Trimco UHF 212 User manual

INSTALLATION GUIDE# 22026
TRIANGLE BRASS MANUFACTURING
1351 ROCKY POINT DRIVE
OCEANSIDE, CA 92056
WWW.TRIMCOHARDWARE.COM
[email protected]
323.262.4191
PARTS LIST
STEP 2
FOLLOW THE INSTRUCTIONS BELOW FOR STEP BY STEP INSTALLATION.
SCAN QR CODE FOR INSTALLATION VIDEO. FOR INSTALLATION HELP,
PLEASE CONTACT TRIMCO CUSTOMER SERVICE.
*NOT TO SCALE*. IF ANY PARTS ARE MISSING,
PLEASE CONTACT TRIMCO CUSTOMER SERVICE.
PAGE 1 OF 2
DATE: 10/07/2021 REV: 02
INSTALL INTERIOR INDICATOR DECALS:
ADHESIVE IS ON THE GRAPHIC SIDE OF DECAL,
AND MUST BE INSTALLED ON THE BACK OF THE
INTERIOR ASSEMBLY TO BE VISIBLE THROUGH
THE INDICATOR WINDOWS.
D.
E.
F. G.
H.
I. J.
K.
C.
M.
L.
BOX 1 ITEMS
(A) 1X INTERIOR ASSEMBLY
(B ) 1X EXTERIOR PULL
REMOVE ALL EXISTING DOOR HARDWARE
INCLUDING THE DEADBOLT IF NEEDED.
INTERIOR SIDE:
INSERT CARRIER AS SHOWN. INSERT BOLT INTO CARRIER
NOTE: HOLES INDICATE
FOR 2 3/4 OR 2 3/8 DOOR WIDTH
SEE STEP 2
TOOLS
TOOLS BELOW MAY BE REQUIRED. TOOLS NOT INCLUDED.
•
CROSSHEAD SCREW DRIVER •PILOT HOLE DRILL (SIZE 3/32)
PARTS
STEP 1
Always refer to WWW.TRIMCOHARDWARE.COM for the latest documentation
LOCK UNLOCK
OVERVIEW UHF 212 (OUTSWING VERSION)
HANDS FREE SLIDE LOCK INSTALLATIONGUIDE
(C) 1X EXTERIOR MACHINE SCREWS, 10-24 X 3/4
(D) 1X CARRIER
(E) 1X LOCKING BOLT
(F) 1 X LATCH FACE AND SCREWS
(G) 1X DOOR STRIKE AND SCREWS
(H) 16X INTERIOR AND EXTERIOR PLATE WOOD/SHEETMETAL SCREWS
(I) 1X INDICATOR WITH OPEN & CLOSE STICKERS
(J) 1X INTERIOR OPEN AND CLOSE STICKERS
(K) 1X EMERGENCY O PEN TOOL
(L) 1X HH SIGN STICKER (FOR HEALTHY HARDWARE ONLY)
(M) 1X HANDS FREE STICKER
PRO TIP:
DEPENDING ON DOOR
HANDING, CHECK TO SEE
THAT THE LOCKED DECAL
IS SHOWN THROUGH THE
CORRECT INDICATOR
WINDOW BY SLIDING THE
BOLT TO THE LOCKED
POSITION. IF INCORRECT,
SWITCH DECALS.
PRO TIP:
NEW INSTALLATIONS FOLLOW ANSI 161 CYLINDRICAL DOOR PREPERATION.
RETROFIT COMPATIBILITY TO ANSI 161 CYLINDRICAL DOOR PREPERATION.
NOTE: ONLY COMPATIBLE WITH 1-3/4" THICK DOORS.
B.
A.

STEP 4
STEP 3
STEP 5
STEP 6
INSTALL INTERIOR ASSEMBLY
MOUNTING SCREWS AND
LATCH FACE.
INSTALL EXTERIOR PULL
DOOR SCREWS.
USE LEVEL OR MEASURE FROM
DOOR EDGE TO ALIGN INTERIOR
ASSEMBLY AND EXTERIOR PULL.
DOOR
EDGE
INSTALL INDICATOR WITH LEFT OR
RIGHT DECAL, DEPENDING ON
DOOR HANDING.
INSTALL EXTERIOR PULL
LOOSELY TO INTERIOR
ASSEMBLY STUDS. (DO NOT
TIGHTEN UNTIL PLATES ARE
ALIGNED TO DOOR).
INSTALL INTERIOR ASSEMBLY
(STUDS THROUGH CARRIER).
CHOOSE THE CORRECT DECAL
LEFT AND RIGHT HANDED
DECALS ARE PROVIDED.
PRO TIP: USE TAPE TO HOLD
ASSEMBLY IN PLACE WHILE THE
EXTERIOR IS BEING INSTALLED.
PRO TIP:
TO INSURE PROPER FUNTION LATCH PLATE
AND STRIKE MUST BE PROPERLY ALIGNED.
PRO TIP:
EXTEND LATCH BOLT WHEN TIGHENING
OUTER PLATES TO DOOR SURFACE. THIS
HELPS INSURE ALIGNMENT.
INSTALLATION GUIDE# 22026
PAGE 2 OF 2
DATE: 10/07/2021 REV: 02
Always refer to WWW.TRIMCOHARDWARE.COM for the latest documentation