TroposAir Estero 52DFN-L User manual

Owner’s ManualOwner’s Manual
Estero
Toll Free 1-855-676-7247
WARNING: Read and follow these instructions carefully and be mindful of all warnings shown throughout.
Net Weight
5.7 KGS
12.6 LBS
These instructions contain 5 pages:
Page 1: Foreword
Page 2: Unpack and inspect parts contained, and pre-installation notes
Page 3: Hanging system installation
Page 4: Wiring connections and Canopy and Blade installation
Page 5: Light/Cover installation and Remote Setting
Model No:
52DFN-L

To ensure success of installation, be sure read these instructions and review the
diagrams thoroughly before beginning.
To avoid possible electric shock, be sure electricity is turned off at the main
power box before wiring.
All electrical connections must be made in accordance with local codes, ordinances
and/or the National Electrical Code. If you are unfamiliar with the methods of installing
electrical wiring and products, secure the services of a qualified and licensed
electrician as well as someone who can check the strength of the supportive ceiling
members and make the proper installations and connections.
Make sure that your installation site will not allow rotating fan blades to come into
contact with any object. Blades should be at least 7 feet from the floor when fan is in
operation.
If possible, mount ceiling fan on a ceiling joist - the joist must be able to support the
motion and weight of the moving fan. If the fan will be mounted on a ceiling outlet box,
a 4” x 2 1/8” deep METAL octagon box is required; one UL listed as “suitable for fan
support”. The box and its supporting members must not be able to twist or work loose.
DO NOT USE PLASTIC BOXES. Installation on a concrete ceiling should be
performed by qualified personnel.
Blades should be attached after motor housing is hung and in place. Fan motor
housing should be kept in carton until ready to be installed to protect its finish. If you
are installing more than one ceiling fan, make sure that you do not mix fan blade sets.
After making electrical connections, spliced conductors should be turned upward and
pushed carefully up into the outlet box. The wires should be spread apart with the
grounded conductor and the equipment-grounding conductor on one side of the outlet
box and the “HOT” wires on the other side.
Electrical diagrams are for reference only. Light kits that are not packed with the fan
must be UL/ETL listed and should be installed per the light kit’s installation instructions.
After fan is completely installed, check to make sure that all connections are secure to
prevent fan from falling and/or causing damage or injury.
The fan can be made to work immediately after installation. The bearings are
adequately charged with grease, so that, under normal conditions, further lubrication
should not be necessary.
The fan turns off and stops before reversing fan direction.
This fan is suitable for sloped ceiling.
This fan is electrically reversible.
This fan includes a light.
This fan is controlled by remote control.
This fan is suitable for indoor use or damp location use.
READ AND SAVE THESE INSTRUCTIONS
WARNING : TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY
TO PERSONS, PLEASE OBSERVE THE FOLLOWING:
1.]
2.]
3.]
4.]
5.]
6.]
7.]
8.]
9.]
10.]
11.]
12.]
13.]
14.]
15.]

Unpack and inspect fan carefully to be certain
all contents are included.
Hardware Bag
For Mounting Bracket:
Flat Washer x2
Star Washer x2
Spring Washer x2
Machine Screw x2
Wood Screw x2
For Wire Connection
Wire Nut x8
Mounting
Bracket
Downrod
Assembly
Canopy
Yoke
Cover
Motor
Assembly
Light Pan
LED Array
Remote
Receiver Remote Transmitter
Fan Wires
Turn off power at breaker
box to avoid possible
electrical shock.
Use metal outlet box suitable
for fan support.
Outlet box must support 35 lbs min.
Note 1: Note 2:
WARNING: blades should be at least 7 feet from floor
Light Cover
For Blade Arm Installation
Blade Screw x8 +1
Flat Washer x8 +1
Blades x4
P2
Remote
Wall Bracket
Wall Bracket
Screws x2
Wire Nuts x 5
Screw
Cover

1. HANGING SYSTEM INSTALLATION
Install mounting bracket to outlet box in ceiling
by using screws included with the outlet box
and washers from the hardware bag.
1A. Installing mounting bracket to ceiling outlet box
Downrod Jam
Screw (2)
(Tighten)
Cotter Pin
Cross Pin
Yoke
Yoke
Cover
1B. Installing Downrod and Yoke
Wires
Downrod
Assembly
Downrod Jam
Screw (2)
(Loosen)
Yoke
Remove cross pin, washer and cotter pin from downrod.
1C. Hanging the fan
Lift fan assembly onto the mounting bracket.
Rotate the fan so that the groove on the ball engages the ridge on the mounting bracket.
Fan
Assembly
Mounting
Bracket
Outlet Box
Mounting
Bracket
Mounting
Bracket
Ridge
Ball Groove
Note: Do not squeeze all the wires while
inserting the receiver into the mounting bracket.
2. Insert receiver into mounting bracket
2. RECEIVER INSTALLATION
Insert downrod thru canopy, screw cover and yoke cover, & feed motor wires thru downrod.
Loosen 2 downrod jam screws at yoke. Insert downrod assembly into yoke.
Insert the cross pin through yoke & downrod and secure with washer and cotter pin.
Tighten both downrod jam screws to further secure downrod.
Pull down the yoke cover to cover yoke.
P3
Receiver
Mounting
Bracket
Downrod
Cotter Pin
Cross Pin
Canopy
Yoke Cover
Washer
Screw Cover

5. BLADE INSTALLATION
P4
FAN MOTOR
AND LIGHT
Detailed instructions are
enclosed with the remote.
3. Making electrical wire connections
3. WIRING CONNECTION
For convenience basic
wiring connections are
shown here
Push up canopy until the screw still in the mounting bracket
is engaged with the large end of the keyhole on canopy.
Rotate canopy slightly until the screw head is engaged
in the narrow end of the key hole.
Insert the remaining canopy screw into the other
hole, and tighten both canopy screws.
4. Installing the canopy
Note: Two screws are pre-installed on mounting bracket for
canopy installation. You will need to remove one and loosen
the other slightly.
4. CANOPY INSTALLATION
Canopy
Screw
Key
Hole
Push up Screw Cover, so that the screws heads
are engaged with the large ends of the key holes
in the Screw Cover.
Rotate Screw Cover slightly until secure.
Screw
Cover
Key
Hole
5. Installing the blades
Raise blade to motor face,
aligning the holes to the motor.
Secure blade to motor face with
blade arm screws and flat washers.
Repeat for remaining blades.

Insert
Screw
Align key holes to screws
Light
Pan
Rotate
Insert
Screws
Align outermost holes
Groove
Nib
Align grooves with nibs
Rotate
Remove
one screw
Loosen
two screws
7. LIGHT/COVER INSTALLATION
Remove
three
screws
Plug In
Connectors
LED
Array
INSTALLATION IS COMPLETE
Remove three screws from the light pan.
Lift cover to motor aligning the opening of
the grooves to the nibs inside the lower plate.
Rotate cover clockwise to secure it to
motor assembly.
Remove one screw and loosen two screws
from the central hub.
Lift light pan to motor to engage the
large end of the key holes with the screws.
Rotate the plate slightly to engage two
screws in small ends of key holes.
Insert screw removed in step 1 and tighten
all three screws.
7a. Installing the Light Pan
7b. Installing the LED Array
7c. Installing the Light Cover
8. REMOTE SETTING
Plug in wire connectors, matching wire colors.
Lift LED array to light pan, aligning the
outermost holes in LED plate to the
outermost threaded holes in Light Pan.
Insert screws removed in step 1 and tighten
all three screws.
P5
Follow the separate instructions enclosed with the remote control.
This fan model has an optional integrated dimmable LED array;
Use the "D" dimming setting for the Light Function Select Switch.
6. Setting the Remote Control