TroposAir 5SR56+LK User manual

Sunrise
Owner’s Manual
5SR56+LK
WARNING : Read and follow these instructions carefully and be mindful of all warnings shown throughout.
UL
R
12 KGS.
26.44 LBS.
Net weight
This instruction contains 6 pages:
Page 1: Foreword
Page 2: Unpack and inspect parts contained
Page 3: Notes before installation and
Page 4:
Page 5: Canopy installation
Page 6: Blade / Light kit installation and Remote
Hanging system installation
Wire connection
& Setting
Toll Free: 1-855-676-7247

P1
WARNING : TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY
TO PERSONS, PLEASE OBSERVE THE FOLLOWING :
READ AND SAVE THESE INSTRUCTIONS
1]. To ensure the success of the installation, be sure to read the instructions and review the diagrams
thoroughly before beginning.
2].
All electrical connections must be made in accordance with local codes, ordinances and/or the
National Electric Code. If you are unfamiliar with the methods of installing electrical wiring and
products, secure the services of a qualified and licensed electrician as well as someone who can
check the strength of the supportive ceiling members and make the proper installations and
connections.
3]. Make sure that your installation site will not allow rotating fan blades to come in contact with any
object. Blades should be at least 7 feet from floor when fan is in operation.
4]. If possible, mount ceiling fan on a ceiling joist - the joist must be able to support the motion and weight
of the moving fan. If the fan will be mounted on a ceiling outlet box, a 4" x 2-1/8" deep METAL octagon
box is required ; one UL listed as " suitable for fan support ". The box and its supporting members must
not be able to twist or work loose. DO NOT USE PLASTIC BOXES. Installation on a concrete ceiling should
be performed by qualified personnel.
5]. Blades should be attached after motor housing is hung and in place. Fan motor housing should be
kept in carton until ready to be installed to protect its finish. If you are installing more than one ceiling
fan, make sure that you do not mix fan blade sets.
6]. After making electrical connections, spliced conductors should be turned upward and pushed
carefully up into outlet box. The wires should be spread apart with the grounded conductor and the
equipment - grounding conductor on one side of the outlet box and the " HOT " wires on the other side.
7]. Electrical diagrams are for reference only. Light kits that are not packed with the fan must be UL/ETL listed
and should be installed per the light kit's installation instructions.
8]. After fan is completely installed, check to make sure that all connections are secure to prevent fan
from falling and/or causing damage or injury.
9]. The fan can be made to work immediately after installation. The bearings are adequately charged with grease,
so that under normal conditions, further lubrication should not be necessary.
10]. The fan must be turned off and stopped before reversing fan direction.
11].
12].
13].
14].
To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring.
This fan is suitable for slope ceiling.
This fan is reversible.
This fan is controlled by remote.
This fan is suitable for indoor use.

P2
Unpack and inspect fan carefully to be certain
all contents are included.
Flat Washer x2
Spring Washer x2
Machine Screw x2 Wood Screw x2
For Mounting Bracket:
Hardware Bag
For Wire Connection:
Wire Nut x 5
For :Up Glass Assembly
Paper Washer x3
Glass Screw x3
(one spare washer included)
(one spare screw included)
For Blade Installation:
Blade Screw x 16 (one spare screw included)
Paper Washer x 16 (one spare washer included)
Motor Screw x 11 (one spare screw included)
For :Blade Balance
Balancing slide x 1
Weight block (3G x 3)
3GM 3GM 3GM
Remote
Hardware Bag
Wood Screw x2
Wire Nut x6
*Battery Included
Wires
Yoke cover
Canopy
Mounting
Bracket
Downrod
Assembly
Glass
Fan assembly
Up Glass
Assembly
Incandescent
bulb (40W) x3
Blade Holder x 5
Blade x 5
CFL Bulb
(13W) x 2
Reverse Switch
(on top of motor)

P3
WARNING: blades should be at least 7 feet from floor
1B. Downrod and YokeInstalling
OFF OFF OFF
Turn off power at breaker
box to avoid possible
electrical shock.
Use metal outlet box suitable
for fan support.
Outlet box must support 35 lbs min.
Note 1: Note 2:
1A. Installing mounting bracket to ceiling outlet box
1. HANGING SYSTEM INSTALLATION
Remove cross pin and cotter pin from downrod.
Insert downrod through canopy and yoke cover, and feed motor lead wires through downrod.
Loosen 2 downrod jam screws at yoke. Insert downrod assembly into yoke.
Insert the cross pin through yoke & downrod and secure with cotter pin.
Tighten both downrod jam screws to further secure downrod.
Pull down the yoke cover to cover yoke.
1
2
3
4
5
6
Outlet Box
Mounting
Bracket
Cross Pin
Cotter Pin
1
Canopy
Yoke cover
Downrod
Wires
Yoke
Yoke cover
Cross Pin
Yoke
Cotter Pin
Downrod
Screw(2)
(Tightening)
Jam
2
354
Downrod
Assembly
Downrod
Screw(2)
( ing)
Jam
Loosen
6
1
4
Install mounting bracket to outlet box in ceiling by using screws included with the outlet box and
washers from the hardware bag.

P4
Mounting
Bracket
2. WIRE CONNECTION
2A. Insert receiver into mounting bracket
Receiver
Mounting
Bracket
Do not sq eeze all the wires while inserting the receiver into the mounting bracket.NOTE: u
1D. Hanging the fan
Rotate fan so that the groove on the ball engages
the ridge in the mounting bracket.
Lift fan assembly onto mounting bracket.
Place the up glass assembly onto fan assembly.
Secure the up glass assembly onto fan assembly with 3 paper washers and 3 glass screws
(provided from hardware bag).
Gently install 3 incandescent bulbs (40W) to lamp holders.
provided from box
Up Glass
Assembly
1C. Attaching the Up Glass Assembly onto Fan Assembly
1
2
3
Paper Washer (3)
Glass Screw (3)
1
2
3
Incandescent
bulb 40W (3)
Fan Assembly
Mounting
Bracket
Ridge
Ball Groove

P5
!Warning! CFL bulbs are not applicable to the remote with dimming function.
2C. Setting code switches for transmitter
3. CANOPY INSTALLATION
Key Hole (2)
Canopy
Screw (2)
1
2
3
1
2
3
Push up canopy until two screws pre-screwed on mounting bracket are engaged with two key holes on canopy.
Rotate canopy slightly until two pre-installed screw heads are engaged in the narrow end of key holes.
Tighten both screws.
Note: Two screws are pre-installed on mounting bracket for canopy installation.
From House From Fan
( from downrod )
( from mounting bracket )
From Remote
( for ground wire )
( for light kit )
(AC-N)
(AC-L)
Black
White
Blue
Black
White
(Motor-N)
(Motor-L)
Secure with twist - lock wire nuts (Included).
White White
Black Black
Blue
Green
Green
Green
Orange
( for up light kit )
Orange
2B. Making electrical wire connection
Follow diagram below and make sure that all exposed wires are secured inside wire nuts.
Note: Wires from house may vary in color and may not include ground wire (green).
After wiring is completed, collect wires neatly inside hanging base.
Remove battery cover.
Slide code switch randomly using a small screwdriver or ball point pen to slide each switch firmly up or down.
Slide code switch for light ON/OFF (marked as X), or DIMMING (marked as D) function.
Install 9V DC battery.(Included)
Install battery cover on transmitter.
1.Setting the code on the TRANSMITTER
1
2
3
4
5
Remote controls are tuned to operate together using 4 switches for 16 possible code combinations.
1
45
D: for light dimming
(for incandescent bulbs )
X: for light ON/OFF
(for CFL bulbs)
Transmitter
Code Switches
12
3
4
2
X
D
ON
3
12
3
4X
D
ON
Important! This fan includes 2 CFL bulbs, so the code switch should be at X position (ON/OFF).
You may switch code at D position (DIMMING) once incandescent bulbs are installed.

5. LIGHT KIT INSTALLATION
5B.
Attach the glass shade by screwing
it onto the light kit pan clockwise.
Install the bulbs (included) to the
medium sockets properly.
5A.
P6
Groove
Glass
Shade
Medium Sockets
MED:Fan middle speed
HI:Fan high speed
LOW:Fan low speed
6. REMOTE & SETTING
D/L: ON/OFF button
for Down light
U/L: ON/OFF button
for Up light
4A. Blade Installation
Blade
Attach blade to blade holder with 3 blade screws
and 3 paper washers provided from hardware bag.
Make sure all screws are firmly tightened.
4B. Blade Assembly To Motor
Blade Screw (3)
Paper Washer (3)
Blade holder
Secure Blade Assembly to the fan assembly with
2 motor screws provided from hardware bag.
4. BLADE INSTALLATION
Blade Assembly
Motor Screw (2)
Fan Assembly
Bulb
(13W CFL bulb)
Bulb
(13W CFL bulb)
Note: You may switch Light switch code at D position
(DIMMING) when you change to incandescent bulbs
for Down light. To use dimming, press and hold light
button(s).
Pressing the button for 3~5 seconds until the , which means this remote control
has done the setting. Now the remote is ready for operation.
“OFF” LIGHT BLINKS
Turn on power at breaker box for remote setting.
2
X: for light ON/OFF
(for CFL bulbs)
D: for light dimming
(for incandescent bulbs)
12
3
4X
D
ON
12
3
4X
D
ON
OFF: For SETTING / Fan speed
SETTING of remote before starting fan