantee.
Data sheet 03/20-EM042-21
Emergency lighting units
EM powerLED
ACD EM LED INDICATOR HOLDER
ACCES-
SORIES
ø39,95
ø6
ø19,9
ø26,29
42,9
ø35
1,8
6,8
13
Ordering data
Type Article
number Colour Packaging carton Weight per pc.
ACD EM LED INDICATOR HOLDER 28002189 White 10 pc(s). 0.010 kg
Product description
• Holder for indicator LED in emergency operation
• Glow-wire test with a temperature of 850 °C passed

www.tridonic.com 10
Subject to change without notice. Information provided without guarantee.
Data sheet 03/20-EM042-21
Emergency lighting units
EM powerLED
1. Standards
• EN 55015
• EN 61000-3-2
• EN 61000-3-3
• EN 61347-2-13
• EN 61547
• EN 62384
• EN 61347-2-7
• according to EN 50172
• according to EN 60598-2-22
1.1 Glow-wire test
according to EN 60598-1 with increased temperature of 850 °C passed.
1.2 Temperature range
According to the standard IEC 60598-1 a LED Driver for remote installation
has a max. case temperature of 90 °C. The ambient temperature range ta for
the EM powerLED BASIC FX SR 50W is defined to meet this requirement.
1.2 Insulation and electric strength testing of luminaires
Electronic LED Driver can be damaged by high voltage. This has to be consi-
dered during the routine testing of the luminaires in production.
According to IEC 60598-1 Annex Q (informative only!) or ENEC 303-Annex A,
each luminaire should be submitted to an insulation test with 500VDC for 1 se-
cond. This test voltage should be connected between the interconnected phase
and neutral terminals and the earth terminal. The insulation resistance must be
at least 2 MΩ.
As an alternative, IEC 60598-1 Annex Q describes a test of the electrical
strength with 1,500 VAC (or 1,414 x 1,500 VDC). To avoid damage to the electronic
devices this test must not be conducted.
2. Thermal data
2.1 Expected life-time
Average life-time 50,000 hours under rated conditions with a failure rate of
less than 10 %. Average failure rate of 0.2 % per 1000 operating hours.
2.2 Storage conditions
Humidity: 5 % up to max. 85 %,
not condensed
(max. 56 days/year at 85 %)
Storage temperature: -40 °C up to max. +80 °C
The devices have to be within the specified temperature range (ta) before
they are operated.
Expected life-time
Type Output
power ta 40 °C 50 °C
EM powerLED BASIC FX
103 / 104 SR 50W 50V
10 W tc 56 °C 66 °C
life-time > 100,000 h > 100,000 h
20 W tc 59 °C 69 °C
life-time > 100,000 h > 100,000
30 W tc 63 °C 73 °C
life-time > 100,000 h > 100,000 h
40 W tc 69 °C 79 °C
life-time > 100,000 h 90,000 h
50 W tc 76 °C x
life-time 95,000 h x
x = not permitted

www.tridonic.com 11
Subject to change without notice. Information provided without guarantee.
Data sheet 03/20-EM042-21
Emergency lighting units
EM powerLED
3. Installation / Wiring
3.1 Wiring diagrams
220–240 V
L
N
50/60 Hz
Tridonic Sensor
L
N
L´
EM powerLED
BASIC FX
N
L
+
–
+
–
–
+


S/L
C/F
L link
LED
Battery
Test switch
Duration link
Orange
Pink
Indication LED
I set
–
+
LED
module
15 – 50V
Wiring diagram EM powerLED BASIC FX without sensor Wiring diagram EM powerLED BASIC FX with sensor
PIR output ≙230 V
EM powerLED
BASIC FX
N
L
+
–
+
–
–
+


S/L
C/F
L link
LED
Battery
Test switch
Duration link
I set
220–240 V
L
N
50/60 Hz
–
+
LED
module
15 – 50V
Orange
Pink
Indication LED
When using the EM powerLED without a sensor, connect the terminals C / F and
L link with a wire.
The connected LED module will be used for mains and emergency operation.
The mains power must be removed before changing the LED load.
Secondary switching of LEDs is not allowed and may cause damage to the
LEDs. The hot plug-in of LEDs during normal operation may result in high
current peaks.
Note
The EM powerLED BASIC FX 50W uses pulse width modulation (PWM) for
the LED operation in CORRIDOR mode. This can have an adverse effect on
video recording equipment e.g. cctv.
Caution should be observed when using the CORRIDOR FUNCTION in cctv
monitored areas.
Switching behaviour
S/L C/F LED
o o off
o on off
on o 10 %
on on 100 %

www.tridonic.com 12
Subject to change without notice. Information provided without guarantee.
Data sheet 03/20-EM042-21
Emergency lighting units
EM powerLED
Wiring
Mains (N, L, C/F, L link, S/L)
LED (LED +, LED –)
Batteries (Bat +, Bat –)
I set
Maximum lead length
LED 3 m
status indication LED 1 m
batteries 1 m
Wiring
Test switch
Indication LED
Max. lead insulation diameter
Battery 2.1 mm
Test switch 2.1 mm
Indicator LED 2.1 mm
Use one wire for each terminal connector only.
Use each strain relief channel for one cable only.
max.
∅= 10 mm
min.
∅= 6,3 mm
8.5 – 9.5 mm
0.2 – 0.5 mm² solid or fine-stranded
0.25 mm² fine-stranded with ferrule
8.5 – 9.5 mm
0.5 – 1.5 mm2 solid or fine-stranded
0.5 – 1.0 mm2 fine-stranded with ferrule
Installation instruction
Max. torque for the mounting screws: 0.5 Nm / M4.
3.3 Release of the wiring
Press down the “push button” and remove
the cable from front.
3.2 Wiring type and cross-section
3.4 Fixing conditions
Dry, acidfree, oilfree, fatfree. It is not allowed to exceed the maximum ambi-
ent temperature (ta) stated on the device. Minimum distances stated below
are recommendations and depend on the actual luminaire. Is not suitable for
fixing in corner.
>100 mm
Leuchte
Luminaire >20 mm
>20 mm
3.5 Wiring guidelines
• The output to the LED is DC but has high frequency content, which should be
considered for good EMC compliance.
• LED leads should be separated from the mains connections and wiring for
good EMC performance.
• Maximum lead length on the LED terminals is 3 m. For a good EMC
performance keep the LED wiring as short as possible.
• The secondary wires (LED module) should be routed in parallel to ensure
good EMC performance.
• Maximum lead length for the Test switch and Indicator LED connection is 1 m.
The test switch and Indicator LED wiring should be separated from the LED
leads to prevent noise coupling.
• Battery leads are specified with 0.5 mm cross section and a length of 1.3 m.
• To avoid the damage of the control gear, the wiring must be protected against
short circuits to earth (sharp edged metal parts, metal cable clips, louver, etc.).
To ensure that a luminaire containing LED emergency units complies with
EN 55015 for radio frequency conducted interference in both normal and emer-
gency mode it is essential to follow good practice in the wiring layout.
Within the luminaire the switched and unswitched 50 Hz supply wiring must be
routed as short as possible and be kept as far away as possible from the LED
leads. Through wiring may affect the emc performance of the luminaire.
The length of LED leads must not be exceeded.
The output current depends on the forward voltage and the tolerance of the
LED modules.
4. Mechanical data
4.1 Housing properties
4.2 Mechanichal data accessories
LED status indicator
• Green
• Mounting hole 6.5 mm diameter, 1 – 1.6 mm thickness
• Lead length 0.3 m / 1.0 m
• Insulation rating: 90 °C
Test switch
• Mounting hole 7.0 mm diameter
• Lead length 0.55 m
Battery leads
• Quantity: 1 red and 1 black
• Length: 1.3 m
• Wire type: 0.5 mm2solid conductor
• Insulation rating: 90 °C
Battery end termination
Push on 4.8 mm receptacle to suit battery spade fitted with insulating cover
Module end termination
8.0 mm stripped insulation
Two-piece batteries are supplied with a 200 mm lead with 4.8 mm receptacle
at each end and insulting covers to connect the separate sticks together.
• Polycarbonat white/green
• Type of protection IP 20

www.tridonic.com 13
Subject to change without notice. Information provided without guarantee.
Data sheet 03/20-EM042-21
Emergency lighting units
EM powerLED
5. Electrical data
Automatic circuit breaker type C10 C13 C16 C20 B10 B13 B16 B20 Inrush current
Installation Ø1.5 mm21.5 mm22.5 mm22.5 mm21.5 mm21.5 mm22.5 mm22.5 mm2Imax time
EM powerLED BASIC FX 103 SR 50W 50V 20 30 40 50 16 24 32 40 6.6 A 30 μs
EM powerLED BASIC FX 104 SR 50W 50V 20 30 40 50 16 24 32 40 6.6 A 30 μs
Harmonic distortion in the mains supply (at 230 V / 50 Hz and full load) in %
Type THD 3 5 7
EM powerLED BASIC FX 103 SR 50W 50V 6.5 % 4.5 % 2 % 1 %
EM powerLED BASIC FX 104 SR 50W 50V 6.5 % 4.5 % 2 % 1 %
5.1 Maximum loading of automatic circuit breakers
5.2 Harmonic distortion in the mains supply (at 230 V / 50 Hz and full load) in %
5.3 Insulation matrix
Mains Switched Live C/F L link Battery, LED, Test
switch, Indicator LED I-SELECT 2
Mains – • • • • • •
Switched Live • – • • • • •
C/F • • – • • • •
L link • • • – • • •
Battery, LED, Test
switch, Indicator LED • • • • • • • • –• •
I-SELECT 2 •••• • • –
• Represents basic insulation
• • Represents double or reinforced insulation

www.tridonic.com 14
Subject to change without notice. Information provided without guarantee.
Data sheet 03/20-EM042-21
Emergency lighting units
EM powerLED
5.5 Output current setting
Output current can be set by connecting a resistor between the 2 “I set” termi-
nals. Relationship between output current and resistor value can be found at
the table “Specific technical data”. Resistor values specified from standardised
resistor value ranges.
Resistor value tolerance has to be ≤ 1 %.
Resistor power has to be ≥ 0.1 W.
Resistor detection at each start.
Change of the resistor value during the operation will be not considered.
Resistors for the main output current values can be ordered from Tridonic (see
accessories).
EM powerLED BASIC FX 103 SR 50W 50V – 3 cells
Article number: 89800430
3.6 V battery voltage
750 – 960 mA battery discharge current (tolerance)
EM powerLED BASIC FX 104 SR 50W 50V – 4 cells
Article number: 89800412
4.8 V battery voltage
750 – 960 mA battery discharge current (tolerance)
5.4 Typ. LED current/voltage characteristics
The LED current in emergency mode is automatically adjusted by the EM powerLED module based on the total forward voltage of
the LED modules connected and the associated battery.
Note: LED peak current is measured at the max. battery discharge current.
LED current at nominal battery voltage and
min. battery discharge current
LED current at nominal battery voltage and
max. battery discharge current
LED current [mA]
VLED [V] VLED [V]
LED current [mA]
50
400
350
300
250
200
150
100
10 2015 25 35 4530 40 50 5510
0
30
60
90
120
150
180
210
270
240
300
2015 25 35 4530 40 50 55
LED peak current at start in emergency mode – 3 cells
Voltage Inrush current Duration
46.0 V 209 mA 7.35 ms
43.5 V 218 mA 7.85 ms
41.0 V 229 mA 8.10 ms
38.5 V 241 mA 8.25 ms
36.0 V 255 mA 8.35 ms
33.5 V 270 mA 8.55 ms
31.0 V 288 mA 8.85 ms
28.5 V 307 mA 9.10 ms
26.0 V 330 mA 9.40 ms
23.0 V 354 mA 9.80 ms
20.5 V 383 mA 10.45 ms
18.0 V 417 mA 11.40 ms
15.5 V 455 mA 11.95 ms
13.0 V 500 mA 15.10 ms
LED peak current at start in emergency mode – 4 cells
Voltage Inrush current Duration
46.5 V 252 mA 8.65 ms
44.0 V 259 mA 9.30 ms
41.5 V 268 mA 8.10 ms
39.0 V 288 mA 8.45 ms
36.5 V 300 mA 9.45 ms
34.0 V 323 mA 9.60 ms
31.5 V 340 mA 9.95 ms
29.0 V 364 mA 10.85 ms
26.0 V 388 mA 11.60 ms
23.5 V 414 mA 12.40 ms
21.0 V 446 mA 13.35 ms
18.5 V 479 mA 15.20 ms
16.0 V 520 mA 16.90 ms
13.5 V 564 mA 18.95 ms

www.tridonic.com 15
Subject to change without notice. Information provided without guarantee.
Data sheet 03/20-EM042-21
Emergency lighting units
EM powerLED
6.1 Short-circuit behaviour
In case of a short circuit the unit switches to shut down mode. After elimina-
tion of the short circuit a mains reset (SL off/on) is necessary.
6.2 No-load operation or load loss during operation
LED Driver will detect a load loss during operation. In this case and no-load ope-
ration the max. output voltage can apply at the LED output for max. 5 s before
LED Driver shuts down. Mains reset is required to restart the LED Driver.
6.3 Overload protection
LED Driver will switch off at overload operation. Mains reset is required to
restart the LED Driver.
6.4 Underload operation
LED Driver will switch off at underload operation. Mains reset is required to
restart the LED Driver.
6.5 Forward voltage out of range
If the forward voltage is out of range the unit switches to shut down mode.
After elimination of the short circuit a mains reset (SL off/on) is necessary.
6. Functions
1 h
3 h
Without link
With link
Duration Usage duration link
6.6 Duration link selection
Note: LED Driver supplied with duration link in 3 hours position. Remove
duration link for 1 hour duration. Duration link and I-SELECT PLUG must be set
before battery and mains connection.

www.tridonic.com 16
Subject to change without notice. Information provided without guarantee.
Data sheet 03/20-EM042-21
Emergency lighting units
EM powerLED
7.1 Battery selection
7. Battery data
EM powerLED BASIC FX 50 W 50 V, 1 / 3 h
Type EM powerLED BASIC FX
103 SR 50W 50V
EM powerLED BASIC FX
104 SR 50W 50V
Article no. 89800430 89800412
Cells 3 cells 4 cells
Duration 1 h 3 h 1 h 3 h
Technology
and capacity
Design Number
of cells
Type Article no. Assignable batteries
NiCd 4 Ah
D cells
stick 1 x 3 Accu-NiCd 3A 55  •
stick 1 x 4 Accu-NiCd 4A 55  •
stick + stick 2 + 2 Accu-NiCd 4C 55  •
side by side 3 x 1 Accu-NiCd 3B 55  •
side by side 4 x 1 Accu-NiCd 4B 55  •
NiMH 2.2 Ah
Cs cells
stick 1 x 3 Accu-NiMH 3A  •
stick 1 x 4 Accu-NiMH 4A  •
NiMH 4 Ah
LA cells
stick 1 x 3 Accu-NiMH 4Ah 3A CON  •
stick 1 x 4 Accu-NiMH 4Ah 4A CON  •
stick + stick 2 + 2 Accu-NiMH 4Ah 4C CON  •
NiCd 1.8 Ah
Cs cells
remote box 1 x 3 Pack-NiCd 3C CON  •
remote box 1 x 4 Pack-NiCd 4C CON  •
NiCd 4.5 Ah
D cells
remote box 1 x 3 Pack-NiCd 3D CON  •
remote box 1 x 4 Pack-NiCd 4D CON  •
NiMH 2.2 Ah
Cs cells
remote box 1 x 3 Pack-NiMH 2.2Ah 3 CON  •
remote box 1 x 4 Pack-NiMH 2.2Ah 4 CON  •
NiMH 4 Ah
LAL cells
remote box 1 x 3 Pack-NiMH 4Ah 3 CON  •
remote box 1 x 4 Pack-NiMH 4Ah 4 CON  •

www.tridonic.com 17
Subject to change without notice. Information provided without guarantee.
Data sheet 03/20-EM042-21
Emergency lighting units
EM powerLED
7.6 Batteries
Connection method: 4.8 x 0.5 mm spade tag welded to end of cell
For stick packs this connection is accessible after the battery caps have been
fitted.
To inhibit inverter operation disconnect the batteries by removing the con-
nector from the battery spade tag.
For further information refer to corresponding battery datasheet.
7.7 Storage, installation and commissioning
Relevant information about storage conditions, installation and commissioning
are provided in the battery datasheets.
7.2 Accu-NiCd
4.2 / 4.5 Ah
Battery voltage/cell 1.2 V
Cell type D
Case temperature range
to ensure 4 years design life +5 °C to +55 °C
Max. short term temperature (reduced life-time) 70 °C
Max. number discharge cycles 12 cycles per year plus
4 cycles during
comissioning
Max. storage time 6 months
7.3 Accu-NiMh
2.2 Ah
Battery voltage/cell 1.2 V
Cell type Cs
Case temperature range
to ensure 4 years design life +5 °C to +50 °C
Max. short term temperature (reduced life-time) 70 °C
Max. number discharge cycles 4 cycles per year plus
30 cycles during
comissioning
Max. storage time 12 months
4.0 Ah
Battery voltage/cell 1.2 V
Cell type LA
Case temperature range
to ensure 4 years design life +5 °C to +45 °C
Max. short term temperature (reduced life-time) 70 °C
Max. number discharge cycles 4 cycles per year plus
30 cycles during
comissioning
Max. storage time 12 months
7.4 Accupack-NiCd
1.8 Ah
Battery voltage/cell 1.2 V
Cell type Cs
Ambient temperature range
to ensure 4 years design life +5 °C to +40 °C
tc point +45 °C
Max. short term temperature (reduced life-time) 70 °C
Max. number discharge cycles 4 cycles per year plus
4 cycles during
comissioning
Max. storage time 6 months
4.5 Ah
Battery voltage/cell 1.2 V
Cell type D
Ambient temperature range
to ensure 4 years design life +5 °C to +40 °C
tc point +45 °C
Max. short term temperature (reduced life-time) 70 °C
Max. number discharge cycles 4 cycles per year plus
4 cycles during
comissioning
Max. storage time 6 months
7.5 Accupack-NiMH
2.2 Ah
Battery voltage/cell 1.2 V
Cell type Cs
Ambient temperature range
to ensure 4 years design life +5 °C to +35 °C
tc point +40 °C
Max. short term temperature (reduced life-time) 70 °C
Max. number discharge cycles 4 cycles per year plus
4 cycles during
comissioning
Max. storage time 12 months
4.0 Ah
Battery voltage/cell 1.2 V
Cell type LAL
Ambient temperature range
to ensure 4 years design life +5 °C to +35 °C
tc point +40 °C
Max. short term temperature (reduced life-time) 70 °C
Max. number discharge cycles 4 cycles per year plus
4 cycles during
comissioning
Max. storage time 12 months
8. Miscellaneous
8.1 Maximum number of switching cycles
All LED Drivers are tested with 50,000 switching cycles.
The actually achieved number of switching cycles is significantly higher.
8.2 Additional information
Additional technical information at www.tridonic.com →Technical Data
Guarantee conditions at www.tridonic.com →Services
Life-time declarations are informative and represent no warranty claim.
No warranty if device was opened.