Tridonic BASIC Series User manual

www.tridonic.com 1
Subject to change without notice. Information provided without guarantee.
Data sheet 09/22-EM080-23
Emergency lighting units
EM converterLED
Product description
• Self contained emergency lighting LED driver for manual testing
• For LED modules with a forward voltage of 50 – 250 V
• Low profile casing (21 x 30 mm cross-section)
• For luminaire installation
• Nominal lifetime up to 100,000 h
• 5 years guarantee (conditions at www.tridonic.com)
Properties
• Non maintained operation
• 1 or 3 h rated duration
• Operating time selectable with plug (duration link)
• Compatible with all dimmable and non-dimmable constant
current LED driver (see chapter 5.4)
• 3-pole technology: 2-pole LED module changeover
and delayed power switching for the LED driver
• Automatic shutdown of output if LED load is out of range
• Constant power output
• Maximum light output for all LED modules
• Electronic charge system
• Deep discharge protection
• Short-circuit-proof battery connection
• Polarity reversal protection for battery provided by 3-pole
connector
• Automatic detection of the connected battery technology
(NiMH or LiFePO4batteries)
Batteries
• High-temperature cells
• NiMH or LiFePO4batteries
• LA or 18650 cells
• 4-year design life for NiMH batteries
• 1-year guarantee for NiMH batteries
• 4 – 8 years design life for LiFePO4batteries
• 3 years guarantee for LiFePO4batteries
• For battery compatibility refer to chapter 7.1
È
Standards, page 6
Wiring diagrams and installation examples, page 7
EM converterLED BASIC MH/LiFePO4 250 V
BASIC series

www.tridonic.com 2
Subject to change without notice. Information provided without guarantee.
Data sheet 09/22-EM080-23
Emergency lighting units
EM converterLED
Specific technical data
Type1Battery
technology
Rated
duration
Typ. λ (at 230
V, 50 Hz)
Typ. output
power
P emergency
Mains current in charging operation Rated power in charging operation
Initial charge Fast recharge Trickle charge3Initial charge Fast recharge Trickle charge3
EM converterLED BASIC
202A MH/LiFePO4 250V
NiMH 1 h 0.60C 2.3 W 17 mA 17 mA 17 / 12 mA 2.4 W 2.4 W 2.4 / 1.4 W
3 h 0.60C 2.3 W 18 mA 18 mA 18 / 12 mA 2.6 W 2.6 W 2.6 / 1.4 W
LiFePO4 1 h 0.60C 2.3 W 17 mA 17 mA 17 / 12 mA 2.1 W 2.1 W 2.1 / 1.4 W
3 h 0.60C 2.3 W 20 mA 20 mA 20 / 12 mA 2.9 W 2.9 W 2.9 / 1.4 W
EM converterLED BASIC
203 MH/LiFePO4 250V
NiMH 1h 0.60C 2.5 W 17 mA 17 mA 17 / 12 mA 2.4 W 2.4 W 2.4 / 1.4 W
3h 0.60C 2.5 W 19 mA 19 mA 19 / 12 mA 2.9 W 2.9 W 2.9 / 1.4 W
LiFePO4
1h 0.60C 2.5 W 20 mA 20 mA 20 / 12 mA 2.8 W 2.8 W 2.8 / 1.4 W
3h 0.60C 2.5 W 25 mA 25 mA 25 / 12 mA 3.9 W 3.9 W 3.9 / 1.4 W
EM converterLED BASIC
204 MH/LiFePO4 250V
NiMH 1h 0.65C 3.5 W 18 mA 18 mA 18 / 12 mA 2.5 W 2.5 W 2.5 / 1.4 W
3h 0.65C 3.5 W 21 mA 21 mA 21 / 12 mA 3.2 W 3.2 W 3.2 / 1.4 W
LiFePO4
1h 0.65C 3.5 W 20 mA 20 mA 20 / 12 mA 2.8 W 2.8 W 2.8 / 1.4 W
3h 0.65C 3.5 W 26 mA 26 mA 26 / 12 mA 3.9 W 3.9 W 3.9 / 1.4 W
EM converterLED BASIC
205 MH/LiFePO4 250V
NiMH 1h 0.65C 4.5 W 19 mA 19 mA 19 / 12 mA 2.7 W 2.7 W 2.7 / 1.4 W
3h 0.65C 4.5 W 22 mA 22 mA 22 / 12 mA 3.3 W 3.3 W 3.3 / 1.4 W
LiFePO4
1h 0.65C 4.5 W 20 mA 20 mA 20 / 12 mA 2.8 W 2.8 W 2.8 / 1.4 W
3h 0.65C 4.5 W 26 mA 26 mA 26 / 12 mA 3.9 W 3.9 W 3.9 / 1.4 W
1EM = Emergency
216 h battery charging time for 2 h emergency lighting function according to AS 2293.
3In case of NiMH batteries: Intermittent charge is used. Value 1 is for 4 min. charge on / Value 2 is for 16 min. charge o. In case of LiFePO4 batteries voltage dependent constant current charging is used.
412 h battery charging time for 2 h emergency lighting function when used with LiFePO4batteries.
EL
Technical data
Rated supply voltage 220 – 240 V
AC voltage range 198 – 264 V
Mains frequency 50 / 60 Hz
LED module forward voltage range 50 – 250 V
Output current see chapter 5.3
Time to light < 0.5 s from detection of emergency
event
Overvoltage protection 320 V (for 48 h)
U-OUT (including open- / short-circuit and
double load)
280 V
Max. open circuit voltage 280 V
Battery charging time 24 h24
Ambient temperature range ta -5 ... + 55 °C
Max. casing temperature tc 75 °C
Mains voltage changeover threshold according to EN 60598-2-22
Mains surge capability (between L – N) 1 kV
Mains surge capability (between L/N – PE) 2 kV
Type of protection IP20
Lifetime up to 100,000 h
Guarantee (conditions at www.tridonic.com) 5 years
Dimensions LxWxH 179 x 30 x 21 mm
EM converterLED BASIC MH/LiFePO4 250 V
BASIC series
30
21
30
179
169.2
Duration
link 3 h
No
duration
link 1 h
Note: LED driver supplied with duration link in 3 hours position. Remove duration link for
1 hour duration. Duration link must be set before battery and mains connection.
Ordering data
Type1Article
number
Rated
duration
Packaging,
carton
Packaging,
pallet
Weight
per pc.
EM converterLED BASIC 202A MH/LiFePO4 250V  1/3 h 10 pc(s). 1,600 pc(s). 0.07 kg
EM converterLED BASIC 203 MH/LiFePO4 250V  1/3 h 10 pc(s). 1,600 pc(s). 0.07 kg
EM converterLED BASIC 204 MH/LiFePO4 250V  1/3 h 10 pc(s). 1,600 pc(s). 0.07 kg
EM converterLED BASIC 205 MH/LiFePO4 250V  1/3 h 10 pc(s). 1,600 pc(s). 0.07 kg
EMcLED Strain-relief set 240x43x30mm
ACCES-
SORIES
43
6868
240
30
Permissible cable jacket diameter 2.2 – 9 mm
Ordering data
Type Article
number Packaging, carton Packaging, pallet Weight per pc.
EMcLED SR  10 pc(s). 1,260 pc(s). 0.08 kg

www.tridonic.com 3
Subject to change without notice. Information provided without guarantee.
Data sheet 09/22-EM080-23
Emergency lighting units
EM converterLED
EMcLED Strain-relief set 240x43x30mm
ACCES-
SORIES
43
6868
240
30
Permissible cable jacket diameter 2.2 – 9 mm
Ordering data
Type Article
number Packaging, carton Packaging, pallet Weight per pc.
EMcLED SR  10 pc(s). 1,260 pc(s). 0.08 kg
Product description
• Optional strain-relief set for independent applications
• Transforms the LED driver into a fully class II compatible LED
driver (e.g. ceiling installation)
• Easy and tool-free mounting to the LED driver, screwless cable-
clamp channels with strain-relief (240 x 43 x 30 mm)

www.tridonic.com 4
Subject to change without notice. Information provided without guarantee.
Data sheet 09/22-EM080-23
Emergency lighting units
EM converterLED
Product description
• A green LED indicates that charging current is flowing into the
battery
• Plug connection
Status indication green LED
ACCES-
SORIES
Ordering data
Type Article number Packaging,
bag
Packaging,
carton
Weight
per pc.
LED EM green, 1.0 m CON  25 pc(s). 200 pc(s). 0.015 kg
LED EM green, HO 1.0 m CON  25 pc(s). 200 pc(s). 0.015 kg
LED EM green, 0.6 m CON  25 pc(s). 200 pc(s). 0.009 kg
LED EM green, HO 0.6 m CON  25 pc(s). 200 pc(s). 0.009 kg
LED EM green, 0.3 m CON  25 pc(s). 200 pc(s). 0.005 kg
LED EM green, HO 0.3 m CON  25 pc(s). 200 pc(s). 0.005 kg
Test switch EM3
ACCES-
SORIES
Ordering data
Type Article number Packaging,
bag
Packaging,
carton
Weight
per pc.
Test switch EM 3  25 pc(s). 200 pc(s). 0.013 kg
Connection Cable NiMH
ACCES-
SORIES
Extension Cable LiFePO4
ACCES-
SORIES
Ordering data
Type Article number Packaging,
bag
Packaging,
carton
Weight
per pc.
EXTENSION CABLE LiFePO4 500mm  10 pc(s). 200 pc(s). 0.01 kg
Product description
• For connection to the emergency lighting unit
• For checking the device function
• Plug connection
• Dielectric strength: 1,500 V AC for 60 seconds

www.tridonic.com 5
Subject to change without notice. Information provided without guarantee.
Data sheet 09/22-EM080-23
Emergency lighting units
EM converterLED
Product description
• Connection cable for NiMH batteries
• Cable length 500 mm
• 2-pole plug connection for batteries and 3-pole plug connection
for LED driver
Connection Cable NiMH
ACCES-
SORIES
Ordering data
Type Article number Packaging,
bag
Packaging,
carton
Weight
per pc.
CONNECTION CABLE NiMH 500mm  10 pc(s). 200 pc(s). 0.015 kg
Product description
• Extension cable for LiFePO4batteries
• Cable length 500 mm
• 3-pole plug connection
Extension Cable LiFePO4
ACCES-
SORIES
Ordering data
Type Article number Packaging,
bag
Packaging,
carton
Weight
per pc.
EXTENSION CABLE LiFePO4 500mm  10 pc(s). 200 pc(s). 0.01 kg

www.tridonic.com 6
Subject to change without notice. Information provided without guarantee.
Data sheet 09/22-EM080-23
Emergency lighting units
EM converterLED
1. Standards
• EN 61347-1
• EN 61347-2-13
• EN 61347-2-7
• EN 55015
• EN 61000-3-2
• EN 61000-3-3
• EN 61547
• EN 60068-2-64
• EN 60068-2-29
• EN 60068-2-30
• EN 62384
• according to EN 50172
• according to EN 60598-2-22
1.1 Glow-wire test
according to EN 61347-1 with increased temperature of 850 °C passed.
1.2 Insulation and electric strength testing of luminaires
Electronic LED-drivers can be damaged by high voltage. This has to be consid-
ered during the routine testing of the luminaires in production.
According to IEC 60598-1 Annex Q (informative only!) or ENEC 303-Annex A,
each luminaire should be submitted to an insulation test with 500VDC for 1 sec-
ond. This test voltage should be connected between the interconnected phase
and neutral terminals and the earth terminal. The insulation resistance must be
at least 2 MΩ.
As an alternative, IEC 60598-1 Annex Q describes a test of the electrical
strength with 1,500 VAC (or 1,414 x 1,500 VDC). To avoid damage to the electronic
devices this test must not be conducted.
2. Thermal details and lifetime
2.1 Lifetime
Average lifetime 50,000 hours under rated conditions with a failure rate of
less than 10 %. Average failure rate of 0.2 % per 1000 operating hours.
Expected lifetime with NiMH batteries
EM converterLED BASIC 202A
MH/LiFePO4 250V
tc 65°C 70°C 75°C
lifetime > 100,000 h > 100,000 h 94,000 h
EM converterLED BASIC 203
MH/LiFePO4 250V
tc 65 °C 70 °C 75 °C
lifetime > 100,000 h > 100,000 h 87,000 h
EM converterLED BASIC 204
MH/LiFePO4 250V
tc 65 °C 70 °C 75 °C
lifetime > 100,000 h > 100,000 h 84,000 h
EM converterLED BASIC 205
MH/LiFePO4 250V
tc 65 °C 70 °C 75 °C
lifetime > 100,000 h > 100,000 h 80,000 h
Expected lifetime with LiFePO4batteries
EM converterLED BASIC 202A
MH/LiFePO4 250V
tc 65°C 70°C 75°C
lifetime > 100,000 h > 100,000 h 97,000 h
EM converterLED BASIC 203
MH/LiFePO4 250V
tc 65 °C 70 °C 75 °C
lifetime > 100,000 h > 100,000 h 82,000 h
EM converterLED BASIC 204
MH/LiFePO4 250V
tc 65 °C 70 °C 75 °C
lifetime > 100,000 h > 100,000 h 82,000 h
EM converterLED BASIC 205
MH/LiFePO4 250V
tc 65 °C 70 °C 75 °C
lifetime > 100,000 h > 100,000 h 81,000 h
3. Installation / Wiring
3.1 Wiring diagram
One or more LED modules with a total forward voltage of 50 to 250 V can be
connected to the EM converterLED 250V module. These LED module(s), marked
with “Emergency” are operated in emergency mode from the associated battery.
In normal mains mode all LED modules are operated by the LED driver from the
mains supply.
Use of the test switch:
For checking the device function press the test switch for a minimum of 3
seconds.
Meaning of marking
Double or reinforced insulation for built-in electronic LED drivers. The control
gear relies upon the luminaire enclosure for protection against accidental contact
with live parts.
The emergency lighting LED driver is designed for a lifetime stated above under
reference conditions and with a failure probability of less than 10 %.
The relation of tc to ta temperature depends also on the luminaire design.
If the measured tc temperature is approx. 5 K below tc max., ta tempera-
ture should be checked and eventually critical components (e.g. ELCAP)
measured. Detailed information on request.

www.tridonic.com 7
Subject to change without notice. Information provided without guarantee.
Data sheet 09/22-EM080-23
Emergency lighting units
EM converterLED
EM converterLED BASIC with a standard LED driver and one LED module for mains and emergency operation
Neutral
+
+
–
–
–
+
P
O
Lout
Lin
N
L
L
N
Neutral
Un-Switched Line
Test
switch
Indicator
LED
Switched Line in
Switched Line out
LED driver
LED
LED
LED driver LED Module
Emergency
–
+
LED driver
max. 150 W in operation
EM converterLED
BASIC
Battery
Battery
EM converterLED BASIC with one LED module for non-maintained emergency operation
+
+
–
–
–
+
P
O
Lout
Lin
N
L
EM converterLED
BASIC
Neutral
Un-Switched Line
Test
switch
Indicator
LED
Not connected
Not connectedLED driver
LED
LED
LED driver
Battery
Battery
LED Module
Emergency
EM converterLED BASIC with a standard LED driver and series operation of LED modules
One LED module is operated in emergency mode.
All LED modules are operated in mains mode.
Neutral
+
+
–
–
–
+
P
O
Lout
Lin
N
L
L
N
Neutral
Un-Switched Line
Test
switch
Indicator
LED
Switched Line in
Switched Line out LED driver
LED
LED
LED driver LED Module
Emergency
–
+
–
+
LED Module
–
+
LED Module
LED driver
max. 150 W in operation
EM converterLED
BASIC
Battery
Battery

www.tridonic.com 8
Subject to change without notice. Information provided without guarantee.
Data sheet 09/22-EM080-23
Emergency lighting units
EM converterLED
EM converterLED BASIC with a standard LED driver and parallel operation of LED modules
Neutral
+
+
–
–
–
+
P
O
Lout
Lin
N
L
L
N
Neutral
Un-Switched Line
Test
switch
Indicator
LED
LED driver
LED
LED
LED driver LED Module
Emergency
–
+
–
+
LED Module
–
+
LED Module
LED driver
max. 150 W in operation
Switched Line in
Switched Line out
EM converterLED
BASIC
Battery
Battery
One LED module is operated in emergency mode.
All LED modules are operated in mains mode.
8 – 9 mm
wire preparation:
0.5 – 1.5 mm²
3.2 Wiring type and cross section
Solid wire with a cross section of 0.5 – 1.5 mm². Strip 8 – 9 mm of insulation
from the cables to ensure perfect operation of terminals.
Wiring: LED module/LED driver/supply
3.3 Battery connection
LiFePO4: Direct connection
NiMH: Connection with extension
When using an EM converterLED in combination with a NiMH battery, order the
CONNECTION CABLE NiMH 500mm seperately.
LiFePO4: Connection with extension
Battery
300
EM converterLED
Battery
500
300
EM converterLED
Battery
500
300
EM converterLED

www.tridonic.com 9
Subject to change without notice. Information provided without guarantee.
Data sheet 09/22-EM080-23
Emergency lighting units
EM converterLED
4. Mechanical values
4.1 Housing properties
• Casing manufactured from polycarbonate.
• Type of protection: IP20
• Max. torque at the mounting screws: 0.8 Nm
4.2 Mechanical data accessories
LED status indicator
• Green
• Mounting hole 6.5 mm diameter, 1 – 1.6 mm thickness
• Lead length 0.3 m / 0.6 m / 1.0 m
• Insulation rating: 90 °C
• Plug connection
Test switch
• Mounting hole 7.0 mm diameter
• Lead length 0.55 m
• Plug connection
Battery connection
• Plug connection 0.3 m
• Extension 0.5 m
3.6 Maximum lead length
LED 3 m (6 m loop)1
Status indication LED 1 m
Batteries 0.8 m
3.7 Use of different phases
The use of different phases for switched line and unswitched line is allowed.
When using different phases, the unswitched line must fail if the switched
line fails. This is required to assure correct switching into emergency mode. It
can be realised with a relay.
3.4 Loose wiring
Loosen wire through twisting
and pulling or using a Ø1 mm
release tool
3.5 Wiring guidelines
• The output to the LED is DC but has high frequency content, which should be
considered for good EMC compliance.
• Separate LED leads from the mains and DALI connections and wiring for good
EMC performance.
• Maximum lead length on the LED terminals is 3 m. For a good EMC
performance keep the LED wiring as short as possible.
• Route the secondary wires (LED module) in parallel to ensure good EMC
performance.
• Maximum lead length for the Test switch and Indicator LED connection is
1 m. Separate the test switch and Indicator LED wiring from the LED leads to
prevent noise coupling.
• Battery leads are specified with 0.5 mm cross section and a length of 0.8 m
• Protect the wiring against short circuits to earth (sharp edged metal parts,
metal cable clips, louver, etc.) to avoid the damage of the control gear.
To ensure that a luminaire containing LED emergency units complies with
EN 55015 for radio frequency conducted interference in both normal and
emergency mode it is essential to follow good practice in the wiring layout.
Within the luminaire route the switched and unswitched 50 Hz supply wiring
as short as possible and keep it as far away as possible from the LED leads.
Through wiring may affect the EMC performance of the luminaire.
Do not exceed the max. length of LED leads to the LED module. Note that the
length of the EM converterLED leads to the LED module is added to the length
of the leads from the LED driver to the EM converterLED module when conside-
ring the max. permitted lead length of the LED driver.
1Note: The length of LED leads to the LED module must not be exceeded. Note that the length
of the EM converterLED leads is added to the length of the leads from the LED driver to the EM
converterLED module when considering max. permitted lead length of the LED driver. Leads
should always be kept as short as possible.
5. Electrical values
5.1 Maximum loading of automatic circuit breakers
Automatic circuit breaker type B10 B13 B16 B20 C10 C13 C16 C20 Inrush current
Installation Ø1.5 mm21.5 mm21.5 mm22.5 mm21.5 mm21.5 mm21.5 mm22.5 mm2Imax time
EM converterLED BASIC MH/LiFePO4 250V 90 130 130 130 180 260 260 260 10 A 120 μs
5.2 Insulation matrix
When using a non-SELV LED driver insulate the
battery, LED, test switch and indicator LED in the
luminaire according to the U-OUT rating of the
LED driver.
Mains Switched Live Battery, LED, Test
switch, Indicator LED LED driver
Mains – • • • •
Switched Live • – • • •
Battery, LED, Test
switch, Indicator LED • • • • – –
LED driver • • – –
• Represents basic insulation
• • Represents double or reinforced insulation

www.tridonic.com 10
Subject to change without notice. Information provided without guarantee.
Data sheet 09/22-EM080-23
Emergency lighting units
EM converterLED
LED current at nominal battery voltage and
min. battery discharge current
LED current at nominal battery voltage and
max. battery discharge current
5.3 Typ. LED current/voltage characteristics
The LED current in emergency mode is automatically adjusted by the EM converterLED module based on the total forward voltage of the LED modules con-
nected and the associated battery. The start of the LED in emergency mode does not result in a current peak.
EM converterLED BASIC 203 MH/LiFePO4 250V
Article number: 89800592
NiMH batteries, 3,6 V battery voltage
840 – 900 mA battery discharge current (tolerance)
LiFePO4batteries, 3,2 V battery voltage
955 – 1025 mA battery discharge current (tolerance)
EM converterLED BASIC 202A MH/LiFePO4 250V
Article number: 89800709
NiMH batteries, 3,6 V battery voltage
780 – 840 mA battery discharge current (tolerance)
LiFePO4batteries, 3,2 V battery voltage
830 – 950 mA battery discharge current (tolerance)
VLED [V]VLED [V]
LED current [mA] LED current [mA]
EM converterLED BASIC 204 MH/LiFePO4 250V
Article number: 89800581
NiMH batteries, 4,8 V battery voltage
850 – 910 mA battery discharge current (tolerance)
LiFePO4batteries, 3,2 V battery voltage
1350 – 1450 mA battery discharge current (tolerance)
LED current [mA]
VLED [V]
50 100 150 200 250
15
25
35
5
45
55
50 100 150 200 250
15
25
35
5
45
55
50 100 150 200 250
20
30
40
50
60
70
80
10
EM converterLED BASIC 205 MH/LiFePO4 250V
Article number: 89800582
NiMH batteries, 6,0 V battery voltage
860 – 920 mA battery discharge current (tolerance)
LiFePO4batteries, 3,2 V battery voltage
1770 – 1900 mA battery discharge current (tolerance)
LED current [mA]
VLED [V]
250
20
30
40
50
60
70
80
90
10
100
50 100 150 200

www.tridonic.com 11
Subject to change without notice. Information provided without guarantee.
Data sheet 09/22-EM080-23
Emergency lighting units
EM converterLED
5.4 LED driver compatibility
The EM converterLED emergency unit use 3 pole technology and is compa-
tible with most LED drivers on the market, however it is important to check
that the rating of the LED driver does not exceed the values specified below:
• The max. allowed output current rating of the associated LED driver is
2 A eff (current rating of the terminals of EM converterLED) and 2.4 A
peak (current rating of switching relays of EM converterLED)
• The max. allowed inrush current rating of the associated LED driver is
60 A peak for 1 ms or 84 A for 255 μs (inrush current rating of switching
relay of EM converterLED)
• The max. allowed output voltage (U-OUT) of the associated LED driver
applied to the EM converterLED output is 450 V (voltage withstand
between adjacent contact of the single switching relay of the
EM converterLED)
• The max. allowed LED load of the associated LED driver is 150 W in
operation. The load must be an LED module.
Check compatibility with short function tests (duration of several seconds).
6. Functions
6.1 Duration link selection
1 h
3 h
Without link
With link
Duration Usage duration link
Emergency lighting LED driver supplied with duration link in 3 hours
position.
The position of the link will only be read on first power up. If it is changed
afterwards both the battery and mains supply must be disconnected for
10 seconds to enable the EM converterLED to read the new link position on
reconnection of the battery and mains. It will lead to a false battery failure
indication if the link is changed after installation without this reset.

www.tridonic.com 12
Subject to change without notice. Information provided without guarantee.
Data sheet 09/22-EM080-23
Emergency lighting units
EM converterLED
7. Battery data
7.1 Battery selection
EM converterLED BASIC, 1 / 3 h, NiMH
Type EM converterLED BASIC 202A MH/
LiFePO4 250V
EM converterLED BASIC 203 MH/
LiFePO4 250V
EM converterLED BASIC 204 MH/
LiFePO4 250V
EM converterLED BASIC 205 MH/
LiFePO4 250V
Article no. 89800709 89800592 89800581 89800582
Duration 1 h 3 h 1 h 3 h 1 h 3 h 1 h 3 h
Battery charge
time
Initial charge 24 h
Fast recharge 24 h
Trickle charge continuously
Charging current
Initial charge 110 – 150 mA 190 – 230 mA 110 – 150 mA 190 – 230 mA 110 – 150 mA 190 – 230 mA 110 – 150 mA 190 – 230 mA
Fast recharge 110 – 150 mA 190 – 230 mA 110 – 150 mA 190 – 230 mA 110 – 150 mA 190 – 230 mA 110 – 150 mA 190 – 230 mA
Trickle charge
110 – 150 mA /
4 min.
0 mA / 16 min.
190 – 230 mA /
4 min.
0 mA / 16 min.
110 – 150 mA /
4 min.
0 mA / 16 min.
190 – 230 mA /
4 min.
0 mA / 16 min.
110 – 150 mA /
4 min.
0 mA / 16 min.
190 – 230 mA /
4 min.
0 mA / 16 min.
110 – 150 mA /
4 min.
0 mA / 16 min.
190 – 230 mA /
4 min.
0 mA / 16 min.
Discharge current 780 – 840 mA 780 – 840 mA 840 – 900 mA 840 – 900 mA 850 – 910 mA 850 – 910 mA 860 – 920 mA 860 – 920 mA
Charge voltage range10.9 – 1.65 V per cell
Discharge voltage range 1.65 – 1.05 V per cell
1The battery will be charged below 0.9 V. The EM converterLED will indicate a battery fault.
The emergency lighting LED driver will recharge the battery normally after running the test of 61347-2-7 CL 22.3 (abnormal operating conditions).
7.2 Battery charge / discharge data
EM converterLED BASIC, 1 / 3 h
Type EM converterLED BASIC
202A MH/LiFePO4 250V
EM converterLED BASIC
203 MH/LiFePO4 250V
EM converterLED BASIC
204 MH/LiFePO4 250V
EM converterLED BASIC
205 MH/LiFePO4 250V
Article no. 89800709 89800592 89800581 89800582
Duration 1 h 3 h 1 h 3 h 1 h 3 h 1 h 3 h
Technology
and capacity
Design Number
of cells
Type Article no. Assignable batteries
NiMH 4 Ah
LA cells
stick 1 x 3 Accu-NiMH 4Ah 3A CON  • •
stick 1 x 4 Accu-NiMH 4Ah 4A CON  •
stick + stick 2 + 2 Accu-NiMH 4Ah 4C CON  •
stick + stick 2 + 3 Accu-NiMH 4Ah 5C CON  •
remote box 1 x 3 Pack-NiMH 4Ah 3 CON  • •
remote box 1 x 4 Pack-NiMH 4Ah 4 CON  •
LiFePO4
1.5 Ah
18650 cells
stick 1 x 1 Accu-LiFePO4 1A CON  •
stick 1 x 2 Accu-LiFePO4 2A CON  •••
stick 1 x 3 Accu-LiFePO4 3A CON  •
stick 1 x 4 Accu-LiFePO4 4A CON  •
stick 1 x 5 Accu-LiFePO4 5A CON  •
stick 1 x 6 Accu-LiFePO4 6A CON  •
stick + stick 2 + 2 Accu-LiFePO4 4C CON  •
stick + stick 2 + 3 Accu-LiFePO4 5C CON  •
stick + stick 3 + 3 Accu-LiFePO4 6C CON  •
side by side 2 x 1 Accu-LiFePO4 2B CON  •••
side by side 3 x 1 Accu-LiFePO4 3B CON  •
side by side 4 x 1 Accu-LiFePO4 4B CON  •
side by side 5 x 1 Accu-LiFePO4 5B CON  •
side by side 6 x 1 Accu-LiFePO4 6B CON  •
remote box 1 x 1 PACK-LiFePO4 1.5Ah 1 CON  •
remote box 1 x 2 PACK-LiFePO4 3.0Ah 2 CON  •••
remote box 1 x 3 PACK-LiFePO4 4.5Ah 3 CON  •
remote box 1 x 4 PACK-LiFePO4 6.0Ah 4 CON  •

www.tridonic.com 13
Subject to change without notice. Information provided without guarantee.
Data sheet 09/22-EM080-23
Emergency lighting units
EM converterLED
EM converterLED BASIC, 1 / 3 h, LiFePO4
Type EM converterLED BASIC 202A MH/
LiFePO4 250V
EM converterLED BASIC 203 MH/
LiFePO4 250V
EM converterLED BASIC 204 MH/
LiFePO4 250V
EM converterLED BASIC 205 MH/
LiFePO4 250V
Article no. 89800709 89800592 89800581 89800582
Duration 1 h 3 h 1 h 3 h 1 h 3 h 1 h 3 h
Battery charge
time
Initial charge 24 h
Fast recharge 24 h
Trickle charge continuously and battery voltage controlled
Charging current
Initial charge 115 – 155 mA 250 – 290 mA 250 – 290 mA 430 – 470 mA 250 – 290 mA 430 – 470 mA 250 – 290 mA 430 – 470 mA
Fast recharge 115 – 155 mA 250 – 290 mA 250 – 290 mA 430 – 470 mA 250 – 290 mA 430 – 470 mA 250 – 290 mA 430 – 470 mA
Trickle charge1115 – 155 mA /
0 mA
250 – 290 mA /
0 mA
250 – 290 mA /
0 mA
430 – 470 mA /
0 mA
250 – 290 mA /
0 mA
430 – 470 mA /
0 mA
250 – 290 mA /
0 mA
430 – 470 mA /
0 mA
Discharge current 830 – 950 mA 830 – 950 mA 955 – 1,025 mA 955 – 1,025 mA 1,350 – 1,430 mA 1,350 – 1,430 mA 1,770 – 1,900 mA 1,770 – 1,900 mA
Charge voltage range22.0 – 3.65 V
Discharge voltage range 3.65 – 2.60 V
1Automatic recharge when battery voltage falls below 3.4 V. Charger o (0 mA) when battery voltage exceeds 3.6 V.
Note: Battery protected against operation at excessive temperatures (charging stopped when battery cell temperature < -5 °C or > 60 °C).
The emergency lighting LED driver will recharge the battery normally after running the test of 61347-2-7 CL 22.3 (abnormal operating conditions).
2The battery will not be charged below 2.0 V.
7.3 Accu-NiMH
Capacity 4.0 Ah
International designation HRMU 19/90
Battery voltage/cell 1.2 V
Cell type LA
Case temperature range
to ensure 4 years design life +5 °C to +50 °C
Max. short term battery case temperature
(shorter than 1 month over the battery lifetime) 70 °C
Max. number discharge cycles 4 cycles per year plus
30 cycles during
comissioning
Max. storage time 12 months
at +5 °C to +25 °C
7.4 Accu-LiFePO4
Capacity 1.5 Ah
International designation lFpR 19/66
Battery voltage/cell 3.2 V
Cell type 18650
Case temperature range to ensure
4 years design life +5 °C to +55 °C
6 years design life +5 °C to +45 °C
8 years design life +5 °C to +35 °C
Max. short term battery case temperature
(shorter than 1 month over the battery lifetime) 70 °C
Max. number discharge cycles 50 cycles total
Max. storage time 12 months
at +5 °C to +25 °C
7.5 Accupack-NiMH
Capacity 4.0 Ah
Battery voltage/cell 1.2 V
Cell type LAL
Ambient temperature range
to ensure 4 years design life +5 °C to +35 °C
tc point +40 °C
Max. short term battery case temperature
(shorter than 1 month over the battery lifetime) 70 °C
Max. number discharge cycles 4 cycles per year plus
4 cycles during
comissioning
Max. storage time 12 months
7.6 Accupack-LiFePO4
Capacity 1.5 Ah
International designation lFpR 19/66
Battery voltage/cell 3.2 V
Cell type 18650
Case temperature range to ensure
4 years design life +5 °C to +45 °C
6 years design life +5 °C to +35 °C
8 years design life +5 °C to +25 °C
Max. short term battery case temperature
(shorter than 1 month over the battery lifetime) 70 °C
Max. number discharge cycles 50 cycles total
Max. storage time 12 months
at +5 °C to +25 °C
Only use Tridonic batteries.
Comply with UN 38.3 and IEC 62133 (safety testing) protected against over
charge, over discharge, charging at excessive temperatures, short-circuit and
over current.

www.tridonic.com 14
Subject to change without notice. Information provided without guarantee.
Data sheet 09/22-EM080-23
Emergency lighting units
EM converterLED
8. Miscellaneous
8.1 Maximum number of switching cycles
EM converterLEDs are tested with 50,000 mains switching cycles of the
associated LED driver.
8.2 Battery replacement
After a battery replacement and a subsequent full charge cycle (24 h) a
duration test is mandatory to prove that with the new battery the rated
duration is achieved.
8.3 Mains-connected transformers
The EM converterLED does not contain mains-connected windings of trans-
formers.
8.4 Additional information
Additional technical information at www.tridonic.com →Technical Data
Lifetime declarations are informative and represent no warranty claim.
No warranty if device was opened.
7.9 Storage, installation and commissioning
Relevant information about storage conditions, installation and commissioning
are provided in the battery datasheets.
7.8 Wiring batteries
To inhibit inverter operation disconnect the batteries by removing the
connection at battery side.
For further informations refer to corresponding battery datasheet.
7.7 Safety
7.7.1 Deep discharge protection
When the battery remains connected without charging for a long period of time
after the battery cut off of the driver the battery voltage can still drop. To make
sure the cells are not damaged by this voltage drop, the battery protection
prevents the battery from further discharge below 2.0 V.
7.7.2 Overcharge protection
If in case of an error or the use of a wrong driver the battery gets overcharged
the battery protection will disconnect the battery from the driver at a voltage of
3.9 V. A discharge of the battery is still possible after the protection circuit was
triggered to guarantee emergency operation.
7.7.3 Short-circuit protection
In case of a short circuit the battery protection opens the connection to the
driver and the output is therefore free of voltage. The output will be reactivated
again when the short circuit is removed.
7.7.4 Overtemperature protection
The battery is protected against temporary thermal overheating. If the tempera-
ture limit is exceeded the further charging of the battery is no longer possible.
The temperature protection is activated below approx. 0 °C and above approx.
+60 °C. The discharging of the battery is still possible to guarantee emergency
operation.