Tristar Products Trix Trux Hot Rod User manual

2
IMPORTANT SAFEGUARDS
WARNING
Prevent injuries! Carefully read
all instructions before use!
• Choking Hazard - Small Parts. Not for children
under 3years.
• Please use as directed.
• Adult assembly may be required.
• Please keep these instructions for future reference
as they contain important information.
• The cords on this product present a potential
strangulation hazard. To avoid strangulation
and entanglement, keep cords out of reach
of young children. Cords may become wrapped
around a child’s neck.

3
IMPORTANT SAFEGUARDS 2
Components 4
Battery Installation and Vehicle Operation 6
Stunt Ramp Assembly 8
Connecting Track 9
Monster Ramp Stunt 10
Tidal Wave Stunt 12
Rumble Road/Cliffhanger Stunt 14
Double Stunt Super Challenge 16
Aerial Stunt 18
Labeling 22

4
Components
MOTORIZED
VEHICLE (x1)
AERIAL
CLAMP (x1)
AERIAL LINE
HOLDER (x1)
RUMBLE ROAD/
CLIFFHANGER STUNT (x1)
TIDAL WAVE
STUNT (x1)
MONSTER RAMP
STUNT (x1)
ASSEMBLY REQUIRED
Side Rails (x2),
Rail Connectors (x3)
Side Rails (x2),
Rail Connectors (x3)
Side Rails (x2),
Rail Connectors (x3)
STUNT-TO-STUNT
CONECTOR (x2)
FLIP
TAB (x1)
AERIAL-TO-TRACK
CONNECTOR (x1)
DECAL
SHEET (x1)

5
NOTE: Not to scale.
STRAIGHT
TRACK (x3)
CURVED
TRACK (x3)
RAIL CONNECTOR
(x6)
C-CURVE
TRACK (x2)
TRACK-TO-TRACK
CONNECTOR (x6)
AERIAL
LINE (x2)

6
•Loosen screw on
the back of the vehicle
with a Phillips-head screw
driver by turning counter
clockwise.
•Lift vehicle body
from chassis as shown
and unhook from
the latch on the front
of the vehicle.
•Note the markings
that show the battery
orientation.
Battery Installation and Vehicle Operation
BACK
FRONT

7
•Insert 3 AAA batteries
as shown.
•Replace vehicle body
and tighten the screw
by turning screwdriver
clockwise.
•Slide button on
the back of the vehicle
right to turn the vehicle
on, and slide it left
to turn the vehicle o.

8
•For each of the three
stunt ramps, snap
in three rail connectors
of matching color.
•Correctly assembled stunt
ramps should look as
shown.
Stunt Ramp Assembly
For the Monster Ramp stunt,
levers should be
to the outside of rails.
MONSTER RAMP TIDAL WAVERUMBLE ROAD/
CLIFFHANGER

9
•Connect track to stunts
by plugging the track
onto the pegs on the rail
connectors.
•Connect two pieces
of track together
by plugging the track
onto both ends of a rail
connector.
•Connect two pieces
of track together
by plugging the track
onto both ends of a track-
to-track connector.
Connecting Track
OR

10
•Aim V grooves of res
at the side rails
on the stunt.
•Aach track to stunt
and place vehicle on track
to guide vehicle
to the stunt.
Monster Ramp Stunt
OR
UNDERSIDE VIEW
Place vehicle on track
with the track between
the front and rear guides
on the bottom
of the vehicle.

11
•Flip levers down
as shown for easy
noseplant stunt.
•Challenge mode: ip levers
up as shown for dicult
noseplant stunt.
OR

12
•Aim V grooves of res
at the side rails
on the stunt.
•Aach track to stunt
and place vehicle on track
to guide vehicle
to the stunt.
OR
Tidal Wave Stunt

13
•Watch it surf the wave.

14
•Aim V grooves of res
at the side rails
on the stunt.
•Aach track to stunt
and place vehicle on track
to guide vehicle
to the stunt.
Rumble Road/Cliffhanger Stunt
OR

15
•Run vehicle through lower
level for rumble road
challenge.
•Place vehicle on top level
for cli hanger challenge.
Can you get it
to noseplant?

16
•Use special stunt-to-
stunt connector to aach
monster ramp stunt
to Rumble Road/
Clianger stunt.
•Correctly connected stunts
should look
as shown.
Double Stunt Super Challenge
OR

17
•Flip levers on Monster
Ramp up as shown
to acvate hanging
Clianger challenge.

18
Aerial Stunt
•Snap the connector on the two lines into
the aerial clamp as shown.
•Snap the other ends of the two lines into
the line holder as shown.

19
•Place aerial clamp on the edge of a table
or shelf and turn the screw clockwise
to secure it ght. Turn screw counterclockwise
to loosen it.
•Place the V grooves of the res on top
of the lines as shown for high-wire acon.

20
Aerial Stunt
•Hang the vehicle upside down with
the V grooves of the tires on top of the lines
as shown for inverted ipped-out action.
•Place the V grooves of the front two tires
on top of the lines as shown for hanging
high-wire action.