TroposAir 5HA52 User manual

ProSeries Deluxe Builder outdoor
7.0 KGS.
15.4 LBS.
Net weight
Owner’s Manual
WARNING : Read and follow these instructions carefully and be mindful of all warnings shown throughout.
UL
R
5HA52
This instruction contains 6 pages:
Page 1: Foreword
Page 2: Unpack and inspect parts contained
Page 3: Notes before installation
Page 3~5:
Page 5: C
Hanging system installation
Wire and anopy installation
Page 6: Blade / Switch Housing / Pull hain Knob installatio
Cn
Toll Free: 1-855-676-7247

WARNING : TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY
TO PERSONS, PLEASE OBSERVE THE FOLLOWING :
READ AND SAVE THESE INSTRUCTIONS
P1
1]. To ensure the success of the installation, be sure to read the instructions and review the diagrams
thoroughly before beginning.
2].
All electrical connections must be made in accordance with local codes, ordinances and/or the
National Electric Code. If you are unfamiliar with the methods of installing electrical wiring and
products, secure the services of a qualified and licensed electrician as well as someone who can
check the strength of the supportive ceiling members and make the proper installations and
connections.
3]. Make sure that your installation site will not allow rotating fan blades to come in contact with any
object. Blades should be at least 7 feet from floor when fan is in operation.
4]. If possible, mount ceiling fan on a ceiling joist - the joist must be able to support the motion and weight
of the moving fan. If the fan will be mounted on a ceiling outlet box, a 4" x 2-1/8" deep METAL octagon
box is required ; one UL listed as " suitable for fan support ". The box and its supporting members must
not be able to twist or work loose. DO NOT USE PLASTIC BOXES. Installation on a concrete ceiling should
be performed by qualified personnel.
5]. Blades should be attached after motor housing is hung and in place. Fan motor housing should be
kept in carton until ready to be installed to protect its finish. If you are installing more than one ceiling
fan, make sure that you do not mix fan blade sets.
6]. After making electrical connections, spliced conductors should be turned upward and pushed
carefully up into outlet box. The wires should be spread apart with the grounded conductor and the
equipment - grounding conductor on one side of the outlet box and the " HOT " wires on the other side.
7]. Electrical diagrams are for reference only. Light kits that are not packed with the fan must be UL/ETL listed
and should be installed per the light kit's installation instructions.
8]. After fan is completely installed, check to make sure that all connections are secure to prevent fan
from falling and/or causing damage or injury.
9]. The fan can be made to work immediately after installation. The bearings are adequately charged with grease,
so that under normal conditions, further lubrication should not be necessary.
10]. The fan must be turned off and stopped before reversing fan direction.
11].
12].
13].
14].
15]
To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring.
This fan is suitable for three mounting ways: Downrod (standard)/ Flush (Hugger) / Slope ceiling.
This fan is reversible.
This fan is light kit adaptable.
This fan is remote adaptable.
. This fan is suitable for damp location use.

Unpack and inspect fan carefully to be certain
all contents are included.
P2
Hardware Bag
For Wire Connection:
Wire Nut x 3
For Blade Installation:
Blade Screw x 16 (one spare screw included)
Rubber Washer x 16 (one spare washer included)
Motor Screw x 11 (one spare screw included)
For Fan :
Pull Chain Knob x1
For :Blade Balance
Balancing slide x 1
Weight block (3G x 3)
3GM 3GM 3GM
Downrod
Assembly
Mounting
Bracket
Canopy
Wires
Blade Holder x5
Blade x5
Yoke Cover
Canopy
Decorating Cap
For Mounting Bracket:
Switch Housing
Fan Assembly
Flat Washer x2
Spring Washer x2
Machine Screw x2 Wood Screw x2

1. HANGING SYSTEM INSTALLATION
Outlet Box
Mounting
Bracket
1A.Installing mounting bracket to ceiling outlet box
WARNING: blades should be at least 7 feet from floor
OFF OFF OFF
Turn off power at breaker
box to avoid possible
electrical shock.
Use metal outlet box suitable
for fan support.
Outlet box must support 35 lbs min.
Note 1: Note 2:
P3
Cross Pin
Cotter Pin
Canopy
Downrod
4
Downrod Jam
Screw(2)
( ing)
Loosen Yoke
Downrod
Assembly
Wires
3
Yoke cover
1B. This fan has two installation methods available:
Downrod mount (Standard) : Please follow up Step 1C and 1D.
Flush mount (Hugger) : Please directly go to Step 1E and 1F.
1
2
1C. Downrod and YokeInstalling
Remove cross pin and cotter pin from downrod.
Remove the pre-attached Gasket from the downrod assembly and keep for Step .
Insert downrod through canopy and yoke cover, and feed motor lead wires through downrod.
Loosen 2 downrod jam screws at yoke. Insert downrod assembly into yoke.
8
1
2
3
4
(See Step 1C and 1D) (SeeStep1Eand1F)
12
Downrod mount Flush mount
2
1
Gasket
(Removing)
1
Install mounting bracket to outlet box in ceiling by using screws
included with the outlet box and washers from the hardware bag.

P4
1E. Canopy Assembly (For Flush mount)
Canopy
decorating cap
Canopy
Big Screw & Washer (3)
1D. Hanging the fan (For Downrod mount)
Rotate fan so that the groove on the ball engages
the ridge in the mounting bracket.
Lift fan assembly onto mounting bracket.
Mounting
Bracket
Ridge
Ball Groove
Mounting
Bracket
2
13
Insert the cross pin through yoke & downrod and secure with cotter pin.
Tighten both downrod jam screws to further secure downrod.
Pull down the yoke cover to cover yoke.
Insert 4 wires through holes of Gasket (Removed from Step ), and put the Gasket back into downrod
assembly.
2
5
6
7
8
Gasket
8
Wires
Cross Pin
Yoke
Cotter Pin
Downrod Jam
Screw(2)
(Tightening)
65
7
Yoke cover
Fan assembly
Remove three big screws with washers and keep them for Step .
Remove canopy decorating cap from bottom of canopy.
Put the canopy onto yoke, and fasten with three big screws with washers removed from Step .
1
2
3
Note : There are three big screws and three small screws pre-attached on top of fan assembly.
1
3
Big Screw & Washer (3)
Small Screw & Washer (3)
Top of Fan Housing
Downrod
Assembly
5
3
1C (Continued)

Follow diagram below and make sure that all exposed wires are secured inside wire nuts or terminal block.
Note : Wires from house may vary in color and may not include ground wire ( green ).
From House
White
Black
From Fan
White
Black
(AC-N)
(AC-L)
(MOTOR-N)
(MOTOR-L)
Green
Green
Green
( from downrod )
( from mounting bracket )
( for ground wire )
*White wire from house to white wire from fan
*Black wire from house to black wire and blue wire from fan
*Ground wire from house to green wire from downrod and from mounting bracket
*Secure with twist - lock wire nuts. (Included)
*
After wiring is completed, gently push wires into junction box with wire nuts pointing upward.
Making electrical wire connection
Wire Form House
Blue
(For Light Kit)
Secure with twist - lock wire nuts.
3. CANOPY INSTALLATION
Outlet Box
Note: Four screws are pre-screwed on mounting bracket for canopy installation.
Left-hand
side screw
(Removing)
Remove left-hand side screw on mounting bracket first and loosen the other one.
( Please do the same for the other two screws on the across side of mounting bracket.)
Rotate the canopy slightly until both two loosening screws are in the holes of L type slots.
Tighten 4 screws firmly.
Note:
1
2
3
Screw
(Loosening)
1
3Screw (4)
()Tightening
2. WIRE CONNECTION
P5
L Type Slots
2
1F. Hanging the fan (For Flush mount)
Mounting
Bracket
Tab
Fan assembly
Lift the fan assembly and hang onto the tab on mounting bracket.
This will permit you to make the wire connections without having to hold the fan up as well.Note:

7.Turn on the power at breaker box - your fan is ready for operation.
Pull Chain Knob
Connect Pull Chain Knob provided from hardware bag to the pull chain from switch housing.
6. PULL CHAIN KNOB INSTALLATION
P6P6
Fan Assembly
2
Fan Assembly
Switch Housing
Switch Housing
Cover
1
Screw & Rubber Washer (3)
Remove 3 set screws & from switch housing cover and keep them for Step .
Fasten switch housing and the cover together with 3 set screws & removed from Step
rubber washers
rubber washers .
1
21
2
Switch Housing
Screw &
Rubber Washer (3)
5. INSTALLATIONSWITCH HOUSING
4. BLADE INSTALLATION
Attach blade to blade holder with 3 blade screws and 3 rubber washers provided from hardware bag.
Make sure all screws are firmly tightened.
Remove 3 motor stoppers by removing screws.
Secure Blade Assembly to the motor with 2 motor screws provided from hardware bag.
To prevent wobble, do not bend blade or blade holder.NOTE:
1
2
3
Blade Screw (3)
Blade Holder
Rubber Washer (3)
1
Motor
Stopper (3)
2
Motorscrew(2)
3Blade Assembly
Fan Assembly
Blade