Trinamic PD-1141 User manual

Getting started PD-1141
TRINAMIC Motion Control GmbH & Co. KG
Hamburg, Germany
www.trinamic.com
YOU NEED
-PD-1141
-Serial interface: RS485 or USB
-If you choose RS485: interface converter
suitable to your module
-Supply voltage +24V DC (9… 28V DC)
-TMCL-IDE program and PC
-Cables for interface, motor, and power
PRECAUTIONS
-Do not mix up connections or short-circuit pins.
-Avoid bounding I/O wires with motor power
wires.
-Do not exceed the maximum power supply of
+28V DC!
-Do not connect or disconnect the motor while
powered!
-START WITH POWER SUPPLY OFF!
STARTING UP
1. Choose your interface.
USB: connect USB interface to PC.
Download and install the file TMCM-
1141.inf (www.trinamic.com) after
connecting the power supply.
RS485: use the interface connector and
connect an interface converter.
Connect the chosen interface to PC.
2. Connect the 24V DC power supply.
3. Turn power ON. The green LED starts
flashing slowly and the motor is
powered but in standstill now. If this
does not occur, turn power OFF and
check your connections and power
supply!
4. Start the TMCM-IDE program.
See next page how to configure the
connection and to use the IDE.
5. Type in the open window:
ROL 0, 500 //Rotate motor 0 with speed 500
WAIT TICKS, 0, 500
MST 0
ROR 0, 250 //Rotate motor 0 with speed 250
WAIT TICKS, 0, 500
MST 0
6. Click the Assemble icon. Thereafter click the Download icon to download the code to the module.
Click the Run icon. The program will now be executed.
7. Click the Stop icon and start TMCL™Direct Mode to issue the following commands:
ROR rotate right, motor 0, value 500 -> click Execute / The motor is rotating now.
MST motor stop, motor 0-> click Execute / The motor stops now.
FIRST STEPS ARE MADE.
Please refer to the PD-1141 Hardware and Firmware Manuals, too.
Motor
1
1
1
Power & RS485
In/Out
S/D
USB
QSH4218
1
Serial USB
interface
Converter
e.g. USB-2-485
Power supply
Pin 1 GND
Pin 2 9… 28V DC
RS485
Pin 3 GND
Pin 4 RS485+
Pin 5 RS485-
USB
RS485

Getting started PD-1141
TRINAMIC Motion Control GmbH & Co. KG
Hamburg, Germany
www.trinamic.com
TMCL-IDE
The TMCL-IDE is available on www.trinamic.com.
6. Click Assemble first, then Download and
Run to start the program.
Assemble
Download Run StopDissemble Continue
7. Stop all running programs by clicking
Stop and start Direct Mode by clicking the
appropriate icon.
8. The PD-1141 is automatically detected, if
the communication is established.
9. Issue a command by choosing Instruction,
Type, Motor, and Value and click Execute
to send it to the module.
1. Make sure the COM port you intend to
use is not blocked by another program.
2. Open TMCL-IDE by clicking TMCL.exe.
3. Choose Setup and Options and
thereafter the Connection tab.
4. Choose COM port and Type. Click OK.
5. Write a program code into the white
field and save it with File/Save.
Note, that TMCL programs run
standalone on the module, too.
TROUBLESHOOTING
IF COMMUNICATION IS NOT ESTABLISHED
-Check if the green LED lights up. If not, check
your power supply.
-Try to start Direct Mode and check, if the
module is detected automatically.
-Check, if you are using the right COM port and
it is not blocked by another program.
-Check, if the file TMCM-1141.inf is installed
correctly.
-Check your connection settings. Default: 9600
baud, address 1.
-Check if the RS485 converter functions.
IF MOTOR DOES NOT RESPOND
-Usually the communication is not established
(see above).
-Check the motor connection.
-If you are using a TMCL program try a
movement command in Direct Mode to check
if there is a problem with it.
-Restore factory settings by using instruction
137 for cancelling all settings modified by the
user.