Trotec BD 7A User manual

TRT-BA-BD7A-TC2018-61-001-EN
BD7A
EN
OPERATING MANUAL
CROSS LINE LASER

2 EN
cross line laser BD7A
Table of contents
Notes regarding the operating manual.................................2
Safety .....................................................................................2
Information about the device................................................4
Transport and storage...........................................................5
Operation ...............................................................................6
Maintenance and repair ........................................................9
Errors and faults....................................................................9
Disposal .................................................................................9
Notes regarding the operating manual
Symbols
Warning of electrical voltage
This symbol indicates dangers to the life and health of
persons due to electrical voltage.
Warning of laser radiation
This symbol indicates dangers to the health of persons
due to laser radiation.
Warning
This signal word indicates a hazard with an average
risk level which, if not avoided, can result in serious
injury or death.
Caution
This signal word indicates a hazard with a low risk
level which, if not avoided, can result in minor or
moderate injury.
Note
This signal word indicates important information (e.g.
material damage), but does not indicate hazards.
Info
Information marked with this symbol helps you to carry
out your tasks quickly and safely.
Follow the manual
Information marked with this symbol indicates that the
operating manual must be observed.
You can download the current version of the operating manual
and the EU declaration of conformity via the following link:
BD7A
https://hub.trotec.com/?id=42892
Safety
Read this manual carefully before starting or using the
device. Always store the manual in the immediate vicinity
of the device or its site of use!
Warning
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may
result in electric shock, fire and/ or serious injury.
Save all warnings and instructions for future
reference.
This appliance can be used by children aged from
8years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children
without supervision.
• Do not use the device in potentially explosive rooms.
• Do not use the device in aggressive atmosphere.
• Do not immerse the device in water. Do not allow liquids to
penetrate into the device.
• The device may only be used in dry surroundings and must
not be used in the rain or at a relative humidity exceeding
the operating conditions.
• Protect the device from permanent direct sunlight.
• Do not remove any safety signs, stickers or labels from the
device. Keep all safety signs, stickers and labels in legible
condition.
• Do not open the device with a tool.
• Avoid looking directly into the laser beam.
• Never point the laser beam at people or animals.
• Only use the device if sufficient safety precautions were
taken at the surveyed location (e.g. when performing
measurements along public roads, on building sites etc.).
Otherwise do not use the device.
• Observe the storage and operating conditions as given in
the Technical data chapter.

EN 3
cross line laser BD7A
Intended use
Only use the device BD7A for the projection on non-reflective
surfaces as an aid to determine and check horizontal, vertical
and/ or parallel lines. Observe and comply with the technical
data.
To use the device for its intended use, only use accessories and
spare parts which have been approved by Trotec.
Improper use
Do not use the device BD7A in potentially explosive
atmospheres or in liquids. Never point it at people or animals.
Trotec accepts no liability for damages resulting from improper
use. In such a case, any warranty claims will be voided.
Any unauthorised modifications, alterations or structural
changes to the device are forbidden.
Personnel qualifications
People who use this device must:
• be aware of the dangers that occur when working with
laser measuring devices.
• have read and understood the operating manual, especially
the Safety chapter.
Residual risks
Warning of electrical voltage
There is a risk of a short-circuit due to liquids
penetrating the housing!
Do not immerse the device and the accessories in
water. Make sure that no water or other liquids can
enter the housing.
Warning of electrical voltage
Work on the electrical components must only be
carried out by an authorised specialist company!
Warning of explosive substances
Do not expose the battery to temperatures above 45
°C! Do not let the battery come into contact with water
or fire! Avoid direct sunlight and moisture. There is a
risk of explosion!
Warning of laser radiation
Laser class2, Pmax.: <1mW, λ: 650nm,
EN60825-1:2014
Do not look directly into the laser beam or the opening
from which it emerges.
Never point the laser beam at people, animals or
reflective surfaces. Even brief eye contact can lead to
eye damage.
Examining the laser output aperture by use of optical
instruments (e.g. magnifying glass, magnifiers and the
like) entails the risk of eye damage.
When working with a laser of class2, observe the
national regulations on wearing eye protection.
Warning
Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
Warning
The device is not a toy and does not belong in the
hands of children.
Warning
Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way!
Observe the personnel qualifications!
Caution
Keep a sufficient distance from heat sources.
Note
To prevent damages to the device, do not expose it to
extreme temperatures, extreme humidity or moisture.
Note
Do not use abrasive cleaners or solvents to clean the
device.

4 EN
cross line laser BD7A
Information about the device
Device description
The cross line laserBD7A projects laser lines on surfaces,
e.g. to drill holes in a straight line – similar to using a spirit
level.
The device comes with the following features:
• Projects light-intense laser lines up to a distance of 10m
• Self-levelling up to an inclination of 3°
• Laser projection either as cross line, individual vertical line
or horizontal 360° line
• Self-levelling function can be deactivated
• Battery-powered
• Integrated ¼ inch tripod connection
Device depiction
1
2
3
4
5
No. Designation
1 360° laser outlet opening
2 Operating elements
3 Vertical laser outlet opening
4 1/4inch tripod connection
5 MicroUSB charging port
Operating elements
9
8
6
7
No. Operating element
6 ON/ OFF/ operating mode button
7 ON/ OFF/ lock switch
8 Levelling indicator "Level" (green LED)
9 Levelling indicator "NO Level" (red LED)
Multifunctional mount
10
11
12
13
14
15
16
No. Designation
10 Screw (for tripod connection)
11 Wing nut (for ball joints)
12 Locking screw (for retainer with jaws)
13 Lever (for suction cup)
14 Suction cup
15 Retainer with jaws
16 Ball joint

EN 5
cross line laser BD7A
Technical data
Parameter Value
Model BD7A
Device dimensions
(lengthx widthx height)
60 x 60 x 115mm
Device weight 280g
Multifunctional mount dimensions
(length x width x height)
125x 81x 220 mm
Multifunctional mount weight 189g
Interfaces Micro USB port for
charger
Range 10 m
Operating temperature -20°C to 50°C
Storage temperature -20°C to 50°C
Levelling duration <6s
Laser output <1 mW (650 nm)
Laser accuracy at 0°: ±0.8mm/m
at ≤3°: ±1mm/m
Laser class 2
Energy
Battery Li-ion
Capacity 1000 mAh
Charging time 3 to 4 hours
Nominal voltage 3.7V
Operating time approx. 5 hours of
continuous operation
Automatic switch-off When the battery is low,
the levelling indicator
"NO Level"(9) flashes
for one minute before
the device turns off
automatically
Scope of delivery
• 1x Cross line laser BD7A
• 1x Multifunctional mount
• 1 x USB cable
• 1x Manual
Transport and storage
Note
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
Transport
The supplied Li-ion batteries are subjects to the requirements of
dangerous goods legislation.
Observe the following when transporting or shipping Li-ion
batteries:
• The user may transport the batteries by road without any
additional requirements.
• If transport is carried out by third parties (e.g. air transport
or forwarding company), special requirements as to
packaging and labelling must be observed. This includes
consulting a dangerous goods specialist when preparing
the package.
– Only ship batteries if their housing is undamaged.
– Please also observe any other national regulations.
For transporting the device use a suitable bag to protect it from
external influences.
Storage
When the device is not being used, observe the following
storage conditions:
• dry and protected from frost and heat
• protected from dust and direct sunlight
• with a cover to protect it from invasive dust if necessary
• The storage temperature is the same as the range given in
the Technical data chapter.

6 EN
cross line laser BD7A
Operation
Charging the battery
The battery is partially charged upon delivery to avoid damage
to the battery caused by a deep discharge.
Info
Upon delivery, the battery is only slightly charged.
Therefore, please charge the battery for at least
5hours before using the device for the first time.
Warning of laser radiation
Laser class2, Pmax.: <1mW, λ: 650nm,
EN60825-1:2014
Do not look directly into the laser beam or the opening
from which it emerges.
Never point the laser beam at people, animals or
reflective surfaces. Even brief eye contact can lead to
eye damage.
Examining the laser output aperture by use of optical
instruments (e.g. magnifying glass, magnifiers and the
like) entails the risk of eye damage.
When working with a laser of class2, observe the
national regulations on wearing eye protection.
Warning of electrical voltage
Before each use of the charger or power cable, check
for damages. If you notice damages, stop using the
charger or power cable!
Note
The battery can be damaged in case of improper
charging.
Never charge the battery at ambient temperatures
below 10°C or above 40°C.
The battery should be charged prior to initial start-up and when
the battery is low. To do so, please proceed as follows:
1. Unscrew the device from the multifunctional mount.
2. Plug the charger into a properly fused mains socket.
3. Connect the charging cable to the device's micro USB port.
4. During charging, the levelling indicator "NO Level"(9) is
illuminated in red.
5. When the battery is fully charged, the levelling indicator
"Level"(8) lights up in green.
Switching the device on
The device has twodifferent modes of operation. On the one
hand, you can use the device with the automatic self-levelling
function, on the other, it is possible to set the laser to a fix
position.
Self-levelling function of the laser
1. Place the device on a horizontal, solid surface or secure it
to the multifunctional mount.
2. Slide the on/off switch(7) to to switch the device on.
ðBoth the vertical laser and the horizontal 360° laser
switch on.
ðThe device automatically compensates for unevenness
within the self-levelling range of ± 3°. During levelling,
the laser lines move.
ðWhen levelling is completed, the levelling indicator
"Level"(8) lights up in green.

EN 7
cross line laser BD7A
Info
When exceeding the permissible inclination range of
3°, the lasers begin to flash and the levelling indicator
"NO Level"(9) will be illuminated in red. If so, self-
levelling will not function properly. This may be due to
the fact that the surface structure is not even enough
or covered with dirt, so the device is positioned too
obliquely to be able to self-level within the possible
angle of 3°. Check the surface, and reposition the
device if required.
3. Press the operating mode button(6) to activate the vertical
laser only or the horizontal 360° laser only.
1x
2x
4. Slide the on/off switch(7) back to to switch the device
off.
Fixed position of the lasers
Info
In this operating mode the device's self-levelling
function is deactivated.
1. Check whether the lock switch(7) is set to .
2. Press the operating mode button(6) to switch both lasers
on.
3. Press the operating mode button(6) a second time to only
activate the horizontal laser.
4. Press the operating mode button(6) a third time to only
activate the vertical laser.
5. Press the operating mode button(6) a fourth time to switch
the device off.
Using the multifunctional mount
Proceed as follows to use the multifunctional mount with the
device:
1. Screw the mount into the tripod connection at the device.
By means of the suction cup you can affix the mount to smooth
surfaces such as tiles or glass.
Alternatively, the clamping jaws can be used to fasten it to a
shelf or the edge of a table.
Swivelling the device
1. Loosen the wing nut(11).
2. Swivel the device on the ball joints to move it into the
desired position.
3. Retighten the wing nut(11).

8 EN
cross line laser BD7A
Application example for the universal clamp
1. Loosen the locking screw(12) and push the clamping
jaws(15) apart until they fit onto the carrier (here: shelf).
2. Tighten the screw(12) until the jaws(15) of the universal
clamp are firmly attached to the carrier and the mount can
no longer be moved to and fro.
3. To unfasten the clamping jaws(15), loosen the screw(12)
until the retainer can be removed from the carrier without
difficulty.
Application example for the suction cup
1. Make sure that the surface is smooth and clean.
2. Disengage the lever(13) at the suction cup(14).
3. Press the suction cup(14) against the surface (here: tiles).
4. Engage the lever(13) until it locks in place.
5. Check the suction cup(14) for tight fit.
6. In order to remove the suction cup(14) again, release the
lever(13), then pull at the lug of the suction cup.

EN 9
cross line laser BD7A
Maintenance and repair
Charging the battery
The battery should be charged prior to initial start-up and when
the battery is low. To do so, please follow the instructions in the
chapter Operation.
Cleaning
Clean the device with a soft, damp and lint-free cloth. Make
sure that no moisture enters the housing. Do not use any
sprays, solvents, alcohol-based cleaning agents or abrasive
cleaners, but only clean water to moisten the cloth.
Repair
Do not modify the device or install any spare parts. For repairs
or device testing, contact the manufacturer.
Errors and faults
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.
Self-levelling is not possible:
1. Check whether the lock switch(7) is released and the laser
can move freely. If the laser is not able to move back and
forth freely within the 3° angle despite the lock switch
being released, please contact the customer service.
2. Check the surface on which the device is placed.
If necessary, remove coarse dirt.
Laser lines are not properly horizontal/vertical:
• Check the laser for freedom of movement in self-levelling
mode. If the laser is not able to move back and forth freely
within the 3° angle despite the lock switch being released,
please contact the customer service.
Horizontal laser lines are partially interrupted:
• The lateral struts of the protective cover accommodating
the laser cause interruptions in the horizontal 360° laser
line at defined points. This cannot be avoided. Should you
detect interruptions at other points, please check the glass
covers of the protective cover for scratches or dirt, which
may be the cause of the laser beam interruptions. Remove
external dirt with a damp cloth. Do not use any aggressive
cleaning agents (see chapter Cleaning)! If you detect dirt
underneath the glass covers or scratches, please contact
the customer service.
Laser is weak:
• Check the battery status and recharge the battery if
necessary.
Disposal
The icon with the crossed-out waste bin on waste
electrical or electronic equipment stipulates that this equipment
must not be disposed of with the household waste at the end of
its life. You will find collection points for free return of waste
electrical and electronic equipment in your vicinity. The
addresses can be obtained from your municipality or local
administration. For further return options provided by us please
refer to our website www.trotec24.com.
The separate collection of waste electrical and electronic
equipment aims to enable the re-use, recycling and other forms
of recovery of waste equipment as well as to prevent negative
effects for the environment and human health caused by the
disposal of hazardous substances potentially contained in the
equipment.
Li-Ion
In the European Union, batteries and accumulators must not be
treated as domestic waste, but must be disposed of
professionally in accordance with Directive 2006/66/EC of the
European Parliament and of the Council of 6September 2006
on batteries and accumulators. Please dispose of batteries and
accumulators according to the relevant legal requirements.

Trotec GmbH & Co. KG
Grebbener Str. 7
D-52525 Heinsberg
+49 2452 962-400
+49 2452 962-200
www.trotec.com
Other manuals for BD 7A
1
Table of contents
Other Trotec Laser Level manuals