Tripp Lite SmartOnline S3MX User manual

1
Owner’s Manual
SmartOnline®S3MX
3-Phase UPS Systems
Models: S3M30KX, S3M30KXD, S3M30KX-NIB, S3M30KXD-NIB,
S3M40KX, S3M40KXD, S3M40KX-NIB, S3M40KXD-NIB, S3M60KX,
S3M60KXD, S3M80KX, S3M80KXD
Input: 220/230/240V (Ph-N), 380/400/415V (Ph-Ph), 3Ø 4-Wire + PE
1111 W. 35th Street, Chicago, IL 60609 USA • tripplite.com/support
Copyright © 2019 Tripp Lite. All rights reserved.

2
Table of Contents
1. Introduction 3
2. Important Safety Warnings 4
2.1 UPS Location Warnings 4
2.2 Equipment Connection Warnings 4
2.3 Battery Warnings 4
2.4 Transportation and Storage 5
2.5 Preparation 5
2.6 Installation 5
2.7 Connection Warnings 5
2.8 Operation 6
2.9 Standards 6
3. Installation and Setup 7
3.1 Unpacking and Inspection 7
3.2 Internal Battery Connection Procedure for 9
S3M30KX/KXD and S3M40KX/KXD Models
3.3 Installation of Internal Batteries in 10
S3M30KX-NIB/KXD-NIB and
S3M40KX-NIB/KXD-NIB Models
3.4 Single UPS Installation 22
3.5 UPS Installation for Parallel Systems 24
3.6 External Battery Connection 25
3.7 Dual AC Input Installation 26
4. Operation 27
4.1 Display Button Operation 27
4.2 LED Indicators and LCD Panel 27
4.3 Audible Alarm 29
4.4 Single UPS Operation 29
4.5 Parallel UPS Operation 32
4.6 LCD Panel Abbreviations 34
4.7 Setup Menu 34
4.8 Operating Mode/Status Description 41
4.9 Fault Codes 46
4.10 Warning Indicator 47
4.11 Warning Code 47
5. Communication 48
5.1 SNMP Monitoring Slot 48
5.2 EPO Connector 48
5.3 RS-232 Port 48
5.4 USB Port 48
6. Troubleshooting 49
7. Storage and Maintenance 50
7.1 Storage 50
7.2 Maintenance 50
7.3 Battery 50
7.4 Fan 50
8. Specifications 51
9. Warranty 54
Español 55
Français 109
Русский 163
Deutsch 217

3
1. Introduction
Tripp Lite’s SmartOnline S3MKX-Series Uninterruptible Power Supply (UPS) is a Voltage and Frequency Independent (VFI) true on-line,
double-conversion 3-phase UPS system. This UPS continuously conditions the incoming electrical power supply, eliminating power
disturbances that will otherwise damage sensitive electronic devices and minimising system downtime from power fluctuations and
interruptions.
S3MKX-Series UPS systems are designed to the highest quality and performance standards and offer the following features:
Model Agency Number Internal Batteries AC Inputs Capacity
S3M30KX AG-6030 Yes Single 30kVA
S3M30KXD AG-6030 Yes Dual 30kVA
S3M30KX -NIB AG-6031 No Single 30kVA
S3M30KXD-NIB AG-6031 No Dual 30kVA
S3M40KX AG-6040 Yes Single 40kVA
S3M40KXD AG-6040 Yes Dual 40kVA
S3M40KX -NIB AG-6041 No Single 40kVA
S3M40KXD-NIB AG-6041 No Dual 40kVA
S3M60KX AG-6060 No Single 60kVA
S3M60KXD AG-6060 No Dual 60kVA
S3M80KX AG-6080 No Single 80kVA
S3M80KXD AG-6080 No Dual 80kVA
• True on-line UPS – the highest level of UPS protection, fully regulates the incoming power with zero transfer time to battery in the event
of an extended mains failure, so critical loads remain continuously supported
• Paralleling for capacity and redundancy of up to three UPS systems
• High-efficiency performance in AC On-line and Battery Standby Modes minimise energy consumption
• Market-leading compact footprint, so more power can be provided from smaller spaces
• ECO Mode allows the UPS to operate on bypass in stable utility conditions, and immediately transfers to inverter to support the load
when the utility input drops below tolerance
• High output power factor – more actual power allows more equipment to be supported
• Automatic and manual bypass increase system reliability and allow for maintenance without removing power from the attached load
• Wide input voltage window – the UPS system regulates even poor-quality incoming power without reverting to battery, maximising system
uptime and protecting battery life
• Matching external battery cabinets allow for increased battery autonomy
• Emergency shutdown via REPO
• SNMP Network Monitoring and Control and Contact-Closure Management cards available
• Optional dual-AC input “KXD” models available
SmartOnline S3MKX-Series UPS systems are ideally suited for protecting 4-wire loads in the following mission-critical electrical applications:
• IT infrastructure and data centres
• Edge IT installations
• Telecommunications
• Networks (LAN/WAN)
• Corporate infrastructure
• Security and emergency systems
• Financial institutions
• Healthcare and hospitals

4
2. Important Safety Warnings
SAVE THESE INSTRUCTIONS
This manual contains important instructions and warnings that should be followed during the installation and maintenance
of all Tripp Lite SmartOnline S3MX 3-Phase 30kVA, 40kVA, 60kVA and 80kVA UPS Systems and their batteries. Failure to
heed these warnings may affect your warranty.
2.1 UPS Location Warnings
• Install the UPS indoors, away from heat, direct sunlight, dust and excess moisture or other conductive contaminants.
• Install the UPS in a structurally sound area. The UPS is extremely heavy; take care when moving and lifting the unit.
• Only operate the UPS at indoor temperatures between 0° C and 40° C.
• Optimum UPS performance and maximum battery life is obtained when the operating temperature is maintained between
17° C and 25° C.
• Ensure the installation area has sufficient space for maintenance and ventilation of the UPS system. Maintain a minimum clearance of
50 cm from the rear, front and both sides of the UPS for maintenance and ventilation.
• Do not install the UPS near magnetic storage media, as this may result in data corruption.
2.2 Equipment Connection Warnings
• Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the
life support equipment or to significantly affect its safety or effectiveness is not recommended.
• The UPS system contains its own energy source (battery). The output terminals may be live, even when the UPS is not connected to an
AC supply.
• The UPS models covered in this manual are not compatible with loads that do not have a Neutral Reference or Delta load.
2.3 Battery Warnings
This UPS contains LETHAL VOLTAGES. The UPS is designed to supply power, even when disconnected from utility power. Only
AUTHORISED SERVICE PERSONNEL should access the interior of the UPS after disconnecting utility and DC power.
Batteries present a risk of electrical shock and burns from high short-circuit current. Battery connection or replacement should be
performed only by qualified service personnel, observing proper precautions. Turn off the UPS before connecting or disconnecting
internal batteries. Use tools with insulated handles. Do not open the batteries. Do not short or bridge the battery terminals with any
object.
• The batteries are recyclable. Refer to local codes for disposal requirements or visit tripplite.com/support/recycling-program for recycling
information.
• Do not dispose of the batteries in a fire, mutilate the batteries or open the battery coverings. Escaping electrolytes may be toxic and
cause injury to skin and eyes.
• Do not disconnect the batteries while the UPS is in Battery Mode.
• Disconnect the charging source prior to connecting or disconnecting terminals.
• The following precautions should be observed:
1) Remove watches, rings and other metal objects.
2) Use tools with insulated handles.
3) Wear rubber gloves and electrical-grade boots.
4) Use an electrical-grade rubber mat while servicing batteries.
5) Do not lay tools or metal parts on top of batteries or battery cabinets.
6) Determine whether the battery supply (+, -, N) is inadvertently grounded. If it is, remove the source of the ground. Contact with any
part of a grounded battery can result in electric shock. The likelihood of an electric shock is reduced if such grounds are removed
during installation and maintenance.
• Battery replacement should be performed only by authorised service personnel, using the same number and type of batteries (sealed
lead acid).
WARNING: In order to avoid any hazardous conditions during UPS installation and maintenance, these tasks may be
performed only by qualified and experienced electricians.
Please read this Owner’s Manual and the safety instructions carefully before installing or using the unit.

5
2.4 Transportation and Storage
To protect against shock and impact, transport the UPS system only in the original packaging.
The UPS must be stored in a room that is dry and ventilated.
2.5 Preparation
Condensation may occur if the UPS system is moved directly from a cold to a warm environment. The UPS system must be completely
dry before being installed. Please allow at least two hours for the UPS system to adjust to the environment.
Do not install the UPS system near water or in moist environments.
Do not install the UPS system in direct sunlight or near heat sources.
Do not block the ventilation holes on the UPS system’s housing.
2.6 Installation
Do not connect appliances or devices that could overload the UPS (i.e., equipment with large electrical motors) to the UPS output
sockets or terminal.
Carefully arrange cables so no one can step on or trip over them.
Do not block the UPS system’s air vents. The UPS must be installed in a location with good ventilation. Ensure adequate ventilation
space on each side of the unit.
The UPS contains an earthed terminal. In the final installed system configuration, ensure equipotential earth grounding to the external
UPS battery cabinet by connecting the earth terminals of both cabinets together.
The UPS should only be installed by qualified maintenance electrical service personnel.
An appropriate disconnect device such as short-circuit backup protection must be provided in the building wiring installation.
An integral single-emergency switching device should be included in the building wiring installation.
Connect the earth ground before connecting to the building wiring terminal.
Installation and wiring must be performed in accordance with local electrical codes and regulations.
2.7 Connection Warnings
The UPS system does not contain standard backfeed protection inside. Isolate the UPS before working on this circuit. The isolation
device must be able to carry the UPS input current.
• This UPS should be connected with TN earthing system.
• The power supply for this unit must be 3-phase rated in accordance with the equipment nameplate. It also must be suitably grounded.
• The input power to 3-phase UPS models requires a 4-pole breaker.
• Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the
life support equipment or to significantly affect its safety or effectiveness is not recommended.
• Connect the UPS power module’s grounding terminal to a grounding electrode conductor.
• The UPS is connected to a DC energy source (battery). The output terminals may still be live even when the UPS is not connected to an
AC supply.
2. Important Safety Warnings
Input
UPS
«Automatic backfeed protection
system» input, external to the UPS
(EN-IEC 62040-1)

6
2. Important Safety Warnings
When installing the unit, verify that any maintenance bypass panel used is configured correctly before applying power to the unit.
• Be sure to place a warning label on all primary power isolators installed remotely from the UPS area and on any external access points
between such isolators and the UPS. The warning label shall carry the following wording or equivalent.
Before working on this circuit
- Isolate Uninterruptible Power System (UPS)
- Then check for Hazardous Voltage between all terminals
including the protective earth.
Risk of Voltage Backfeed
2.8 Operation
Do not disconnect the earth conductor cable on the UPS or the building wiring terminals at any time, as this will cancel the protective
earth of the UPS system.
In order to fully disconnect the UPS system, first press the “OFF” button, then disconnect the mains.
Ensure no liquid or other foreign objects can enter into the UPS system.
2.9 Standards
*Safety
IEC 62040-1: 2008+A1:2013
*EMI
Conducted Emission.....................................EN 62040-2: 2006 Category C3
Radiated Emission .......................................EN 62040-2: 2006 Category C3
*EMS
ESD............................................................EN 61000-4-2 Level 4
RS .............................................................EN 61000-4-3 Level 3
EFT. ............................................................EN 61000-4-4 Level 4
SURGE .......................................................EN 61000-4-5 Level 4
CS .............................................................EN 61000-4-6 Level 3
Power-Frequency Magnetic Field....................EN 61000-4-8 Level 4
Low-Frequency Signals .................................EN 61000-2-2
Warning: This is a product for commercial applications. Installation restrictions or additional precautions may be needed to
prevent disturbances.

7
3. Installation and Setup
3.1 Unpacking and Inspection
Unpack the unit and inspect the contents. Packaging may include additional accessories and components, depending on specific
customer orders.
• One (1) UPS
• One (1) Owner’s Manual
• One (1) RS-232 Cable
• One (1) 1.5 m battery cable kit extension (included with 30K and 40K models only)
Cabling for UPS Paralleling:
• One (1) parallel cable (only available for parallel model) for every set of UPS units being paralleled
• One (1) shared current cable (only available for parallel model) for every set of UPS units being paralleled
Other Accesory and Component Options Available
Additional Charging Board to increase the battery charger capacity:
• 4A charger boards may be paralleled to increase the charger’s current capacity. For more information, refer to ACCESSORIES in section
8. Specifications.
Note: Do not turn on the unit. Make sure to inspect the unit prior to installation. Ensure nothing inside the package was damaged during transportation.
Notify the carrier and dealer immediately if there is any damage or missing parts. Please keep the original packaging in a safe place for future use.
Rear Panel View - 30K and 40K Models
30K Rear Panel 40K Rear Panel 30K and 40K Input/Output Terminals
1RS-232 Communications Port
2USB Communications Port
3Emergency Power Off (EPO) Connector
4Share Current Port for Paralleling Units
5Parallel Ports for Paralleling Units
6SNMP Slot for Network Monitoring using
(Optional WEBCARDLX)
7External Battery Cabinet Connector
8Input Circuit Breaker
9Maintanance Bypass Switch
(for Service Personnel Use Only)
10 Input/Output Terminal
(Refer to 11 and 12 for Details)
11 Input Terminal
12 Output Terminal
(Connects to Mission-critical Loads)
13 Input Grounding Terminal
14 Output Grounding Terminal
15 * Input 2 Circuit Breaker
16 * Input 2 Terminal (Bypass Input)
*Input 2 (Bypass Input) and Input 2 Circuit Breaker
for “KXD” dual input models only.

8
3. Installation and Setup
Front Panel View - 60K Model
1
16
124 1
16
35
124 135
19
19
112
115
1
8
1
16
17
1
11
16
3
14
112
111
112
111
UPS INPUT~ ~BYPASS INPUT
~OUTPUT
~BYPASS INPUT
~OUTPUT
R S T N
UPS INPUT~
R S T N
BYPASS INPUT~
OUTPUT~
R S T N
113
14
1
13
1
8
1
16 *
*
*
Input Output
Input Output
1
10
112
115
17
1
11 *
1
10
60KXD Front View with Door Open
Front Panel View - 80K Model
1
16
124 1
16
35
124 135
19
19
112
115
1
8
1
16
17
1
11
16
3
14
1
12
111
112
111
UPS INPUT~ ~BYPASS INPUT
~OUTPUT
~BYPASS INPUT
~OUTPUT
R S T N
UPS INPUT~
R S T N
BYPASS INPUT~
OUTPUT~
R S T N
113
14
113
1
8
1
16 *
*
*
Input Output
Input Output
1
10
112
115
17
1
11 *
1
10
80KXD Front View with Door Open
1RS-232 Communications Port
2USB Communications Port
3Emergency Power Off (EPO) Connector
4Share Current Port for Paralleling Units
5Parallel Ports for Paralleling Units
6SNMP Slot for Network Monitoring using
(Optional WEBCARDLX)
7External Battery Cabinet Connector
8UPS Input Switch
9Maintanance Bypass Switch
(for Service Personnel Use Only)
10 Input/Output Terminal
(Refer to 11 and 12 for Details)
11 Line Input Terminal
12 Output Terminal
(Connects to Mission-critical Loads)
13 Input Grounding Terminal
14 Output Grounding Terminal
15 * Input 2 Terminal (Bypass Input)
16 * Input 2 Switch
* Input 2 (Bypass Input) and Input 2 Switch for
“KXD” dual input models only.
60K Terminals
80K Terminals
60K Terminals
80K Terminals
1RS-232 Communications Port
2USB Communications Port
3Emergency Power Off (EPO) Connector
4Share Current Port for Paralleling Units
5Parallel Ports for Paralleling Units
6SNMP Slot for Network Monitoring using
(Optional WEBCARDLX)
7External Battery Cabinet Connector
8UPS Input Circuit Breaker
9Maintanance Bypass Switch
(for service personnel use only)
10 Input/Output Terminal
(Refer to 11 and 12 for details)
11 UPS Input Terminal
12 Output Terminal
(Connects to Mission-critical Loads)
13 Input Grounding Terminal
14 Output Grounding Terminal
15 * Input 2 Terminal (Bypass Input)
16 * Input 2 Circuit Breaker
Input 2 (Bypass Input) and Input 2 Circuit Breaker for
“KXD” dual input models only.

9
3. Installation and Setup
3.2 Internal Battery Connection Procedure for S3M30KX, S3M30KXD, S3M40KX,
S3M40KXD Models
DANGER! LETHAL HIGH VOLTAGE HAZARD!
Potentially lethal high voltage exists within the batteries, even when not connected to a UPS system. Battery
connection should be performed by qualified service personnel only, following all the precautions listed in this manual
and adhering to local electrical codes. Refer to section 2.3 Battery Warnings.
Internal Battery Connection Procedure
1) Remove all screws labeled 1 (Figure 3.1).
2) Remove top plate, right side and left side plates (Figure 3.2).
See next page for steps 3-5.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Figure 3.1 Figure 3.2

10
3. Installation and Setup
3) For 30kVA and 40kVA units with internal batteries, there are four battery cable points that are disconnected for shipping purposes
(refer to Figures 3.3 and 3.4). These four cables (two on the right side and two on the left side) will need to be reconnected for proper
battery cabinet operation.
Figure 3.3 Figure 3.4
4) Re-Install the top and side panels from Step 2.
5) Re-Install and tighten all screws from Step 1 with a torque of 1 N•m.
3.3 Installation of Internal Batteries in S3M30KX-NIB, S3M30KXD-NIB, S3M40KX-NIB, and
S3M40KXD-NIB Models
DANGER! LETHAL HIGH VOLTAGE HAZARD!
Be careful to observe all safety warnings in the manual, especially those in section 2.3 Battery Warnings.
Battery installation should be performed by qualified electrical service personnel only.
Items needed:
1) Protective equipment (rubber gloves, electrical rated boots, electrical rated rubber floor mat, etc. as outlined in section 2.3 Battery
Warnings).
2) 80x Sealed Lead Acid Batteries: 12V 9Ah (Non-Spillable VRLA AGM/GEL). Batteries must be UL-recognised to UL 1989, UL CCN:
BARZ2.
3) Tripp Lite Wiring Kit PN: ACC-0442. Check the wiring kit to make sure all necessary items are there. This kit includes:
CABLE CABLE LENGTH QUANTITY
175 mm 56
2160 mm 4
3250 mm 9
4350 mm 3
5700 mm 2
6800 mm 1
7930 mm 1
Battery cables that need to be reconnected
before proper operation of battery cabinet
Left Side
S3M30KX/S3M30KXD
S3M40KX/S3M40KXD
Right Side
S3M30KX/S3M30KXD
S3M40KX/S3M40KXD

11
3. Installation and Setup
1) Take off top and side panels by removing all screws. 2) Remove the battery bracket bars on the right and left sides of
the UPS.
3) Install 11 battery packs to the layer (L1-a). Be sure to keep
terminal sides of all batteries up.
5
6
7
8
9
10
11
12
13
14
15
5
6
7
8
9
10
11
12
13
14
15
Battery_Front view
4) Install another 11 battery packs to the layer (L2-a). Be sure to
keep terminal sides of all batteries up.
5
6
7
8
9
10
11
12
13
14
20
21
22
23
24
25
26
27
28
29
30
5) Install another 9 battery packs to the layer (L3-a). Be sure to
keep terminal sides of all batteries up.
20
21
22
23
24
25
26
27
28
5
6
7
8
9
10
11
12
13
14
35
36
37
38
39
40
78
79
80

12
3. Installation and Setup
6) Install another 11 battery packs to the layer (L1-b). Be sure to
keep terminal sides of all batteries up.
20
21
22
23
24
25
26
27
28
35
36
37
38
39
40
78
5
6
7
8
9
10
11
12
13
14
51
50
49
48
47
46
45
44
43
42
41
7) Install another 11 battery packs to the layer (L2-b). Be sure to
keep terminal sides of all batteries up.
51
50
49
48
47
46
45
44
43
42
41
20
21
22
23
24
25
26
27
28
35
36
37
38
39
40
78
60
59
58
57
56
55
54
53
52
77
76
10) Install another 2 battery packs to the layer (L6). Be sure to
keep terminal sides of all batteries down.
8) Install another 8 battery packs to the layer (L3-b). Be sure to
keep terminal sides of all batteries up.
60
59
58
57
56
55
54
53
52
77
76
51
50
49
48
47
46
45
44
43
42
41
74
73
72
71
70
69
68
75
9) Install another 5 battery packs to the layer (L4 and L5). Be sure
to keep terminal sides of all batteries up.
60
59
58
57
56
55
54
53
52
77
76
51
50
49
48
47
46
45
44
43
42
41
74
73
72
71
70
69
68
75
63 64
65 66
67
60
59
58
57
56
55
54
53
52
77
76
51
50
49
48
47
46
45
44
43
42
41
74
73
72
71
70
69
68
75
62 61
65 66
63
67
64

13
3. Installation and Setup
11) Reattach the six battery bracket bars removed in step 2.
12) On the right side of the UPS, use 30 pieces of cable 1to connect two terminals on all batteries shown below.
1
1

14
3. Installation and Setup
13) • Use one cable 7to connect #51 and #52 batteries.
• Use one cable 6to connect #75 and #76 batteries.
• Use one cable 5to connect #67 and #68 batteries.
• Use one cable 4to connect #64 and #65 batteries.
• Use one cable 2to connect #62 and #63 batteries.
62
63 64
65
67
68
75
76 52
51
14) On the left side of the UPS, use 26 pieces of cable 1to connect two terminals on all batteries.
2
4
5
6
7
1

15
3. Installation and Setup
15) Use one cable 5to connect #77 and #78 batteries.
5
7878
77
16) Install another 4 battery packs to the layer (L1). Be sure to keep terminal sides of all batteries up.
1
2
3
4
5
Left Side
Right Side

16
3. Installation and Setup
17) • Use one cable 2to connect #4 and #5 batteries.
• Use one cable 3to connect #3 and #4 batteries.
• Use one cable 3to connect #2 and #3 batteries.
• Use one cable 3to connect #1 and #2.
333
2
1
23
4
18) Install another 4 battery packs to the layer (L2). Be sure to keep terminal sides of all batteries up.
16
17
18
19
1
2
3
4
23 3 3

17
3. Installation and Setup
19) • Use one cable 2to connect #19 and #20 batteries.
• Use one cable 3to connect #18 and #19 batteries.
• Use one cable 3to connect #17 and #18 batteries.
• Use one cable 3to connect #16 and #17 batteries.
• Use one cable 4to connect #15 and #16 batteries.
2
4
333
15
1
2
3
4
19 18 17 16
20) Install another 4 battery packs to the layer (L3). Be sure to keep terminal sides of all batteries up.
31
32
33
34
1
2
316
17
18
19
2 3 33
4

18
3. Installation and Setup
21) • Use one cable 2to connect #34 and #35 batteries.
• Use one cable 3to connect #33 and #34 batteries.
• Use one cable 3to connect #32 and #33 batteries.
• Use one cable 3to connect #31 and #32 batteries.
• Use one cable 4to connect #30 and #31 batteries.
4
3
3
2
3
1
2
3
4
19 18 17 16
33 32 31
34
30
22) Reattach the battery brackets.
2
3 3 3
4

19
3. Installation and Setup
23) Use a meter to measure the positive pole of #20 battery and
the negative pole of #1 battery. (DC voltage should be within
240V~270V)
24) Use a meter to measure the positive pole of #40 battery and
the negative pole of #21 battery. (DC voltage should be within
240V~270V)
25) Use a meter to measure the positive pole of #80 battery and the negative pole of #61 battery. (DC voltage should be within
240V~270V)
26) Use one meter to measure the positive pole of #60 battery and the negative pole of#41 battery. (DC voltage should be within
240V~270V)

20
3. Installation and Setup
27) Use the Battery Fuse PCB to connect batteries and refer to the Figures 3.5, 3.6 and 3.7. Refer to Table 3.1 for a complete battery
wiring listing.
BAT +1 cable to positive pole of #40 battery. BAT -1 cable to negative pole of #1 battery.
BAT +2 cable to positive pole of #80 battery. BAT -2 cable to negative pole of #41 battery.*
BAT N1 cable to positive pole of #20 battery. BAT N2 cable to negative pole of #21 battery.
BAT N3 cable to positive pole of #60 battery. BAT N4 cable to negative pole of #61 battery.
Figure 3.5 Figure 3.6
Figure 3.7
Notes:
• The blue numbers in above figures are “Battery Numbers” from 1 to 80, which are used for battery position identification.
• There are 2 red wires, 2 black wires and 4 blue wires, which connect the battery fuse board and batteries.
• S3M30KX/KXD/NIB battery fuse board part number: 71-303365-XXG.
• S3M40KX/KXD/NIB battery fuse board part number: 71-303366-XXG.
Left Side
S3M30KX/S3M30KXD
S3M40KX/S3M40KXD
Right Side
S3M30KX/S3M30KXD
S3M40KX/S3M40KXD
Battery Fuse PCB
Input BAT-1 Input BAT +1
BAT +1 BAT +2
BAT N4
BAT N3
BAT -2*
BAT -1
BAT -2 BAT +2
BAT N1
BAT N3 BAT N4
BAT N2
* Only the BAT -2 cable and connector is routed through the cable grommet.