Kaadas KA210 User manual

KA210
Smart Key-Free
Touchscreen Lock
Installation Guide / Quick Start Guide
Thank you for purchasing our products. Please review this manual thoroughly before operating your device.
All pictures in this manual are for illustration purpose only. Actual product may vary due to product upgrade.


Quick Start Guide
P 9
P 10
P 11
P12
P 13
P14
P16
P17
P18
P19
At a Glance
How to Lock/Unlock
Definitions
Code Format
Z-WaveTM Module installation and user guide
Quick Set Up
Factory Default Settings
Download Kaadas Home App
Troubleshooting
FCC Statement & Warnings
IMPORTANT:
Do not load batteries until the lock
is completely installed.
Installation Guide
STEP 1: Prepare the door and check dimensions
STEP 2: Install the latch and strike
STEP 3: Install exterior assembly
STEP 4: Install interior assembly
STEP 5: Insert batteries to calibrate the lock
handing process
P 3
P 4
P 6
P 7
P8
Do not use an electronic
scewdriver or drill during
installation.

INSTALLATION GUIDE
1
Latch (B)
Latch Screws
(J)
Interior
Assembly (D)
Exterior Assembly
(A)
Interior Assembly
Screws (F)
Battery
Cover (E)
Mounting Plate
Screws (G)
Strike Plate (H)
Reinforcement
Plate (H-1) (Optional)
Strike Plate
Screws (I)
Mounting
Plate (C)

Parts List
Mounting Plate x1
Exterior Assembly x1
Battery Cover x1
A B C
E F G
Latch Screws x2
J
Mounting Plate Screws x4
Latch x1
Drive-In Collar (Optional)
L
Z-Wave Module
(Optional)
MAA Battery x4
N
H-1
⅜
¾
2 2
Interior Assembly
Screws x3
Reset Tool
K
Interior Assembly x1
Strike Plate Screws x4
I
D
Reinforcement
Plate x1
(optional)
Strike Plate x1
H
(35mm<door thickness<43mm)
(43mm<door thickness<50mm)
2

Measure to confirm
that the backset is
either 2-3/8" or
2-3/4" (60 or 70mm)
2-3/8" or 2-3/4"
(60 or 70mm)
Make sure the hole in
the door frame is
drilled a minimum of 1’’
(25mm) deep, to leave
enough space for the
deadbolt to extend into
the door frame when
the door is locked.
AB
CD
Prepare the door and check dimensions
1
STEP
1"
25mm
1-3/8" to 2"
(35mm to 50mm)
Make sure the door frame is aligned with the door and there are
no obstructions stuck in the door frame.
Notes:
Measure to confirm
that the hole in the
door edge is 1"
(25mm).
Measure to confirm
that the door is 1-3/8"
to 2" (35mm to
50mm) thick.
Measure to
confirm that the
bore hole is
1-1/2’’ or 2-1/8"
(38mm or 54mm).
1-1/2" or 2-1/8"
(38 or 54mm) 1"
25mm
3

Drive-In Collar
(L)
Install the latch and strike
2
STEP
Hold the latch in front of the bore hole,
with the latch face flush against the
door edge. Is the slotted hole centered
in the door hole?
No adjustment is required.
Proceed to next step.
Slotted hole is
NOT centered.
A
B
YES
NO
Rotate and pull the
latch as shown to
extend latch.
2-3/4"
(70mm)
2-3/8"
(60mm)
pull
Install the latch.
Latch Screws (J)
up
Determine backset
and adjust the latch.
Chiseled
Not Chiseled
4

Make sure the hole in door frame is
drilled a minimum of 1" (25mm)
deep.
IMPORTANT:
I
H
H-1
(Optional)
C
Use a screwdriver to test if
deadbolt works smoothly.
D
Install strike on the door frame.
5

Mounting plate
Screws (G)
Install exterior assembly
3
STEP
Unlocked
IMPORTANT:
Locked
B
With the latch bolt fully
retracted (in the
unlocked position),
route the cable from
the exterior keypad
assembly below the
latch.
Remove the fire cup
Note:Remove the fire cup
may impact fire rating
Proceed to next step
A1-1/2" (38mm)
2-1/8" (54mm)
Measure the diameter of
the hole in the door.
1-1/2" or 2-1/8"
(38 or 54mm)
C
Secure the mounting
plate with the supplied
screws. Do not
overtighten screws.
Keep parallel to
door edge.
Before installation, make sure the latch is fully
retracted (in the unlocked position).
6

7
C
Install interior assembly
4
STEP
Insert the cable
into the connector.
Push the
connector in firmly
until it is
completely
attached.
A B
D
Interior Assembly
Screws (F)
E
Keep the thumb turn in the vertical position
and install the interior assembly.
Attach interior
assembly to
mounting plate and
tighten 3 screws.
The thumbturn can
be moved slightly
to facilitate the
installation of the
third screw.
Insert the Z-Wave
module and make
sure the network
Module is securely
plugged in.
Note:Before
inserting the
module, make sure
the lock does not
have a battery
installed.
Push the battery
cover up in the
direction as
illustrated. Horizontal
Z-Wave
Module
(Optional)

This step is required and crucial for the lock
after installation.
IMPORTANT:
8
5
STEP
With the device unlocked,
insert 4 AA alkaline batteries
into the battery pack.
A B If the reset is successful, the
latch bolt will extend on its own
to learn the handing orientation
of the door.
C
Use the Reset Tool to press and
hold the Reset Button for more
than 5 seconds until you hear a
long "BEEP".
Insert batteries to calibrate the lock handing process.
Reset Button

QUICK START GUIDE
At a Glance
Exterior Assembly Interior Assembly
Outside Indicator
9
Touchscreen Keypad
USB Type-C emergency
power port
Battery Cover
Reset Button
Thumb Turn
Internal Indicator
Z-Wave Module

How to Lock / Unlock
Unlocking the door from outside
Locking the door from outside
Kaadas Home App
/Z-Wave System App
Locking the door from inside
Unlocking the door from inside
Auto Lock Mode
In Auto Lock
mode, the device
will be locked
automatically.
Manually
Rotate the thumb
turn to the lock
position.
Manually
Press any button
on the keypad for
1 second to lock
the door.
Rotate the thumb
turn to the unlock
position.
Auto Lock Mode
In Auto Lock Mode,
the latch bolt is
automatically
extended after
unlocking.
Kaadas Home App
/Z-Wave System App
Kaadas Home App
/Z-Wave System App
10
Master/User PIN Code Kaadas Home App
/Z-Wave System App

Master PIN Code
Required for programming and feature settings, the Master PIN Code
can be used to unlock the door while in away mode. The default
Master PIN Code needs to be changed before programming the lock
for security reasons.
Auto Lock
If the Auto lock feature is enabled, the lock will lock the door 30
seconds after it has been unlocked. This feature is off by default. You
can set the time delay for 30s, 60s, 120s and 180s in both Master
Mode and the Kaadas Home App.
Wrong Entry PIN Code Limit
After 10 attempts of entering an invalid User PIN Code, the unit will
shut down for 3 minutes.
Away Mode
This is a safety feature for you when you leave your house for
vacation or a long trip. When you activate Away Mode, all User PIN
Codes will be locked until the Master PIN Code is entered on the
keypad. When the lock is unlocked by, an alarm will sound for 1
minute. By entering the Master PIN Code on the keypad, you can
disable the alarm and Away Mode.
Silent Mode
The beep sounds when pressing keypad can be muted.But you will
still hear low battery and system alerts.
One Time User Code
This code can only be used once and is automatically deleted after
used.
Low Battery Alarm
If the battery indicator keeps flashing, the batteries are getting low.
For the best performance replace with four new AA alkaline batteries.
Definitions
11

Programming Basics
Code Format
1. Master PIN Code (4 to 10 digits): The default Master PIN Code is
12345678
. Change the default Master PIN Code before programming
other codes.
2. User PIN Code (4 to 10 digits): A total of 250 User PIN Codes (including One-Time PIN Code) can be programmed and
stored in the lock.
3. Both Master and User PIN Codes do not support the following combination of numbers.
Forward number sequence
Backward number sequence
Repeat number sequence
Contain existing code sequence
12

++
+
+
+
13
Z-WaveTM
Module installation and user guide
(Optional network module required)
1. Make sure the network Module is securely plugged in,see page 7, step 4, section E for details.
2. Open the Z-Wave system's smart home or alarm app on your smartphone or tablet and follow the instructions in the app for adding a
new smart lock.
3. Touch the lock keypad with your hand to activate the lock.
4. Enter the Master Mode by Pressing master PIN code (the default master PIN code is 12345678)
5. Press the 0 key key to enter the Network settings.
6. Press the 1 key key to add the module(smart lock) to your Z-Wave system;Press the 2 key key to remove the
module(smart lock) from your Z-Wave system.

Quick Set Up
The default Master Code is 12345678 .
It is required that you change it to a code of
your own before programming.
IMPORTANT:
Delete
User
PIN
Code
Add
User
PIN
Code
Change
Master
PIN
Code
Press
Successful
Green light will flash
Wait for green light to flash Wait for green light to flash Green light will flash
Master
PIN Code
+ +
Master
PIN Code
+ +
Master
PIN Code
+ +
New Master
PIN Code +
Wait for green light to flash
New User
PIN Code +
Unwanted User PIN Code +
Green light will flash
New User
PIN Code +
New Master
PIN Code +
1
Press
Wait for green light to flash
2
Press
Wait for green light to flash
3
Silent
Mode
Silent Mode disabled
when green light flashes
Silent Mode enabled
when green light flashes
Wait for green light to flash
Master
PIN Code
+ +
Press 6+
1
+
2
14

Notes:
1. Beeps only sound when the Silent Mode is disabled.
2. If the indicator light flashes red, your setting failed and you will need to redo the operation.
Auto
Lock
Auto Lock disabled when green light flashes
Auto Lock 30s enabled when green light flashes
Auto Lock 60s enabled when green light flashes
Auto Lock 120s enabled when green light flashes
Auto Lock 180s enabled when green light flashes
Away
Mode Away Mode Enabled
Press
Master
PIN Code
+ +
Wait for green light to flash
Press 7
Master
PIN Code
+ +
Wait for green light to flash
Press 8
+
1
+
2
Join Network when green light flashes
Join Network when green light flashes
+
1
+
2
+
3
+
4
+
5
Wait for green light to flash Green light will flash
New User
PIN Code +New User
PIN Code +
Add one-
time code
Master
PIN Code
+ +
Wait for green light to flash
Press 9
Network
settings
Master
PIN Code
+ +
Wait for green light to flash
Press 0
15

Factory Default Settings
Resetting the device will delete all User PIN Codes and Master PIN Code stored
in the lock.
How to Reset?
Step 1. Keep the door open and the lock unlocked (thumb turn will be vertical).
Step 2. Using the Reset Tool, press and hold the Reset Button for 5 seconds until you hear the
"BEEP" and the latch rotates, turning the thumb turn to the vertical position automatically.
Settings
Master Code
Auto Lock
Silent Mode
Wrong Code Entry Limit
Shutdown Time
Away Mode
Factory Defaut
12345678
Disabled
Disabled
10 times
3 Minutes
Disabled
16
Reset Button

Download Kaadas Home App
Download the Kaadas Home App from the Apple Store or Google
Play Store.
Quick Set Up Tips
Scan the QR Code to download
the Kaadas Home App.
• Create an account in the Kaadas Home App.
• Scan the QR Code found on the inside panel of the Battery Cover to
add your KA210 to the device list.
• The Auto Lock is disabled by default, please complete the
set up process and enable Auto Lock in the Kaadas Home
App.
• The first account to add the lock to their account becomes
the administrator of the lock by default. Only the
administrator account can manage users of the lock.
• To reset the lock, press and hold the Reset Button for 5
seconds until you hear the "BEEP". Log in to the Kaadas
Home App with the administrator account. Go to Settings
and unbind the lock.
IMPORTANT:
17
Table of contents
Other Kaadas Lock manuals
Popular Lock manuals by other brands

Schlage
Schlage LINK FE599 installation instructions

Sargent and Greenleaf
Sargent and Greenleaf V Series Getting started guide

LEHMANN
LEHMANN M410 L033-A01 operating instructions

COMPX
COMPX CB084-184 instruction sheet

DORTRONICS SYSTEMS
DORTRONICS SYSTEMS TJ1107 D Series Mounting instructions

CRP Securities
CRP Securities DB9000 user manual