TroposAir Enterprise III User manual

Owner’s ManualOwner’s Manual
Enterprise III
Toll Free 1-855-676-7247
WARNING: Read and follow these instructions carefully and be mindful of all warnings shown throughout.
Net Weight
7.72 KGS
17.0 LBS
These instructions contain 5 pages:
Page 1: Foreword
Page 2: Unpack and inspect parts contained, and pre-installation notes
Page 3: Hanging system installation and Remote setting
Page 4: Wire connection and Canopy installation
Page 5: Blade and Light/Cover installation
Model No: 50NDE-L

To ensure success of installation, be sure read these instructions and review the
diagrams thoroughly before beginning.
To avoid possible electric shock, be sure electricity is turned off at the main
power box before wiring.
All electrical connections must be made in accordance with local codes, ordinances
and/or the National Electrical Code. If you are unfamiliar with the methods of installing
electrical wiring and products, secure the services of a qualified and licensed
electrician as well as someone who can check the strength of the supportive ceiling
members and make the proper installations and connections.
Make sure that your installation site will not allow rotating fan blades to come into
contact with any object. Blades should be at least 7 feet from the floor when fan is in
operation.
If possible, mount ceiling fan on a ceiling joist - the joist must be able to support the
motion and weight of the moving fan. If the fan will be mounted on a ceiling outlet box,
a 4” x 2 1/8” deep METAL octagon box is required; one UL listed as “suitable for fan
support”. The box and its supporting members must not be able to twist or work loose.
DO NOT USE PLASTIC BOXES. Installation on a concrete ceiling should be
performed by qualified personnel.
Blades should be attached after motor housing is hung and in place. Fan motor
housing should be kept in carton until ready to be installed to protect its finish. If you
are installing more than one ceiling fan, make sure that you do not mix fan blade sets.
After making electrical connections, spliced conductors should be turned upward and
pushed carefully up into the outlet box. The wires should be spread apart with the
grounded conductor and the equipment-grounding conductor on one side of the outlet
box and the “HOT” wires on the other side.
Electrical diagrams are for reference only. Light kits that are not packed with the fan
must be UL/ETL listed and should be installed per the light kit’s installation instructions.
After fan is completely installed, check to make sure that all connections are secure to
prevent fan from falling and/or causing damage or injury.
The fan can be made to work immediately after installation. The bearings are
adequately charged with grease, so that, under normal conditions, further lubrication
should not be necessary.
The fan must be turned off and stopped before reversing fan direction.
This fan is suitable for sloped ceiling.
This fan is reversible by switch on top of motor.
This fan includes an integrated light kit.
This fan is controlled by remote control.
This fan is suitable for indoor use.
READ AND SAVE THESE INSTRUCTIONS
WARNING : TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY
TO PERSONS, PLEASE OBSERVE THE FOLLOWING:
1.]
2.]
3.]
4.]
5.]
6.]
7.]
8.]
9.]
10.]
11.]
12.]
13.]
14.]
15.]

Unpack and inspect fan carefully to be certain
all contents are included.
Hardware Bag
For Mounting Bracket:
Flat Washer x2
Star Washer x2
Spring Washer x2
Machine Screw x2
Wood Screw x2
For Wire Connection
Wire Nut x3
For Blade Installation
Blade Screw x9 +1
Blade Washer x9 +1
Countersink Screws x6 +1
Mounting
Bracket
Downrod
Assembly
Canopy
Yoke
Cover
Reverse
Switch
(on top
of motor)
Motor
Assembly
Glass
Shade
G9 50W Bulb
Blade x3
Remote
Receiver Remote Transmitter
Remote
Wall Bracket
Wall Bracket
Screws x2
Wire Nuts x 5
Fan Wires
Turn off power at breaker
box to avoid possible
electrical shock.
Use metal outlet box suitable
for fan support.
Outlet box must support 35 lbs min.
Note 1: Note 2:
WARNING: blades should be at least 7 feet from floor
Trim
Arch x3
LIGHT ON/OFF
MED HILO
FAN OFF
Light
Pan

1. HANGING SYSTEM INSTALLATION
Install mounting bracket to outlet box in ceiling
by using screws included with the outlet box
and washers from the hardware bag.
1A. Installing mounting bracket to ceiling outlet box
1B. Installing Downrod and Yoke
Wires
Downrod
Assembly
Downrod Jam
Screw (2)
(Loosen)
Yoke Downrod Jam
Screw (2)
(Tighten)
Cotter Pin Yoke
Cover Cross Pin
Yoke
Remove cross pin washer and cotter pin from downrod.
Insert downrod through canopy and yoke cover, and feed motor wires through downrod.
Loosen 2 downrod jam screws at yoke. Insert downrod assembly into yoke.
Insert the cross pin through yoke & downrod and secure with washer and cotter pin.
Tighten both downrod jam screws to further secure downrod.
Pull down the yoke cover to cover yoke.
Fan
Assembly
Mounting
Bracket
Mounting
Bracket
Ridge
Ball Groove
1C. Hanging the fan
Lift fan assembly onto the mounting bracket. Rotate the fan so that the groove on the ball
engages the ridge on the mounting bracket.
Outlet Box
Mounting
Bracket
2. REMOTE CONTROL
Downrod
Cotter
Pin
Cross Pin
Canopy
Yoke Cover
Washer
Follow separate instructions enclosed with the remote control.
Canopy
Screw
Key Hole
Push up canopy until the screw still in the mounting bracket
is engaged with the large end of the keyhole on canopy.
Rotate canopy slightly until the screw head is engaged
in the narrow end of the key hole.
Insert the remaining canopy screw into the other hole,
and tighten both canopy screws.
3. Installing the canopy
Note: Two screws are pre-installed on mounting bracket for canopy
installation. You will need to remove one and loosen the other slightly.
3. CANOPY INSTALLATION

Remove
one screw
Loosen
two screws
Insert
Screw
Rotate
Align key holes to screws
Plug in
Connectors Light
Pan
4. BLADE INSTALLATION
4. Installing the blades Countersink
Screws (2)
Blade
Screws &
Washers
(3)
Blade
Blade Arm
Align three smaller holes in blade with the three posts
on blade arm and secure with blade screws and washers.
Repeat for remaining blades.
Position trim arch as shown and secure to motor and
to blade arm using the countersink screws.
Repeat for remaining trim arches.
5. LIGHT/COVER INSTALLATION
Insert
G9 Bulbs (2)
Nib
Groove
Glass
Shade
5A. Installing the Light Pan
5B. Installing the Glass Shade
Insert both G9 Bulbs (50W) into sockets.
Lift glass to motor aligning the groves in the neck of the
glass to the nibs inside the lower plate.
Rotate glass clockwise to secure it to motor assembly.
TURN POWER ON AT THE BREAKER
Remove one screw and loosen two screws
from the central hub of the motor assembly.
Plug in Wire Connectors, matching wire colors.
Lift light pan to motor to engage the
large end of the key holes with the screws.
Rotate the light pan slightly to engage two
screws in small ends of key holes.
Insert screw removed in step 1 and tighten
all three screws.