TroposAir 59DFG-L User manual

Owner’s ManualOwner’s Manual
St. Augustine
Toll Free 1-855-676-7247
WARNING: Read and follow these instructions carefully and be mindful of all warnings shown throughout.
Net Weight
8.46 KGS
18.6 LBS
These instructions contain 4 pages:
Page 1: Foreword
Page 2: Unpack and inspect parts contained, and pre-installation notes
Page 3: Light /Cover Installation
Page 4: Hanging system installation
Page 5: Wiring connections, Canopy and Blade installation and Remote Setting
Model No:
59DFG-L
HS-1233-F

To ensure success of installation, be sure read these instructions and review the
diagrams thoroughly before beginning.
To avoid possible electric shock, be sure electricity is turned off at the main
power box before wiring.
All electrical connections must be made in accordance with local codes, ordinances
and/or the National Electrical Code. If you are unfamiliar with the methods of installing
electrical wiring and products, secure the services of a qualified and licensed
electrician as well as someone who can check the strength of the supportive ceiling
members and make the proper installations and connections.
Make sure that your installation site will not allow rotating fan blades to come into
contact with any object. Blades should be at least 7 feet from the floor when fan is in
operation.
If possible, mount ceiling fan on a ceiling joist - the joist must be able to support the
motion and weight of the moving fan. If the fan will be mounted on a ceiling outlet box,
a 4” x 2 1/8” deep METAL octagon box is required; one UL listed as “suitable for fan
support”. The box and its supporting members must not be able to twist or work loose.
DO NOT USE PLASTIC BOXES. Installation on a concrete ceiling should be
performed by qualified personnel.
Blades should be attached after motor housing is hung and in place. Fan motor
housing should be kept in carton until ready to be installed to protect its finish. If you
are installing more than one ceiling fan, make sure that you do not mix fan blade sets.
After making electrical connections, spliced conductors should be turned upward and
pushed carefully up into the outlet box. The wires should be spread apart with the
grounded conductor and the equipment-grounding conductor on one side of the outlet
box and the “HOT” wires on the other side.
Electrical diagrams are for reference only. Light kits that are not packed with the fan
must be UL/ETL listed and should be installed per the light kit’s installation instructions.
After fan is completely installed, check to make sure that all connections are secure to
prevent fan from falling and/or causing damage or injury.
The fan can be made to work immediately after installation. The bearings are
adequately charged with grease, so that, under normal conditions, further lubrication
should not be necessary.
The fan must be turned off and stopped before reversing fan direction.
This fan is suitable for sloped ceiling.
This fan is electrically reversible.
This fan includes an integrated light kit.
This fan is controlled by remote control.
This fan is suitable for indoor use, and damp location use in the US.
READ AND SAVE THESE INSTRUCTIONS
WARNING : TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY
TO PERSONS, PLEASE OBSERVE THE FOLLOWING:
1.]
2.]
3.]
4.]
5.]
6.]
7.]
8.]
9.]
10.]
11.]
12.]
13.]
14.]
15.]

1
2
3
4
5
6
2H
4H
8H
Unpack and inspect fan carefully to be certain
all contents are included.
Hardware Bag
For Mounting Bracket:
Flat Washer x2
Star Washer x2
Spring Washer x2
Machine Screw x2
Wood Screw x2
For Wire Connection
Wire Nut x3
For Blade Installation
Blade Screw x15 +1
Blade Washer x15 +1
Mounting
Bracket
Downrod
Assembly
Canopy
Yoke
Cover
Motor
Assembly
Bulb
60W Max
Blade x5
Remote
Receiver Remote Transmitter
Remote
Wall Bracket
Wall Bracket
Screws x2
Wire Nuts x 5
Turn off power at breaker
box to avoid possible
electrical shock.
Use metal outlet box suitable
for fan support.
Outlet box must support 35 lbs min.
Note 1: Note 2:
WARNING: blades should be at least 7 feet from floor
Glass Shade
with Grill
For Light Grill Cover
Light Grill Screw x3
Light Socket Fixture
Screws for Light
Socket Fixture (4)
Light Pan

Plug In
Connectors
Light
Socket
Fixture
Screws for
Light Socket
(4)
1. LIGHT/COVER INSTALLATION
Align three holes in light grill with
three holes in motor assembly.
Lower light grill into position.
Secure light grill to motor assembly
using three (3) screws for light cover.
1C. Installing the Light Grill
Align
Key Holes
Rotate
Light
Pan
Install Screw
and tighten
1B. Installing the Light Fixture
Install the bulb
into the socket.
Plug in wire connectors, matching wire colors.
Secure light socket fixture to motor assembly
using four (4) screws for light socket fixture.
Install Bulb
Note: Four screws are pre-installed on Light Pan for light
socket fixture installation. You will need to remove these screws.
Screws for
Light Grill (3)
Lower
Light Grill
Align Holes
After feeding the light wires through the center hole, lower
the Light Pan onto motor assembly aligning the two loosened
screws with the large end of the key holes.
Rotate Light Pan slightly so that screws are engaged in narrow
end of key holes.
Install the screw remove earlier and tighten all three screws.
Note: Three screws are pre-installed on motor assembly for light
pan installation. You will need to remove one and loosen two of
these screws.
1A. Installing the Light Pan
Hint: Lay the motor assembly on the styrofoam packing with the light wires up,

Downrod Jam
Screw (2)
(Tighten)
Cotter Pin
Yoke
Cover Cross Pin
Yoke
2. HANGING SYSTEM INSTALLATION
Install mounting bracket to outlet box in ceiling
by using screws included with the outlet box
and washers from the hardware bag.
2A. Installing mounting bracket to ceiling outlet box
2B. Installing Downrod and Yoke
Wires
Downrod
Assembly
Downrod
Jam Screw (2)
(Loosen)
Yoke
Remove cross pin, washer and cotter pin from downrod.
Insert downrod through canopy and yoke cover, and feed motor wires through downrod.
Loosen 2 downrod jam screws at yoke. Insert downrod assembly into yoke.
Insert the cross pin through yoke & downrod and secure with washer and cotter pin.
Tighten both downrod jam screws to further secure downrod.
Pull down the yoke cover to cover yoke.
Mounting
Bracket
Ridge
Ball Groove
2C. Hanging the fan
Lift fan assembly onto the mounting bracket. Rotate the fan so that the groove on the ball
engages the ridge on the mounting bracket.
Fan
Assembly
Mounting
Bracket
Outlet Box
Mounting
Bracket
Align key holes to screws
Downrod
Cotter Pin
Cross Pin
Canopy
Yoke Cover
Washer

Receiver
Mounting
Bracket
4. CANOPY INSTALLATION
5. BLADE INSTALLATION
Blade
Screws &
Washers
(3)
Blade
Arm
Slot
Blade
5. Installing the blades
Slide blade into a slot in motor above a blade arm.
Secure blade to blade arm using three
blade screws and washers.
Repeat for remaining blades
and retighten all screws.
Canopy
Screw
Key
Hole
Push up canopy until the screw still in the mounting bracket
is engaged with the large end of the keyhole on canopy.
Rotate canopy slightly until the screw head is engaged
in the narrow end of the key hole.
Insert the remaining canopy screw into the other hole,
and tighten both canopy screws.
4. Installing the canopy
Note: Two screws are pre-installed on mounting bracket for
canopy installation. You will need to remove one and loosen
the other slightly.
Note: Do not squeeze all the wires while
inserting the receiver into the mounting bracket.
3A. Insert receiver into mounting bracket
Follow separate instructions enclosed with the remote control.
3B. Making electrical wire connections
3. WIRING CONNECTION
6. REMOTE SETTING
INSTALLATION IS COMPLETE
Follow the separate instructions enclosed with the remote control.
This fan model has an optional integrated dimmable LED array;
Use the "D" dimming setting for the Light Function Select Switch.
6. Setting the Remote Control