Trimco UHF211 User manual

INSTALLATION GUIDE# 21825
TRIANGLE BRASS MANUFACTURING
1351 ROCKY POINT DRIVE
OCEANSIDE, CA 92056
WWW.TRIMCOHARDWARE.COM
[e-mail]
323.262.4191
PARTS LIST
STEP 
FOLLOW THE INSTRUCTIONS BELOW FOR STEP BY STEP INSTALLATION.
SCAN QR CODE FOR INSTALLATION VIDEO. FOR INSTALLATION HELP,
PLEASE CONTACT TRIMCO CUSTOMER SERVICE.
*NOT TO SCALE*. IF ANY PARTS ARE MISSING,
PLEASE CONTACT TRIMCO CUSTOMER SERVICE.
PAGE 1 OF 2
DATE: 10/07/2021 REV: 02
INSTALL INTERIOR INDICATOR DECALS:
ADHESIVE IS ON THE GRAPHIC SIDE OF DECAL, AND MUST BE
INSTALLED ON THE BACK OF THE INTERIOR ASSEMBLY TO BE
VISIBLE THROUGH THE INDICATOR WINDOWS.
A. B. D. E.
F. G.
H.
I. J.
K.
C.
M.
L.
BOX 1 ITEMS
(A) 1X INTERIOR ASSEMBLY
(B ) 1X EXTERIOR PLATE
(C) 1X EXTERIOR MACHINE SCREWS, 10-24 X 3/4
(D) 1X CARRIER
(E) 1X LOCKING BOLT
(F) 1 X LATCH FACE AND SCREWS
(G) 1X DOOR STRIKE AND SCREWS
(H) 16X INTERIOR AND EXTERIOR PLATE WOOD/SHEETMETAL SCREWS
(I) 1X INDICATOR WITH OPEN & CLOSE STICKERS
(J) 1X INTERIOR OPEN AND CLOSE STICKERS
(K) 1X EMERGENCY OPEN TOOL
(L) 1X HH SIGN STICKER (FOR HEALTHY HARDWARE ONLY)
(M) 1X HANDS FREE STICKER
REMOVE ALL EXISTING DOOR HARDWARE
INCLUDING THE DEADBOLT IF NEEDED.
INTERIOR SIDE:
INSERT CARRIER AS SHOWN.
INSERT BOLT INTO CARRIER
NOTE: HOLES INDICATE
FOR 2 3/4 OR 2 3/8 DOOR WIDTH
SEE STEP 2
TOOLS
TOOLS BELOW MAY BE REQUIRED. TOOLS NOT INCLUDED.
•CROSSHEAD SCREW DRIVER •PILOT HOLE DRILL (SIZE 3/32)
PARTS
STEP 1
Always refer to WWW.TRIMCOHARDWARE.COM for the latest documentation
-0$, UNLOCK
OVERVIEW UHF211 (INSWING VERSION)
HANDS FREE SLIDE LOCK INSTALLATION GUIDE
PRO TIP:
DEPENDING ON DOOR
HANDING, CHECK TO SEE
THAT THE LOCKED DECAL
IS SHOWN THROUGH THE
CORRECT INDICATOR
WINDOW BY SLIDING THE
BOLT TO THE LOCKED
POSITION. IF INCORRECT,
SWITCH DECALS.
PRO TIP:
NEW INSTALLATIONS FOLLOW ANSI 161 CYLINDRICAL DOOR PREPERATION.
RETROFIT COMPATIBILITY TO ANSI 161 CYLINDRICAL DOOR PREPERATION.
NOTE: ONLY COMPATIBLE WITH 1-3/4" THICK DOORS.

STEP 
STEP 
STEP 
STEP 
INSTALL INTERIOR ASSEMBLY
MOUNTING SCREWS AND
LATCH FACE.
INSTALL EXTERIOR PLATE
DOOR SCREWS.
USE LEVEL OR MEASURE FROM
DOOR EDGE TO ALIGN INTERIOR
ASSEMBLY AND EXTERIOR PLATE.
DOOR
EDGE
INSTALL INDICATOR WITH LEFT OR
RIGHT DECAL, DEPENDING ON
DOOR HANDING.
INSTALL EXTERIOR PLATE
LOOSELY TO INTERIOR
ASSEMBLY STUDS. (DO NOT
TIGHTEN UNTIL PLATES ARE
ALIGNED TO DOOR).
INSTALL INTERIOR ASSEMBLY
(STUDS THROUGH CARRIER).
CHOOSE THE CORRECT DECAL
LEFT AND RIGHT HANDED
DECALS ARE PROVIDED.
PRO TIP: USE TAPE
TO HOLD ASSEMBLY IN PLACE WHILE THE
EXTERIOR PLATE IS BEING INSTALLED.
PRO TIP:
TO INSURE PROPER FUNTION LATCH PLATE
AND STRIKE MUST BE PROPERLY ALIGNED.
PRO TIP:
EXTEND LATCH BOLT WHEN TIGHENING
OUTER PLATES TO DOOR SURFACE. THIS
HELPS INSURE ALIGNMENT.
INSTALLATION GUIDE# 21825
PAGE 2 OF 2
DATE: 10/07/2021 REV: 02
Always refer to WWW.TRIMCOHARDWARE.COM for the latest documentation